SS11VL-R06270 Equivalent & Substitute Parts

Part Overview

The SS11VL-R06270 is a 2-line common mode choke (CMC) manufactured by KEMET, designed for power line filtering applications. This through-hole component operates at 27 mH inductance @ 1 kHz with a maximum current rating of 600 mA and DC resistance of 1.3 Ohm. The part is Active in product status and fully compliant with RoHS3 and REACH regulations. Substitute parts are identified when design requirements permit variation in inductance value, current rating, or physical dimensions while maintaining core electrical and mechanical compatibility within the 2-line common mode choke category.

Substiute Parts

SS11VL-R06270

KEMETIn Stock: 1334SS11VL-R06270 Datasheet

Current PartRFQ

SS11VL-06180

KEMETIn Stock: 2129SS11VL-06180 Datasheet

Parametric EquivalentRFQ

SS21V-R060330

KEMETIn Stock: 1774SS21V-R060330 Datasheet

Parametric EquivalentRFQ

SS21V-R070260

KEMETIn Stock: 1331SS21V-R070260 Datasheet

Parametric EquivalentRFQ

SU10VFC-R07088

KEMETIn Stock: 1500SU10VFC-R07088 Datasheet

Parametric EquivalentRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitute parts for the SS11VL-R06270 are classified based on the following substitution criteria:

Primary Compatibility Parameters:

• Filter Type: Power Line
• Number of Lines: 2
• Mounting Type: Through Hole
• Package / Case: Vertical, 4 PC Pin
• Voltage Rating - AC: 250 V
• Operating Temperature: -25°C ~ 120°C
• RoHS Status: RoHS3 Compliant
• REACH Status: REACH Unaffected
• Product Status: Active

Variable Parameters Permitting Substitution:

• Inductance @ Frequency (range: 8.8 mH to 33 mH @ 1 kHz)
• Current Rating (Max) (range: 600 mA to 700 mA)
• DC Resistance (DCR) (Max) (range: 1.1 Ohm to 1.5 Ohm)
• Physical Dimensions (within through-hole vertical package constraints)

Substitutes are valid when the application requirements allow tolerance in inductance value and current capacity. All substitute parts maintain identical filter type, line configuration, mounting method, voltage rating, temperature range, and regulatory compliance status.

Parameter Comparison

Engineering Selection Recommendations

All substitute parts listed maintain Active product status and full compliance with RoHS3 and REACH regulations, ensuring regulatory continuity in design implementations.

SS11VL-06180: Identical physical dimensions and pin configuration to the main part. Inductance reduced to 18 mH @ 1 kHz with matching 600 mA current rating and 1.3 Ohm DCR. Suitable for applications requiring lower inductance filtering within the same footprint.

SS21V-R060330: Increased inductance to 33 mH @ 1 kHz with slightly elevated DCR of 1.5 Ohm. Physical dimensions increase to 20.50 mm L x 16.50 mm W with 24.50 mm height. Current rating remains 600 mA. Applicable when higher inductance filtering is required and PCB layout accommodates larger component footprint.

SS21V-R070260: Inductance of 26 mH @ 1 kHz closely matches the main part specification. Current rating increases to 700 mA with reduced DCR of 1.1 Ohm. Physical dimensions match SS21V-R060330 series. Suitable for applications requiring higher current capacity with improved thermal performance.

SU10VFC-R07088: Lowest inductance at 8.8 mH @ 1 kHz with 700 mA current rating and 1.1 Ohm DCR. Smallest physical footprint at 18.00 mm L x 15.50 mm W and 15.00 mm height. Applicable for space-constrained designs or applications requiring minimal inductance filtering.

Frequently Asked Questions (FAQ)

Q: Can SS11VL-06180 directly replace SS11VL-R06270 in my circuit?

A: Direct replacement is possible if your circuit design permits operation at 18 mH inductance instead of 27 mH. Both parts share identical physical dimensions, pin configuration, current rating, and DCR specifications. Verify that the reduced inductance value meets your filtering requirements.

Q: What is the primary difference between SS21V-R060330 and SS21V-R070260?

A: SS21V-R060330 provides 33 mH inductance at 600 mA current rating with 1.5 Ohm DCR. SS21V-R070260 provides 26 mH inductance at 700 mA current rating with 1.1 Ohm DCR. Selection depends on whether your application prioritizes higher inductance filtering or higher current capacity with lower resistance.

Q: Will SU10VFC-R07088 fit in the same PCB location as SS11VL-R06270?

A: No. SU10VFC-R07088 has a smaller footprint (18.00 mm L x 15.50 mm W x 15.00 mm height) compared to SS11VL-R06270 (22.00 mm L x 14.50 mm W x 19.50 mm height). While the component will physically fit in a larger space, PCB layout modifications are required if the original design was optimized for the larger SS11VL dimensions.

Q: Are all substitute parts RoHS3 and REACH compliant?

A: Yes. All substitute parts listed are RoHS3 Compliant and REACH Unaffected, maintaining regulatory compliance equivalent to the main part SS11VL-R06270.

Q: What inductance range is available across all substitute options?

A: Inductance values range from 8.8 mH (SU10VFC-R07088) to 33 mH (SS21V-R060330) @ 1 kHz. The main part SS11VL-R06270 operates at 27 mH, with SS21V-R070260 providing the closest alternative at 26 mH.

Q: Can I use a substitute part with higher current rating in a 600 mA application?

A: Yes. Parts rated for 700 mA (SS21V-R070260 and SU10VFC-R07088) are suitable for applications requiring 600 mA or less. The higher current rating provides design margin and improved thermal performance due to lower DCR values in these parts.

Q: How do physical dimensions affect substitution decisions?

A: Physical dimensions determine PCB layout compatibility. SS11VL-06180 matches the main part exactly. SS21V series parts are larger (20.50 mm L x 16.50 mm W x 24.50 mm height). SU10VFC-R07088 is smallest. Verify available PCB space before selecting a substitute with different dimensions.