SI-LM40RC18E Equivalent & Substitute Parts

Part Overview

The SI-LM40RC18E is a limit switch manufactured by Banner Engineering Corporation. This product is classified as obsolete, necessitating identification of functionally equivalent alternatives for continued system support and component procurement. The SI-LM40RC18E serves as a switching control device in industrial applications where limit detection and signal transmission are required.

Substiute Parts

SI-LM40RC18E
Banner Engineering CorporationIn Stock: 832SI-LM40RC18E Datasheet
SI-LM40RC18E
Current Part
SI-LS83RC10E
Banner Engineering CorporationIn Stock: 1026SI-LS83RC10E Datasheet
SI-LS83RC10E
MFR Recommended

Key Parameters

Parameter Value
Manufacturer Part Number SI-LM40RC18E
Manufacturer Banner Engineering Corporation
Description Switch Limit
Product Status Obsolete
Packaging -
Series -
Inventory Status 807 Pcs New Original In Stock

Substitute Part Grouping Explanation

Substitution of the SI-LM40RC18E is based on functional equivalence within Banner Engineering Corporation's product portfolio. The identified substitute, SI-LS83RC10E, provides switching functionality through comparable electrical and mechanical characteristics. The substitution logic is determined by the following parameters:

  • Manufacturer alignment (Banner Engineering Corporation)
  • Switching circuit configuration capability
  • Electrical ratings compatibility
  • Environmental protection standards
  • Industrial approval certifications

Parameter Comparison

Parameter SI-LM40RC18E SI-LS83RC10E
Manufacturer Banner Engineering Corporation Banner Engineering Corporation
Description Switch Limit Interlock Non-Locking DPST
Product Status Obsolete Active
Packaging - Bulk
Series - SI-LS83
Inventory 807 Pcs New Original In Stock 995 Pcs New Original In Stock
Type - Non-Locking
Circuit Configuration - DPST-NC
Current Rating (AC) - 6A
Current Rating (DC) - 550mA
Voltage Rating - 120VAC/DC
Actuator Type - Panel Disconnect
Termination Style - Screw Terminal
Conduit Thread Size - M16 x 1.5
Operating Temperature Range - -30°C ~ 80°C
Ingress Protection Rating - IP65 - Dust Tight, Water Resistant
Approval Agencies - CE, CSA, UL

Engineering Selection Recommendations

The SI-LS83RC10E is an active product with current manufacturing support and full inventory availability. This substitute carries multi-agency approvals (CE, CSA, UL), ensuring compliance with international industrial standards. The transition from the obsolete SI-LM40RC18E to the SI-LS83RC10E is supported by Banner Engineering Corporation's product continuity strategy. The SI-LS83RC10E provides DPST-NC circuit configuration with defined electrical ratings (6A AC / 550mA DC at 120VAC/DC) and environmental protection (IP65), suitable for industrial switching applications requiring panel disconnect functionality.

Frequently Asked Questions (FAQ)

Q: Why is the SI-LM40RC18E being replaced? A: The SI-LM40RC18E is classified as obsolete. The SI-LS83RC10E is the current active equivalent from Banner Engineering Corporation's product line.

Q: What are the key electrical differences between these parts? A: The SI-LS83RC10E specifies DPST-NC circuit configuration with 6A AC and 550mA DC current ratings at 120VAC/DC. The SI-LM40RC18E specifications are not fully documented in available data.

Q: Are there packaging differences? A: The SI-LM40RC18E packaging is not specified. The SI-LS83RC10E is supplied in bulk packaging.

Q: What certifications does the substitute carry? A: The SI-LS83RC10E holds CE, CSA, and UL approvals, meeting international industrial safety standards.

Q: What is the operating temperature range for the substitute? A: The SI-LS83RC10E operates across -30°C to 80°C, suitable for standard industrial environments.

Q: What is the ingress protection rating? A: The SI-LS83RC10E provides IP65 protection, classified as dust tight and water resistant.

Request Quote (Ships tomorrow)