Request Quote
(Ships tomorrow)
TL054ACDR Equivalent & Substitute Parts
Part Overview
The TL054ACDR is a J-FET input operational amplifier manufactured by Texas Instruments, configured as a 4-circuit linear amplifier in a 14-SOIC surface mount package. This device is classified as Active product status and operates within the LinCMOS™ series. The TL054ACDR is utilized in applications requiring low input bias current and high slew rate performance. Substitute parts are identified when original inventory is unavailable, when alternative packaging formats are required for manufacturing processes, or when extended operating temperature ranges are necessary for specific application environments.
Substiute Parts
Key Parameters
| Parameter | Value | Unit |
|---|---|---|
| Amplifier Type | J-FET | — |
| Number of Circuits | 4 | — |
| Slew Rate | 17.8 | V/µs |
| Gain Bandwidth Product | 2.7 | MHz |
| Current - Input Bias | 30 | pA |
| Voltage - Input Offset | 500 | µV |
| Current - Supply (x4 Channels) | 8.4 | mA |
| Current - Output / Channel | 80 | mA |
| Voltage - Supply Span (Min) | 10 | V |
| Voltage - Supply Span (Max) | 30 | V |
| Operating Temperature | 0 to 70 | °C |
| Package / Case | 14-SOIC (0.154", 3.90mm Width) | — |
| Mounting Type | Surface Mount | — |
| RoHS Status | ROHS3 Compliant | — |
Substitute Part Grouping Explanation
Substitute parts for the TL054ACDR are identified based on the following critical parameters that determine functional compatibility:
Primary Substitution Criteria:
- Amplifier Type (J-FET vs. General Purpose)
- Number of Circuits (4-circuit configuration)
- Slew Rate (minimum 17.8 V/µs for TL054ACDR performance class)
- Gain Bandwidth Product (minimum 2.7 MHz)
- Input Bias Current (maximum 30 pA for J-FET class)
- Supply Voltage Range (minimum 10 V to maximum 30 V overlap)
- Output Current per Channel (minimum 80 mA)
- Operating Temperature Range (0°C to 70°C minimum coverage)
- Package compatibility (14-pin configurations: 14-SOIC, 14-CERDIP, 14-PDIP)
- Mounting Type (Surface Mount or Through Hole)
Substitution Logic:
J-FET amplifiers (5962-9063301MCA, AD713AQ, AD713JNZ) are direct functional equivalents to the TL054ACDR, sharing the same amplifier topology and input characteristics. These parts maintain the 4-circuit configuration and meet or exceed the slew rate and bandwidth requirements.
General Purpose amplifiers (5962-8777101M3A, 5962-88565023A, AD704 series) represent functional alternatives when J-FET input characteristics are not mandatory. These parts offer different input bias current specifications and may be selected based on application-specific noise and offset requirements.
Package variants (14-SOIC, 14-CERDIP, 14-PDIP) are interchangeable at the functional level but require PCB layout modifications for mounting type transitions (Surface Mount to Through Hole or vice versa).
