TL103WID Equivalent & Substitute Parts

Part Overview

The TL103WID is a general-purpose operational amplifier manufactured by Texas Instruments, configured as a dual-channel (2 circuit) device in an 8-SOIC surface mount package. This component is classified as Last Time Buy, indicating discontinued production with limited remaining inventory (3,300 pieces). The TL103WID operates across a wide supply voltage range of 3V to 32V and is suitable for general-purpose amplification applications requiring low input bias current and moderate bandwidth performance. Identification of equivalent and substitute parts is necessary due to the Last Time Buy status and to ensure design continuity and long-term component availability.

Key Parameters

Parameter	Value	Unit
Amplifier Type	General Purpose	—
Number of Circuits	2	—
Slew Rate	0.4	V/µs
Gain Bandwidth Product	900	kHz
Current - Input Bias	20	nA
Voltage - Input Offset	1	mV
Current - Supply (per Channel)	700	µA
Current - Output / Channel	40	mA
Voltage - Supply Span (Min)	3	V
Voltage - Supply Span (Max)	32	V
Operating Temperature Range	-40 to 105	°C
Package / Case	8-SOIC (0.154", 3.90mm Width)	—
Mounting Type	Surface Mount	—
RoHS Status	ROHS3 Compliant	—
Moisture Sensitivity Level	1 (Unlimited)	—

Substitute Part Grouping Explanation

Substitute parts for the TL103WID are grouped based on strict electrical and mechanical compatibility criteria. The primary substitution parameters are:

Critical Matching Parameters:

Amplifier Type: General Purpose
Number of Circuits: 2
Package / Case: 8-SOIC (0.154", 3.90mm Width)
Mounting Type: Surface Mount
Supply Voltage Range: Minimum 3V, Maximum ≥32V
Input Bias Current: 20 nA
Output Current per Channel: 40 mA

Secondary Compatibility Parameters:

Slew Rate: 0.4 V/µs or higher
Gain Bandwidth Product: 900 kHz or higher
Input Offset Voltage: ≤2 mV
Supply Current: ≤700 µA per channel
Operating Temperature: -40°C to 105°C or wider range

Substitutes are classified into two categories:

Category 1: Direct Packaging Equivalents (Same Manufacturer) Parts with identical electrical specifications and packaging from Texas Instruments, differing only in tape/reel configuration.

Category 2: Cross-Manufacturer Substitutes Parts from alternative manufacturers (STMicroelectronics, Diodes Incorporated, Analog Devices Inc., Rohm Semiconductor) meeting or exceeding the critical electrical parameters and package requirements.

Parameter Comparison

Part Number	Manufacturer	Amplifier Type	Circuits	Slew Rate (V/µs)	GBW (kHz)	Input Bias (nA)	Input Offset (mV)	Supply Current (µA)	Output Current (mA)	Supply Min (V)	Supply Max (V)	Temp Range (°C)	Package	Status
TL103WID	Texas Instruments	General Purpose	2	0.4	900	20	1	700	40	3	32	-40 to 105	8-SOIC	Last Time Buy
TL103WIDR	Texas Instruments	General Purpose	2	0.4	900	20	1	700	40	3	32	-40 to 105	8-SOIC	Active
TSM103WID	STMicroelectronics	Amplifier	2	—	—	—	—	—	—	—	—	—	8-SOIC	Active
TSM103WIDT	STMicroelectronics	Amplifier	2	—	—	—	—	—	—	—	—	—	8-SOIC	Active
LM258ADT	STMicroelectronics	General Purpose	2	0.6	1100	20	1	700	40	3	30	-40 to 105	8-SOIC	Active
AS358AMTR-E1	Diodes Incorporated	General Purpose	2	—	—	20	2	700	40	3	36	-40 to 85	8-SOIC	Active
AS358MTR-G1	Diodes Incorporated	General Purpose	2	—	—	20	2	700	40	3	36	-40 to 85	8-SOIC	Active
BA2904YF-CE2	Rohm Semiconductor	General Purpose	2	0.2	500	20	2	500	30	3	36	-40 to 125	8-SOIC	Active
AP4310AMTR-AG1	Diodes Incorporated	General Purpose	2	0.5	1000	20	0.5	150	40	3	36	-40 to 105	8-SOIC	Active
ADA4062-2ARZ-R7	Analog Devices Inc.	J-FET	2	3.3	1400	0.002	0.75	165	20	8	36	-40 to 125	8-SOIC	Active
ADA4062-2ARZ-RL	Analog Devices Inc.	J-FET	2	3.3	1400	0.002	0.75	165	20	8	36	-40 to 125	8-SOIC	Active

Engineering Selection Recommendations

Tier 1: Recommended Direct Substitutes (Identical Electrical Performance)

TL103WIDR (Texas Instruments) is the primary recommended substitute. This part is electrically identical to the TL103WID with matching specifications across all critical parameters: 0.4 V/µs slew rate, 900 kHz gain bandwidth product, 20 nA input bias current, and 1 mV input offset voltage. The only difference is packaging format (Cut Tape & Digi-Reel® versus Tube), and the part maintains Active product status with significantly higher inventory (30,200 pieces). RoHS3 compliance and MSL 1 rating are identical.

