S6010DRP Equivalent & Substitute Parts

Part Overview

The S6010DRP is a 600V, 10A standard recovery SCR (silicon-controlled rectifier) in TO-252 (DPAK) surface mount packaging manufactured by Littelfuse Inc. This thyristor is designed for AC switching and control applications requiring reliable gate triggering and thermal performance across industrial temperature ranges. The part is currently active in production with 5200 units in stock.

Equivalent and substitute parts are identified to support design flexibility, supply chain continuity, and application-specific performance requirements. Substitutes are selected based on matching voltage ratings, package compatibility, and on-state current capabilities within the TO-252 form factor.

Substiute Parts

S6010DRP

Littelfuse Inc.In Stock: 5283S6010DRP Datasheet

Current PartRFQ

MCR12DCMT4G

Littelfuse Inc.In Stock: 10204MCR12DCMT4G Datasheet

MFR RecommendedRFQ

MCR12DSMT4G

Littelfuse Inc.In Stock: 16834MCR12DSMT4G Datasheet

MFR RecommendedRFQ

MCR8DCMT4G

Littelfuse Inc.In Stock: 10478MCR8DCMT4G Datasheet

MFR RecommendedRFQ

S6006DRP

Littelfuse Inc.In Stock: 2910S6006DRP Datasheet

Parametric EquivalentRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the S6010DRP is determined by the following criteria:

Mandatory Matching Parameters:

• Voltage - Off State: 600V
• Package / Case: TO-252-3, DPAK (2 Leads + Tab)
• Mounting Type: Surface Mount
• RoHS Status: ROHS3 Compliant

Current Rating Flexibility: Substitute parts may have equal or higher on-state RMS current ratings (It RMS ≥ 10A) while maintaining the same voltage class and package. This allows for thermal margin and application headroom.

Gate Characteristics: Gate trigger voltage (Vgt) and current (Igt) may vary between standard recovery and sensitive gate variants. Sensitive gate types feature lower trigger current requirements, enabling operation with reduced gate drive circuits.

SCR Type Variants: Standard recovery SCRs are primary substitutes. Sensitive gate variants (MCR12DSMT4G) are included as alternatives for applications requiring minimal gate drive power.

Parameter Comparison

Engineering Selection Recommendations

MCR12DCMT4G (MFR Recommended): This standard recovery SCR provides 12A on-state current capability, exceeding the S6010DRP's 10A rating. It maintains identical voltage class, package, and operating temperature range. ROHS3 compliance and REACH unaffected status ensure regulatory alignment. Suitable for direct substitution in applications requiring equal or higher current capacity.

MCR12DSMT4G (Sensitive Gate Variant): This sensitive gate SCR reduces gate trigger current to 200µA, compared to 15mA for the S6010DRP. Operating temperature range is -40°C to 110°C. ROHS3 compliant with REACH affected status. Select this variant only when gate drive power minimization is a design requirement and the reduced upper temperature limit (-110°C vs -125°C) is acceptable.

MCR8DCMT4G (Lower Current Rating): This standard recovery SCR provides 8A on-state current, below the S6010DRP's 10A rating. Use only in applications where the lower current capacity is sufficient and thermal margin is not critical. Maintains full voltage class, package compatibility, and operating temperature range.

S6006DRP (Parametric Equivalent): This standard recovery SCR provides 6A on-state current with matching gate characteristics (Vgt 1.5V, Igt 15mA) to the S6010DRP. Use only in applications where 6A current capacity is adequate. REACH affected status requires verification for regulated end-use applications.

Frequently Asked Questions (FAQ)

Q: Can MCR12DCMT4G replace S6010DRP in all applications? A: MCR12DCMT4G is a direct substitute for applications where 12A on-state current capacity meets or exceeds design requirements. The higher current rating provides thermal margin. Verify gate drive circuit compatibility, as Vgt is reduced to 1V maximum.

Q: What is the difference between MCR12DCMT4G and MCR12DSMT4G? A: MCR12DCMT4G is a standard recovery SCR with 20mA maximum gate trigger current. MCR12DSMT4G is a sensitive gate variant with 200µA maximum gate trigger current, requiring minimal gate drive power. MCR12DSMT4G has a reduced upper operating temperature limit of 110°C versus 125°C for MCR12DCMT4G.

Q: Is MCR8DCMT4G suitable as a substitute for S6010DRP? A: MCR8DCMT4G is suitable only if application current requirements do not exceed 8A RMS. The lower current rating reduces thermal headroom. All other electrical and package parameters are compatible.

Q: Why is S6006DRP listed as a parametric equivalent rather than a recommended substitute? A: S6006DRP provides only 6A on-state current, below the S6010DRP's 10A rating. It is included as a parametric equivalent for applications where lower current capacity is acceptable. REACH affected status also requires additional compliance verification.

Q: Are all substitute parts available in the same packaging format? A: Yes. All substitute parts use TO-252-3 DPAK (2 Leads + Tab) surface mount packaging, identical to the S6010DRP. PCB footprint and thermal pad dimensions are compatible across all listed substitutes.

Q: What compliance certifications apply to these substitutes? A: All substitute parts are ROHS3 compliant. MCR12DCMT4G and MCR8DCMT4G are REACH unaffected. MCR12DSMT4G and S6006DRP are REACH affected and require verification for regulated applications. All parts carry EAR99 export classification.