SS12L RVG Equivalent & Substitute Parts

Part Overview

The SS12L RVG is a Schottky rectifier diode manufactured by Taiwan Semiconductor Corporation, rated for 20 V DC reverse voltage and 1 A average rectified current in a Sub SMA surface mount package (DO-219AB). This component is classified as Active product status and is fully RoHS3 compliant with REACH unaffected designation.

Substitute parts are identified when equivalent electrical performance and mechanical compatibility are maintained across the specified parameter set. The SS12L RVG operates within defined voltage, current, and thermal boundaries that establish the basis for component interchangeability in circuit applications.

Key Parameters

Parameter	Value	Unit
Voltage - DC Reverse (Vr) (Max)	20	V
Current - Average Rectified (Io)	1	A
Voltage - Forward (Vf) (Max) @ If	450 mV @ 1 A	mV
Speed	Fast Recovery ≤ 500ns, > 200mA (Io)	ns
Current - Reverse Leakage @ Vr	400	µA @ 20 V
Package / Case	DO-219AB	—
Mounting Type	Surface Mount	—
Operating Temperature - Junction	-55 to 125	°C
Technology	Schottky	—
RoHS Status	ROHS3 Compliant	—

Substitute Part Grouping Explanation

Substitution eligibility for the SS12L RVG is determined by strict equivalence across the following critical parameters:

Voltage Rating: All substitute parts must maintain a DC reverse voltage (Vr) rating of 20 V or greater to ensure safe operation within the original circuit design envelope.

Current Rating: Average rectified current (Io) must be rated at 1 A or higher to support the specified load without thermal or reliability degradation.

Package Compatibility: All substitute parts must use the DO-219AB (Sub SMA) surface mount package to ensure mechanical fit and PCB assembly compatibility without design modification.

Technology: Schottky diode technology is required to maintain fast recovery characteristics and forward voltage performance consistent with the original design.

Thermal Range: Operating junction temperature range must encompass the -55°C to 125°C specification to ensure functionality across the intended application environment.

Compliance: RoHS3 compliance and REACH unaffected status are mandatory for regulatory and supply chain continuity.

Substitute parts are grouped into two categories: parametric equivalents (identical electrical specifications) and similar parts (enhanced or equivalent performance within the same package family).

Parameter Comparison

Parameter	SS12L RVG (Main)	SS12L (Parametric Equivalent)	SL02-GS08 (Similar)
Manufacturer	Taiwan Semiconductor Corporation	Taiwan Semiconductor Corporation	Vishay General Semiconductor - Diodes Division
Voltage - DC Reverse (Vr) (Max)	20 V	20 V	20 V
Current - Average Rectified (Io)	1 A	1 A	1.1 A
Voltage - Forward (Vf) (Max) @ If	450 mV @ 1 A	450 mV @ 1 A	420 mV @ 1.1 A
Speed	Fast Recovery ≤ 500ns, > 200mA (Io)	Fast Recovery ≤ 500ns, > 200mA (Io)	Fast Recovery ≤ 500ns, > 200mA (Io)
Current - Reverse Leakage @ Vr	400 µA @ 20 V	400 µA @ 20 V	250 µA @ 20 V
Reverse Recovery Time (trr)	—	—	10 ns
Package / Case	DO-219AB	DO-219AB	DO-219AB
Mounting Type	Surface Mount	Surface Mount	Surface Mount
Operating Temperature - Junction	-55 to 125°C	-55 to 125°C	125°C (Max)
Technology	Schottky	Schottky	Schottky
RoHS Status	ROHS3 Compliant	ROHS3 Compliant	ROHS3 Compliant
Product Status	Active	Not For New Designs	Active

Engineering Selection Recommendations

SS12L (Parametric Equivalent): This part maintains identical electrical specifications to the SS12L RVG across all critical parameters. However, the product status is classified as "Not For New Designs," indicating that this variant is in end-of-life phase. Selection of this substitute is appropriate only for legacy system maintenance, repair, or continuation of existing production runs where design change is not feasible. For new circuit designs, this part should not be selected.

SL02-GS08 (Similar Substitute): This Vishay General Semiconductor part is classified as Active product status and is suitable for new designs. The SL02-GS08 provides enhanced performance characteristics: current rating increased to 1.1 A (10% margin above the 1 A requirement), forward voltage reduced to 420 mV (30 mV improvement), and reverse leakage current reduced to 250 µA (150 µA improvement). All parameters meet or exceed the SS12L RVG specification envelope. The DO-219AB package ensures mechanical compatibility without PCB redesign. RoHS3 compliance and REACH unaffected status are maintained. The SL02-GS08 is the preferred substitute for new designs and production transitions.

Both substitute parts are compliant with regulatory requirements and maintain the same surface mount package footprint. Selection between them depends on product lifecycle status and design phase requirements.

Frequently Asked Questions (FAQ)

Q: Can the SS12L (Parametric Equivalent) be used as a direct replacement for the SS12L RVG?

A: Electrical and mechanical compatibility is confirmed. However, the SS12L is designated "Not For New Designs." Direct replacement is permissible for maintenance and repair of existing systems. For new circuit development, alternative parts should be evaluated.

Q: What are the advantages of the SL02-GS08 over the SS12L RVG?

A: The SL02-GS08 offers three measurable improvements: 10% higher current rating (1.1 A vs. 1 A), lower forward voltage drop (420 mV vs. 450 mV), and reduced reverse leakage current (250 µA vs. 400 µA). These characteristics provide enhanced thermal efficiency and lower power dissipation. The SL02-GS08 maintains Active product status, supporting long-term supply chain availability.

Q: Are all substitute parts compatible with the existing PCB layout?

A: Yes. All substitute parts use the DO-219AB (Sub SMA) surface mount package, which maintains identical footprint and land pattern geometry. No PCB redesign is required for mechanical compatibility.

Q: Do the substitute parts meet the same compliance standards as the SS12L RVG?

A: Yes. Both the SS12L and SL02-GS08 are RoHS3 compliant and REACH unaffected, matching the regulatory status of the SS12L RVG.

Q: What is the operating temperature range for each substitute part?

A: The SS12L (Parametric Equivalent) maintains the full -55°C to 125°C junction temperature range. The SL02-GS08 specifies a maximum junction temperature of 125°C. For applications requiring the full lower temperature range, the SS12L is appropriate. For standard commercial and industrial applications operating above -55°C, the SL02-GS08 is suitable.

Q: Can the SL02-GS08 be used in applications where the SS12L RVG was originally specified?

A: Yes. The SL02-GS08 meets or exceeds all critical electrical parameters of the SS12L RVG. The enhanced current rating, improved forward voltage, and reduced leakage current provide equivalent or superior performance. The part is suitable for direct substitution in existing circuit designs.

Q: What is the difference between "Parametric Equivalent" and "Similar" substitute classifications?

A: A parametric equivalent maintains identical electrical specifications across all measured parameters. A similar substitute meets the same functional requirements and package compatibility but may offer enhanced performance characteristics. Both classifications confirm substitution eligibility based on the specified parameter set.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message