TLE75602ESDXUMA1 Equivalent & Substitute Parts

Part Overview

The TLE75602ESDXUMA1 is an automotive-grade power management integrated circuit (PMIC) manufactured by Infineon Technologies. This device functions as a power switch/driver with 1:8 N-channel output configuration, designed for relay and solenoid driving applications. The part operates across a supply voltage range of 3V to 5.5V with load voltage capability from 3V to 28V, delivering up to 330mA per output channel. Currently in active production status with AEC-Q100 automotive qualification, this component is widely used in automotive control modules and industrial switching applications. Equivalent and substitute parts are identified based on matching electrical specifications, package compatibility, and automotive compliance certifications.

Substiute Parts

TLE75602ESDXUMA1

Infineon TechnologiesIn Stock: 3997TLE75602ESDXUMA1 Datasheet

Current PartRFQ

TLE75602ESDXUMA1

Infineon TechnologiesIn Stock: 3997TLE75602ESDXUMA1 Datasheet

Parametric EquivalentRFQ

TLE75602ESHXUMA1

Infineon TechnologiesIn Stock: 94291TLE75602ESHXUMA1 Datasheet

Parametric EquivalentRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitute parts for the TLE75602ESDXUMA1 are identified based on strict parametric equivalence across all critical electrical and mechanical specifications. The substitution logic is based on the following key parameters that must remain constant:

• Number of Outputs: 8 channels
• Ratio - Input:Output: 1:8 configuration
• Output Type: N-Channel
• Output Configuration: High Side or Low Side capability
• Interface: SPI protocol
• Voltage - Supply (Vcc/Vdd): 3V ~ 5.5V range
• Voltage - Load: 3V ~ 28V range
• Current - Output (Max): 330mA per channel
• Rds On (Typ): 1Ohm
• Features: Slew Rate Controlled
• Fault Protection: Open Loop, Over Load, Over Temperature, Over Voltage
• Operating Temperature: -40°C ~ 150°C (TJ)
• Grade: Automotive
• Qualification: AEC-Q100
• Package / Case: 24-TSSOP (0.154", 3.90mm Width) Exposed Pad
• Supplier Device Package: PG-TSDSO-24-21
• RoHS Status: ROHS3 Compliant
• Moisture Sensitivity Level (MSL): 2A (4 Weeks)
• REACH Status: REACH Unaffected

Packaging format variations (Tape & Reel versus Cut Tape & Digi-Reel) do not affect electrical or mechanical compatibility and are considered equivalent for component selection purposes.

Parameter Comparison

Engineering Selection Recommendations

Both the TLE75602ESDXUMA1 and TLE75602ESHXUMA1 are active production components manufactured by Infineon Technologies with identical electrical specifications and automotive-grade AEC-Q100 qualification. Selection between these parts is determined by packaging and supply chain requirements rather than functional capability.

The TLE75602ESDXUMA1 is supplied in Tape & Reel (TR) format with 3,955 pieces in current inventory. The TLE75602ESHXUMA1 is supplied in Cut Tape (CT) & Digi-Reel® format with 94,247 pieces in current inventory. Both parts maintain ROHS3 compliance, REACH unaffected status, and identical moisture sensitivity specifications (MSL 2A, 4 Weeks).

Component selection should be based on procurement volume requirements, assembly equipment compatibility with packaging format, and inventory availability. Both parts are suitable for direct substitution in automotive relay and solenoid driver applications requiring 8-channel N-channel power switching with SPI interface control.

Frequently Asked Questions (FAQ)

Q: Can TLE75602ESHXUMA1 be used as a direct replacement for TLE75602ESDXUMA1?

A: Yes. Both parts are parametrically equivalent across all electrical specifications, operating ranges, fault protection features, and automotive qualifications. The only difference is packaging format (Tape & Reel versus Cut Tape & Digi-Reel). Direct substitution is valid for applications where the packaging format is compatible with assembly equipment.

Q: What is the difference between Tape & Reel and Cut Tape & Digi-Reel packaging?

A: Tape & Reel (TR) format supplies components on continuous carrier tape wound on reels, suitable for high-volume automated assembly. Cut Tape (CT) & Digi-Reel format supplies pre-cut tape segments on smaller reels, suitable for lower-volume or mixed-component assembly operations. Electrical and mechanical specifications remain identical.

Q: Are both substitute parts AEC-Q100 qualified?

A: Yes. Both TLE75602ESDXUMA1 and TLE75602ESHXUMA1 carry AEC-Q100 automotive qualification and are suitable for automotive applications requiring automotive-grade components.

Q: What are the critical parameters that must match for substitution?

A: Critical parameters include 8-channel output configuration, 1:8 input-to-output ratio, N-channel output type, SPI interface, 3V to 5.5V supply voltage range, 3V to 28V load voltage range, 330mA maximum output current, 1Ohm typical on-resistance, slew rate control, comprehensive fault protection, -40°C to 150°C operating temperature range, and 24-TSSOP package format.

Q: Can these parts be used in non-automotive applications?

A: Yes. While both parts carry automotive-grade qualification and AEC-Q100 certification, they are suitable for any application requiring 8-channel N-channel power switching with the specified electrical characteristics and operating ranges.

Q: What is the moisture sensitivity level and handling requirement?

A: Both parts have MSL 2A rating with a 4-week floor life. Components must be stored in controlled humidity environments and used within the specified floor life period after packaging is opened.