TLV2404IPWR Equivalent & Substitute Parts

Part Overview

The TLV2404IPWR is a general-purpose operational amplifier manufactured by Texas Instruments, featuring four independent circuits in a 14-TSSOP surface-mount package. This device is classified as Active product status and is designed for rail-to-rail output applications across a wide supply voltage range of 2.5V to 16V. The TLV2404IPWR is suitable for low-power, general-purpose amplification circuits requiring compact packaging and minimal component count.

Substitute parts are identified when equivalent functional performance can be achieved within the constraints of the allowed electrical and mechanical parameters for this operational amplifier category. Substitution eligibility is determined by matching package type, pin count, output configuration, and operating temperature range.

Substiute Parts

TLV2404IPWR

Texas InstrumentsIn Stock: 3144TLV2404IPWR Datasheet

Current PartRFQ

MCP6H04-E/ST

Microchip TechnologyIn Stock: 2946MCP6H04-E/ST Datasheet

MFR RecommendedRFQ

MCP6H04T-E/ST

Microchip TechnologyIn Stock: 3828MCP6H04T-E/ST Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitute parts for the TLV2404IPWR are qualified based on the following criteria:

Mandatory Matching Parameters:

• Package Type: 14-TSSOP surface-mount package with 0.173" width (4.40mm)
• Number of Circuits: 4 independent operational amplifier circuits
• Output Configuration: Rail-to-rail output capability
• Operating Temperature Range: -40°C to 125°C minimum
• Amplifier Classification: General-purpose operational amplifier
• RoHS Compliance: ROHS3 Compliant status

Substitute Parts Identified:

1. MCP6H04T-E/ST (Microchip Technology) — Tape & Reel packaging
2. MCP6H04-E/ST (Microchip Technology) — Tube packaging

Both substitute parts meet all mandatory matching parameters. They are manufactured by Microchip Technology and maintain identical package geometry, circuit count, output type, and temperature operating range as the TLV2404IPWR. Both parts are Active product status and ROHS3 compliant.

Parameter Comparison

Engineering Selection Recommendations

Packaging Consideration:

The TLV2404IPWR is supplied in Tape & Reel (TR) packaging. When selecting a substitute part, packaging format must align with assembly requirements:

• MCP6H04T-E/ST is supplied in Tape & Reel (TR) packaging, matching the original part's packaging format.
• MCP6H04-E/ST is supplied in Tube packaging and represents an alternative packaging option.

Compliance and Product Status:

All three parts—TLV2404IPWR, MCP6H04T-E/ST, and MCP6H04-E/ST—maintain Active product status, ensuring long-term availability and manufacturing support. All parts are ROHS3 compliant and carry MSL Level 1 (Unlimited) moisture sensitivity classification, indicating equivalent handling and storage requirements.

Supply Voltage Compatibility:

The TLV2404IPWR operates across a minimum supply voltage of 2.5V, while both MCP6H04 variants require a minimum of 3.5V. Applications requiring operation below 3.5V supply voltage cannot use the MCP6H04 series as direct substitutes. Both substitute parts support the maximum 16V supply voltage specification.

Electrical Performance Differences:

The MCP6H04 series exhibits higher slew rate (0.8V/µs versus 0.0025V/µs) and significantly higher gain bandwidth product (1.2MHz versus 5.5kHz). The MCP6H04 series also provides lower input bias current (10pA versus 100pA) and reduced supply current consumption (135µA total versus 900nA total). These differences indicate the MCP6H04 series is optimized for higher-speed applications, while the TLV2404IPWR is optimized for ultra-low-power operation.

Frequently Asked Questions (FAQ)

Q: Can MCP6H04T-E/ST and MCP6H04-E/ST be used interchangeably with TLV2404IPWR?

A: Both MCP6H04 variants are mechanically and functionally compatible substitutes for the TLV2404IPWR in applications where the minimum supply voltage requirement of 3.5V is satisfied. The primary difference between MCP6H04T-E/ST and MCP6H04-E/ST is packaging format: Tape & Reel versus Tube. Select based on your assembly process requirements.

Q: What is the key difference between TLV2404IPWR and MCP6H04 series?

A: The TLV2404IPWR is optimized for ultra-low-power applications with minimal supply current consumption (900nA total). The MCP6H04 series is optimized for higher-speed signal processing with significantly higher slew rate and gain bandwidth product. The MCP6H04 series also requires a higher minimum supply voltage (3.5V versus 2.5V).

Q: Are there any pin-compatibility concerns when substituting these parts?

A: No. All three parts use the 14-TSSOP package with identical pin assignments for four operational amplifier circuits. Pin-to-pin compatibility is confirmed.

Q: Which substitute part should I select if I require Tape & Reel packaging?

A: Select MCP6H04T-E/ST, which is supplied in Tape & Reel (TR) packaging, matching the original TLV2404IPWR packaging format.

Q: Can I use these substitutes in applications requiring supply voltages below 3.5V?

A: No. The MCP6H04 series requires a minimum supply voltage of 3.5V. If your application requires operation at 2.5V supply voltage, the TLV2404IPWR is the only qualified option among these parts.

Q: Are all three parts RoHS compliant?

A: Yes. TLV2404IPWR, MCP6H04T-E/ST, and MCP6H04-E/ST are all ROHS3 compliant with MSL Level 1 (Unlimited) moisture sensitivity classification.