Tier 2: High-Compatibility Cross-Manufacturer Substitutes

LM258ADT (STMicroelectronics) provides superior electrical performance with 0.6 V/µs slew rate and 1.1 MHz gain bandwidth product, exceeding TL103WID specifications. Input bias current (20 nA), input offset voltage (1 mV), and output current (40 mA) match exactly. Supply voltage range is 3V to 30V, which covers the TL103WID operating range. AEC-Q100 automotive qualification is included. Active status with 60,400 pieces in inventory.

AP4310AMTR-AG1 (Diodes Incorporated) offers enhanced performance with 0.5 V/µs slew rate and 1 MHz gain bandwidth product. Input offset voltage is superior at 0.5 mV. Supply current is significantly reduced to 150 µA per channel. Supply voltage range extends to 36V maximum. Operating temperature range matches (-40°C to 105°C). Active status with 1,390 pieces available.

Tier 3: Functional Substitutes with Parameter Trade-offs

AS358AMTR-E1 and AS358MTR-G1 (Diodes Incorporated) are general-purpose amplifiers with matching input bias current (20 nA) and output current (40 mA). Supply voltage range extends to 36V. Input offset voltage is 2 mV (higher than TL103WID). Operating temperature range is -40°C to 85°C (lower maximum). Slew rate and gain bandwidth product are not specified. Extremely high inventory availability (300,200 and 300,300 pieces respectively). Active status.

BA2904YF-CE2 (Rohm Semiconductor) is an automotive-grade general-purpose amplifier with AEC-Q100 qualification. Slew rate is 0.2 V/µs (lower than TL103WID), and gain bandwidth product is 500 kHz (lower). Supply current is reduced to 500 µA. Output current per channel is 30 mA (lower than TL103WID). Operating temperature range extends to -40°C to 125°C. Active status with 5,299 pieces in inventory.

Tier 4: Specialized Substitutes (Different Amplifier Architecture)

ADA4062-2ARZ-R7 and ADA4062-2ARZ-RL (Analog Devices Inc.) are J-FET input amplifiers with fundamentally different electrical characteristics. Input bias current is extremely low at 2 pA (versus 20 nA). Slew rate is 3.3 V/µs and gain bandwidth product is 1.4 MHz, both significantly higher. However, minimum supply voltage is 8V (versus 3V for TL103WID), which may restrict low-voltage applications. Output current per channel is 20 mA (lower than TL103WID). These parts are suitable only for applications where the higher performance and lower input bias current justify the higher minimum supply voltage requirement.

Selection Criteria Summary:

For direct replacement with maximum compatibility: Select TL103WIDR
For improved performance with automotive qualification: Select LM258ADT
For enhanced performance with reduced power consumption: Select AP4310AMTR-AG1
For high-volume applications with cost optimization: Select AS358AMTR-E1 or AS358MTR-G1
For automotive applications with extended temperature range: Select BA2904YF-CE2
For ultra-low input bias current applications: Select ADA4062-2ARZ-R7 or ADA4062-2ARZ-RL (with 8V minimum supply voltage consideration)

All recommended substitutes maintain RoHS3 compliance and are classified as Active products, ensuring long-term availability and supply chain continuity.

Frequently Asked Questions (FAQ)

Q1: Can TL103WIDR be used as a direct replacement for TL103WID?

A: Yes. TL103WIDR is electrically and functionally identical to TL103WID. Both are manufactured by Texas Instruments with matching specifications: 0.4 V/µs slew rate, 900 kHz gain bandwidth product, 20 nA input bias current, 1 mV input offset voltage, and identical supply voltage range (3V to 32V). The only difference is packaging format (Cut Tape & Digi-Reel® versus Tube). Both are RoHS3 compliant with MSL 1 rating. TL103WIDR is recommended as the primary substitute due to Active product status and higher inventory availability.

Q2: What are the key differences between general-purpose and J-FET amplifier substitutes?

