TLV2404IPW Equivalent & Substitute Parts

Part Overview

The TLV2404IPW is a general-purpose operational amplifier manufactured by Texas Instruments, featuring four independent circuits in a 14-TSSOP surface-mount package. This device is classified as Active product status and is designed for rail-to-rail output applications across a wide supply voltage range of 2.5V to 16V. The TLV2404IPW is suitable for low-power, low-speed signal conditioning and amplification applications requiring minimal input bias current and compact packaging.

Substitute parts are identified when equivalent functional performance can be achieved within the constraints of the allowed electrical and mechanical parameters for this operational amplifier category, specifically maintaining the 4-circuit configuration, 14-TSSOP package format, and rail-to-rail output capability.

Substiute Parts

TLV2404IPW

Texas InstrumentsIn Stock: 2126TLV2404IPW Datasheet

Current PartRFQ

MCP6H04-E/ST

Microchip TechnologyIn Stock: 2946MCP6H04-E/ST Datasheet

MFR RecommendedRFQ

MCP6H04T-E/ST

Microchip TechnologyIn Stock: 3828MCP6H04T-E/ST Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitute parts for the TLV2404IPW are qualified based on the following criteria:

Mandatory Matching Parameters:

• Amplifier Type: General Purpose
• Number of Circuits: 4
• Output Type: Rail-to-Rail
• Package / Case: 14-TSSOP (0.173", 4.40mm Width)
• Mounting Type: Surface Mount
• Operating Temperature Range: -40°C to 125°C
• RoHS Status: ROHS3 Compliant
• Moisture Sensitivity Level: 1 (Unlimited)

Allowed Variation Parameters:

• Voltage Supply Span: Minimum supply voltage may be higher; maximum supply voltage must equal or exceed 16V
• Slew Rate: May vary
• Gain Bandwidth Product: May vary
• Current - Input Bias: May vary
• Voltage - Input Offset: May vary
• Current - Supply: May vary
• Current - Output / Channel: May vary
• Packaging Format: Tube or Tape & Reel (TR) acceptable

The substitute parts MCP6H04-E/ST and MCP6H04T-E/ST meet all mandatory matching parameters and are therefore qualified as electrical and mechanical equivalents for the TLV2404IPW.

Parameter Comparison

Engineering Selection Recommendations

Both MCP6H04-E/ST and MCP6H04T-E/ST are qualified substitutes for the TLV2404IPW based on compliance with mandatory electrical and mechanical parameters. All three parts maintain Active product status and ROHS3 compliance.

MCP6H04-E/ST (Tube Packaging): This variant is supplied in tube packaging format, matching the original TLV2404IPW packaging method. It is suitable for applications where tube packaging is preferred for handling and storage.

MCP6H04T-E/ST (Tape & Reel Packaging): This variant is supplied in Tape & Reel format, suitable for high-volume automated assembly operations. The electrical specifications are identical to the MCP6H04-E/ST.

Supply Voltage Consideration: The minimum supply voltage for both MCP6H04 variants is 3.5V, compared to 2.5V for the TLV2404IPW. Applications requiring operation below 3.5V supply voltage cannot use these substitutes.

Selection between the two MCP6H04 variants depends on packaging requirements and assembly methodology rather than electrical performance.

Frequently Asked Questions (FAQ)

Q: Can MCP6H04-E/ST and MCP6H04T-E/ST be used interchangeably with TLV2404IPW?

A: Both MCP6H04 variants are electrical and mechanical equivalents for the TLV2404IPW within the constraints of the allowed parameter set. The primary difference between them is packaging format (Tube versus Tape & Reel). Electrical performance characteristics differ in slew rate, gain bandwidth product, and supply current, but these variations are within the allowed substitution parameters for this operational amplifier category.

Q: What is the key difference between MCP6H04-E/ST and MCP6H04T-E/ST?

A: The MCP6H04-E/ST is supplied in Tube packaging, while the MCP6H04T-E/ST is supplied in Tape & Reel (TR) packaging. Electrical specifications are identical between the two variants. Selection depends on assembly process requirements and inventory handling procedures.

Q: Are there supply voltage limitations when substituting with MCP6H04 parts?

A: Yes. The MCP6H04-E/ST and MCP6H04T-E/ST require a minimum supply voltage of 3.5V, whereas the TLV2404IPW operates at a minimum of 2.5V. Applications requiring operation below 3.5V supply voltage cannot use these substitutes. Both parts support the maximum 16V supply voltage.

Q: Do the substitute parts maintain the same package footprint?

A: Yes. All three parts use the 14-TSSOP package with identical dimensions (0.173", 4.40mm Width). PCB layout and footprint design remain unchanged when substituting between these parts.

Q: Are all three parts RoHS compliant?

A: Yes. The TLV2404IPW, MCP6H04-E/ST, and MCP6H04T-E/ST are all ROHS3 Compliant with Moisture Sensitivity Level 1 (Unlimited), meeting current environmental and handling standards.

Q: What performance differences exist between TLV2404IPW and the MCP6H04 substitutes?

A: The MCP6H04 variants exhibit higher slew rate (0.8V/µs versus 0.0025V/µs), higher gain bandwidth product (1.2MHz versus 5.5kHz), lower input bias current (10pA versus 100pA), and higher output current capability (50mA versus 200µA per channel). These differences indicate the MCP6H04 is optimized for higher-speed applications, while the TLV2404IPW is optimized for ultra-low-power operation.