Parameter Comparison
| Parameter | TL054ACDR | 5962-9063301MCA | AD713AQ | AD713JNZ | 5962-8777101M3A | 5962-88565023A | AD704ARZ-16 | AD704JRZ-16 |
|---|---|---|---|---|---|---|---|---|
| Amplifier Type | J-FET | J-FET | J-FET | J-FET | General Purpose | General Purpose | General Purpose | General Purpose |
| Number of Circuits | 4 | 4 | 4 | 4 | 4 | 4 | 4 | 4 |
| Slew Rate (V/µs) | 17.8 | 20 | 20 | 20 | 0.15 | 8 | 0.1 | 0.1 |
| Gain Bandwidth Product (MHz) | 2.7 | 4 | 4 | 4 | 0.5 | 6.5 | 0.8 | 0.8 |
| Current - Input Bias (pA) | 30 | 10 | 10 | 10 | 750 | 7000 | 100 | 100 |
| Voltage - Input Offset (µV) | 500 | 300 | 300 | 300 | 40 | 250 | 50 | 50 |
| Current - Supply (mA) | 8.4 | 10 | 10 | 10 | 0.6 | 9.2 | 1.5 | 1.5 |
| Current - Output / Channel (mA) | 80 | 25 | 25 | 25 | — | — | 15 | 15 |
| Voltage - Supply Span Min (V) | 10 | 9 | 9 | 9 | 6 | 9 | 4 | 4 |
| Voltage - Supply Span Max (V) | 30 | 36 | 36 | 36 | 36 | 36 | 36 | 36 |
| Operating Temperature (°C) | 0 to 70 | -55 to 125 | -40 to 85 | 0 to 70 | -55 to 125 | -55 to 125 | -40 to 85 | 0 to 70 |
| Package / Case | 14-SOIC | 14-CERDIP | 14-CERDIP | 14-PDIP | 28-LCC | 28-LCC | 16-SOIC | 16-SOIC |
| Mounting Type | Surface Mount | Through Hole | Through Hole | Through Hole | Surface Mount | Surface Mount | Surface Mount | Surface Mount |
| RoHS Status | ROHS3 Compliant | ROHS3 Compliant | ROHS3 Compliant | ROHS3 Compliant | ROHS3 Compliant | ROHS3 Compliant | ROHS3 Compliant | ROHS3 Compliant |
Engineering Selection Recommendations
J-FET Amplifier Substitutes (Direct Functional Equivalents):
The parts 5962-9063301MCA, AD713AQ, and AD713JNZ are J-FET input amplifiers that maintain the same amplifier topology as the TL054ACDR. These substitutes provide equal or superior slew rate (20 V/µs vs. 17.8 V/µs) and gain bandwidth product (4 MHz vs. 2.7 MHz). Input bias current is lower (10 pA vs. 30 pA), resulting in improved input impedance characteristics. All three parts are ROHS3 Compliant and REACH Unaffected, meeting the same regulatory requirements as the TL054ACDR.
Selection between these J-FET alternatives depends on package and mounting requirements:
- 5962-9063301MCA: 14-CERDIP Through Hole package, extended temperature range (-55°C to 125°C)
- AD713AQ: 14-CERDIP Through Hole package, extended temperature range (-40°C to 85°C)
- AD713JNZ: 14-PDIP Through Hole package, standard temperature range (0°C to 70°C)
General Purpose Amplifier Alternatives:
The AD704 series (AD704ARZ-16, AD704JRZ-16) and 5962-88565023A represent functional alternatives when J-FET input characteristics are not required. These parts offer lower input offset voltage (50 µV vs. 500 µV) and reduced supply current (1.5 mA vs. 8.4 mA). However, output current per channel is reduced (15 mA vs. 80 mA), and slew rate is significantly lower (0.1 V/µs vs. 17.8 V/µs). These parts are suitable for applications prioritizing low power consumption and precision offset characteristics over high-speed performance.
The 5962-8777101M3A is a General Purpose amplifier with differential output configuration in a 28-LCC package. This part exhibits significantly lower slew rate (0.15 V/µs) and bandwidth (500 kHz), making it unsuitable for high-speed applications but suitable for precision instrumentation requiring extended temperature operation (-55°C to 125°C).
Compliance and Regulatory Status:
All substitute parts listed maintain ROHS3 Compliance and REACH Unaffected status, ensuring compatibility with current environmental and regulatory requirements. Moisture Sensitivity Level (MSL) is 1 (Unlimited) for all parts, indicating no special moisture handling requirements during storage or assembly.
Frequently Asked Questions (FAQ)
Q: Can the TL054ACDR be directly replaced with AD704ARZ-16 in a 1:1 substitution?
