SN65MLVD200ADRG4 Equivalent & Substitute Parts

Part Overview

The SN65MLVD200ADRG4 is a 1/1 transceiver half LVDS multipoint interface IC in 8-SOIC packaging manufactured by Texas Instruments. This part is discontinued at DiGi Electronics, necessitating identification of equivalent and substitute components for ongoing design support and production requirements. The device operates at 3V to 3.6V supply voltage with a 100 Mbps data rate and supports half-duplex LVDS communication with 25 mV receiver hysteresis across the -40°C to 85°C operating temperature range.

Key Parameters

Parameter	Value
Type	Transceiver
Protocol	LVDS, Multipoint
Number of Drivers/Receivers	1/1
Duplex	Half
Data Rate	100 Mbps
Voltage - Supply	3V ~ 3.6V
Operating Temperature	-40°C ~ 85°C
Package / Case	8-SOIC (0.154", 3.90mm Width)
Receiver Hysteresis	25 mV
RoHS Status	ROHS3 Compliant
Moisture Sensitivity Level	1 (Unlimited)

Substitute Part Grouping Explanation

Substitution for the SN65MLVD200ADRG4 is determined by strict alignment of the following critical parameters: protocol type (LVDS, Multipoint), driver/receiver configuration (1/1), duplex mode (Half), package format (8-SOIC), supply voltage range (3V ~ 3.6V), operating temperature range (-40°C ~ 85°C), and data rate capability (100 Mbps minimum). Parts are grouped into two categories:

Parametric Equivalents (Texas Instruments SN65MLVD Series): SN65MLVD200ADR, SN65MLVD204ADR, and SN65MLVD204DR maintain identical electrical specifications and package format. These parts differ only in product status and packaging configuration (Cut Tape/Digi-Reel versus Digi-Reel only).

Manufacturer Recommended Alternatives: NB3N200SDR2G (onsemi), SP3494EN-L (MaxLinear), and SP483EEN-L/TR (MaxLinear) are listed as manufacturer-recommended substitutes but operate under different protocols or specifications. These require application-level compatibility verification due to protocol differences (Clock Buffer or RS422/RS485 versus LVDS).

Parameter Comparison

Part Number	Manufacturer	Protocol	Drivers/Receivers	Data Rate	Supply Voltage	Package	Product Status	Inventory
SN65MLVD200ADRG4	Texas Instruments	LVDS, Multipoint	1/1	100 Mbps	3V ~ 3.6V	8-SOIC	Discontinued at DiGi Electronics	930 Pcs
SN65MLVD200ADR	Texas Instruments	LVDS, Multipoint	1/1	100 Mbps	3V ~ 3.6V	8-SOIC	Active	1900 Pcs
SN65MLVD204ADR	Texas Instruments	LVDS, Multipoint	1/1	100 Mbps	3V ~ 3.6V	8-SOIC	Active	7723 Pcs
SN65MLVD204DR	Texas Instruments	LVDS, Multipoint	1/1	100 Mbps	3V ~ 3.6V	8-SOIC	Not For New Designs	3460 Pcs
NB3N200SDR2G	onsemi	LVCMOS/LVDS Buffer	1:1 Ratio	200 MHz	3V ~ 3.6V	8-SOIC	Active	869 Pcs
SP3494EN-L	MaxLinear, Inc.	RS422, RS485	1/1	2.5 Mbps	3V ~ 3.6V	8-SOIC	Active	1175 Pcs
SP483EEN-L/TR	MaxLinear, Inc.	RS422, RS485	1/1	250 kbps	4.75V ~ 5.25V	8-SOIC	Active	35400 Pcs

Engineering Selection Recommendations

Primary Substitutes (Direct Replacement): SN65MLVD200ADR and SN65MLVD204ADR are the preferred direct replacements. Both are active products from Texas Instruments with identical electrical specifications to the SN65MLVD200ADRG4. SN65MLVD204ADR offers the highest current inventory (7723 units) and is recommended for new procurement. SN65MLVD200ADR provides an alternative with 1900 units in stock.

Secondary Substitute (Legacy Status): SN65MLVD204DR maintains full electrical compatibility but carries "Not For New Designs" status. This part is suitable only for legacy system maintenance or repair applications where design changes are not feasible.

Alternative Protocol Substitutes (Application-Dependent): NB3N200SDR2G, SP3494EN-L, and SP483EEN-L/TR are manufacturer-recommended alternatives but operate under different protocols (Clock Buffer or RS422/RS485). These parts are suitable only for applications where protocol conversion or functional equivalence has been validated at the system level. SP483EEN-L/TR operates at 4.75V to 5.25V supply voltage, requiring voltage regulation modifications for 3V to 3.6V systems.

All recommended substitutes maintain ROHS3 compliance, MSL Level 1 rating, and -40°C to 85°C operating temperature range.

Frequently Asked Questions (FAQ)

Q: Can SN65MLVD200ADR directly replace SN65MLVD200ADRG4? A: Yes. SN65MLVD200ADR is a direct parametric equivalent with identical electrical specifications, protocol support (LVDS Multipoint), 1/1 driver/receiver configuration, 100 Mbps data rate, 3V to 3.6V supply voltage, and 8-SOIC package. The primary difference is product status (Active versus Discontinued) and packaging format (Cut Tape/Digi-Reel availability).

Q: What is the difference between SN65MLVD200ADR and SN65MLVD204ADR? A: Both parts are parametric equivalents with identical electrical specifications and package format. The difference lies in the base product number designation (65MLVD200 versus 65MLVD204). SN65MLVD204ADR offers higher inventory availability (7723 units) and is the recommended choice for new procurement.

Q: Can NB3N200SDR2G replace the SN65MLVD200ADRG4? A: NB3N200SDR2G is a clock buffer/driver with LVCMOS and LVDS input/output capability, not a dedicated LVDS transceiver. While it operates at the same supply voltage (3V to 3.6V) and package format (8-SOIC), it functions as a 1:1 buffer rather than a 1/1 transceiver. Substitution requires application-level validation to confirm functional equivalence.

Q: Why are SP3494EN-L and SP483EEN-L/TR listed as substitutes if they use different protocols? A: These MaxLinear parts are manufacturer-recommended alternatives for applications requiring RS422/RS485 protocol support instead of LVDS. SP483EEN-L/TR operates at 4.75V to 5.25V supply voltage, requiring external voltage regulation for 3V to 3.6V systems. Substitution is application-dependent and requires system-level compatibility verification.

Q: What packaging options are available for the substitute parts? A: All substitute parts are available in 8-SOIC (0.154", 3.90mm Width) surface mount package, matching the original SN65MLVD200ADRG4 footprint. Packaging configurations vary: SN65MLVD200ADR and SN65MLVD204ADR are available in Cut Tape and Digi-Reel formats; SN65MLVD204DR is Digi-Reel only; NB3N200SDR2G is Tape & Reel; SP3494EN-L is Tube; SP483EEN-L/TR is Cut Tape and Digi-Reel.

Q: Are all substitute parts RoHS3 compliant? A: Yes. All listed substitute parts maintain ROHS3 compliance and MSL Level 1 (Unlimited) moisture sensitivity rating, matching the original part's environmental certifications.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message