A: General-purpose amplifiers (TL103WID, LM258ADT, AS358AMTR-E1, AP4310AMTR-AG1, BA2904YF-CE2) use bipolar input stages with input bias currents in the 20 nA range. J-FET amplifiers (ADA4062-2ARZ-R7, ADA4062-2ARZ-RL) use field-effect transistor input stages with extremely low input bias currents (2 pA). J-FET amplifiers offer superior input impedance and lower input bias current, but require higher minimum supply voltages (8V versus 3V). Selection depends on application requirements for input bias current and minimum supply voltage.

Q3: Is LM258ADT suitable for applications requiring 32V maximum supply voltage?

A: LM258ADT has a maximum supply voltage rating of 30V, which is 2V below the TL103WID specification of 32V. For applications requiring operation at 31V or 32V, LM258ADT is not suitable. Alternative substitutes with 32V or higher maximum supply voltage include TL103WIDR (32V), AS358AMTR-E1 (36V), AS358MTR-G1 (36V), BA2904YF-CE2 (36V), ADA4062-2ARZ-R7 (36V), and ADA4062-2ARZ-RL (36V).

Q4: Which substitute offers the lowest power consumption?

A: AP4310AMTR-AG1 offers the lowest supply current at 150 µA per channel, compared to 700 µA for TL103WID. ADA4062-2ARZ-R7 and ADA4062-2ARZ-RL also provide low supply current at 165 µA per channel. BA2904YF-CE2 provides 500 µA per channel. Selection of low-power substitutes should consider whether the minimum supply voltage requirement (8V for ADA4062 series) is compatible with the application.

Q5: Are all substitute parts RoHS3 compliant?

A: Yes. All substitute parts listed (TL103WIDR, TSM103WID, TSM103WIDT, LM258ADT, AS358AMTR-E1, AS358MTR-G1, BA2904YF-CE2, AP4310AMTR-AG1, ADA4062-2ARZ-R7, ADA4062-2ARZ-RL) are RoHS3 compliant. All are also REACH unaffected and classified under ECCN EAR99.

Q6: What is the difference between TSM103WID and TSM103WIDT packaging?

A: Both TSM103WID and TSM103WIDT are manufactured by STMicroelectronics in 8-SOIC package. TSM103WID is supplied in Tube packaging with MSL 1 (Unlimited moisture sensitivity level). TSM103WIDT is supplied in Cut Tape & Digi-Reel® packaging with MSL 3 (168 Hours moisture sensitivity level). MSL 3 requires moisture control during storage and handling. TSM103WIDT has higher inventory (19,319 pieces versus 5,300 pieces).

Q7: Can BA2904YF-CE2 be used in non-automotive applications?

A: Yes. BA2904YF-CE2 is an automotive-grade component with AEC-Q100 qualification, but it can be used in non-automotive applications. The automotive qualification indicates enhanced reliability testing and quality assurance. The part is suitable for general-purpose amplification in any application. Note that slew rate (0.2 V/µs) and gain bandwidth product (500 kHz) are lower than TL103WID, which may limit performance in high-speed applications.

Q8: What is the operating temperature range difference between substitutes?

A: TL103WID operates from -40°C to 105°C. Most substitutes match this range: TL103WIDR, LM258ADT, and AP4310AMTR-AG1. AS358AMTR-E1 and AS358MTR-G1 have a lower maximum temperature of 85°C. BA2904YF-CE2, ADA4062-2ARZ-R7, and ADA4062-2ARZ-RL extend to 125°C maximum. Selection should match application temperature requirements.

Q9: Which substitute has the lowest input offset voltage?

A: AP4310AMTR-AG1 has the lowest input offset voltage at 0.5 mV, compared to 1 mV for TL103WID. ADA4062-2ARZ-R7 and ADA4062-2ARZ-RL have 0.75 mV input offset voltage. AS358AMTR-E1, AS358MTR-G1, and BA2904YF-CE2 have 2 mV input offset voltage. Lower input offset voltage is beneficial for precision amplification applications.

Q10: Are there inventory considerations for long-term supply?

A: Yes. TL103WID is Last Time Buy with 3,300 pieces remaining. TL103WIDR (Active, 30,200 pieces) is recommended for long-term availability. AS358AMTR-E1 and AS358MTR-G1 have extremely high inventory (300,200 and 300,300 pieces respectively), ensuring long-term supply continuity. LM258ADT (60,400 pieces) and TSM103WIDT (19,319 pieces) also provide good availability. For critical applications requiring guaranteed long-term supply, AS358 series or LM258ADT are preferred.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message