SLP272M063C5P3

Part Overview

The SLP272M063C5P3 is a 2700 µF, 63 V aluminum electrolytic capacitor manufactured by Cornell Dubilier Electronics (CDE) in a radial, can snap-in package configuration. This capacitor is classified as Active product status and serves general-purpose applications requiring bulk energy storage and filtering in power supply circuits. Alternative part models may be necessary due to inventory constraints, specific supply chain requirements, or application-specific performance needs while maintaining electrical and mechanical compatibility.

Substiute Parts

SLP272M063C5P3

Cornell Dubilier Electronics (CDE)In Stock: 920SLP272M063C5P3 Datasheet

Current PartRFQ

381LX272M063H042

Cornell Dubilier Electronics (CDE)In Stock: 4185381LX272M063H042 Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

The substitute part 381LX272M063H042 qualifies as a direct electrical and mechanical equivalent based on the following matching parameters:

• Capacitance: 2700 µF (identical)
• Voltage Rating: 63 V (identical)
• Tolerance: ±20% (identical)
• Lifetime @ 105°C: 3000 Hrs (identical)
• Operating Temperature Range: -40°C to 105°C (identical)
• Ripple Current @ 120 Hz: 2.2 A (identical)
• Package Configuration: Radial, Can - Snap-In Through Hole (identical)
• RoHS Status: ROHS3 Compliant (identical)
• MSL Rating: 1 (Unlimited) (identical)
• Lead Spacing: 0.394" (10.00mm) (identical)

Substitution is validated by matching electrical ratings, temperature characteristics, and mechanical form factors. The 381LX272M063H042 maintains all critical performance parameters necessary for seamless integration into applications designed for the SLP272M063C5P3.

Parameter Comparison

Engineering Selection Recommendations

Both SLP272M063C5P3 and 381LX272M063H042 are Active products manufactured by Cornell Dubilier Electronics with ROHS3 compliance and identical environmental ratings. Selection between these parts should be based on:

• Mechanical Fit: Physical dimension differences exist (diameter and height). Verify PCB layout and chassis clearance accommodate the 381LX272M063H042 dimensions (0.866" diameter, 1.654" height) versus the SLP272M063C5P3 (0.984" diameter, 1.378" height).
• High-Frequency Performance: At 20 kHz ripple current, the 381LX272M063H042 is rated at 2.5 A compared to 2.75 A for the SLP272M063C5P3. Application-specific ripple current demands must be evaluated.
• Inventory Availability: The 381LX272M063H042 provides significantly higher stock availability (4092 pieces versus 860 pieces).
• Regulatory Compliance: Both parts satisfy ROHS3 and REACH requirements for regulated markets.

Frequently Asked Questions (FAQ)

Q: Can I use the 381LX272M063H042 as a direct replacement for the SLP272M063C5P3? A: Electrical substitution is valid when ripple current requirements do not exceed 2.5 A @ 20 kHz. Mechanical fit must be verified due to dimensional differences in diameter and height.

Q: What are the key differences between these capacitors? A: Both parts share identical capacitance (2700 µF), voltage rating (63 V), tolerance (±20%), temperature range (-40°C to 105°C), and lifetime (3000 Hrs @ 105°C). The 381LX272M063H042 has a smaller diameter (22.00mm vs 25.00mm) but greater height (42.00mm vs 35.00mm), and lower high-frequency ripple current rating (2.5 A vs 2.75 A @ 20 kHz).

Q: Are there any compliance or certification concerns? A: No. Both parts are ROHS3 compliant and REACH unaffected, suitable for applications in regulated markets.

Q: How should I select between these two parts? A: Selection depends on three criteria: physical space constraints on your PCB, high-frequency ripple current demands of your circuit, and supply chain requirements. If space permits the 381LX272M063H042 geometry and your ripple current stays below 2.5 A @ 20 kHz, either part is suitable.

Q: What happens if my circuit requires the higher ripple current rating of the SLP272M063C5P3? A: Use the SLP272M063C5P3 if your application demands ripple current handling at 2.75 A @ 20 kHz, as the 381LX272M063H042 is specified only to 2.5 A at this frequency.