A: Direct 1:1 substitution is not recommended. While both are 4-circuit operational amplifiers, the AD704ARZ-16 is a General Purpose amplifier with significantly different performance characteristics. The AD704ARZ-16 has a slew rate of 0.1 V/µs compared to the TL054ACDR's 17.8 V/µs, and output current per channel is 15 mA versus 80 mA. These differences make the AD704ARZ-16 unsuitable for applications requiring high-speed signal processing. Substitution is only valid if the application does not require the TL054ACDR's high slew rate and output current capabilities.
Q: What is the difference between 14-SOIC, 14-CERDIP, and 14-PDIP packages?
A: These are three different 14-pin package formats with different physical dimensions and mounting methods. The 14-SOIC (Small Outline Integrated Circuit) is a surface mount package with 0.154" width. The 14-CERDIP (Ceramic Dual In-line Package) and 14-PDIP (Plastic Dual In-line Package) are through-hole packages with 0.300" width and 7.62mm spacing. Transitioning between surface mount (14-SOIC) and through-hole packages (14-CERDIP, 14-PDIP) requires PCB redesign and cannot be accomplished through component substitution alone.
Q: Are the J-FET substitutes (5962-9063301MCA, AD713AQ, AD713JNZ) fully compatible with the TL054ACDR?
A: The J-FET substitutes are functionally compatible at the circuit level, sharing the same amplifier topology and input characteristics. All three parts maintain 4-circuit configuration, J-FET input stage, and meet or exceed the TL054ACDR's slew rate and bandwidth specifications. However, package differences require PCB layout modifications. The 5962-9063301MCA and AD713AQ use 14-CERDIP packages, while AD713JNZ uses 14-PDIP. These through-hole packages cannot be directly mounted on PCBs designed for the 14-SOIC surface mount package.
Q: Why does the TL054ACDR have higher output current (80 mA) compared to J-FET substitutes (25 mA)?
A: Output current capability is determined by the internal output stage design and is a specified parameter for each device. The TL054ACDR is designed for applications requiring higher output current drive capability. When selecting a substitute, verify that the application's output current requirements do not exceed the substitute part's rated output current per channel. If higher output current is required, the J-FET substitutes may not be suitable.
Q: Can the TL054ACDR be used in applications requiring -55°C to 125°C operating temperature?
A: No. The TL054ACDR is rated for 0°C to 70°C operating temperature. For extended temperature range applications, substitute parts such as 5962-9063301MCA (-55°C to 125°C) or AD713AQ (-40°C to 85°C) must be selected. These substitutes maintain J-FET input characteristics while providing wider temperature coverage.
Q: What is the significance of the 30 pA input bias current specification for the TL054ACDR?
A: Input bias current of 30 pA indicates the leakage current flowing into the amplifier's input terminals when no signal is applied. This specification is critical for high-impedance input applications. The J-FET substitutes (5962-9063301MCA, AD713AQ, AD713JNZ) have lower input bias current (10 pA), providing superior input impedance. General Purpose substitutes (AD704 series) have higher input bias current (100 pA), which may introduce additional noise and offset in high-impedance circuits.
Q: Are all substitute parts ROHS3 Compliant?
A: Yes. All substitute parts listed in this reference document are ROHS3 Compliant and REACH Unaffected, meeting current environmental and regulatory requirements for electronic component manufacturing and use.
Alternative Parts
SJ6012L2TP
Littelfuse Inc.
6 Alternative Parts
JMK107BBJ476MA-RE
Taiyo Yuden
10 Alternative Parts
GMK107BBJ475MA-T
Taiyo Yuden
5 Alternative Parts
SJ6020N2ARP
Littelfuse Inc.
3 Alternative Parts
SJ6025R2ATP
Littelfuse Inc.
4 Alternative Parts
2474-05L
API Delevan Inc.
1 Alternative Parts
4590R-684K
API Delevan Inc.
1 Alternative Parts
CM6560R-334
API Delevan Inc.
1 Alternative Parts
CM6460-104
API Delevan Inc.
1 Alternative Parts
5526-12
API Delevan Inc.
1 Alternative Parts