RMCF0201FT23K7 Equivalent & Substitute Parts

Part Overview

The RMCF0201FT23K7 is a 23.7 kOhms ±1% thick film chip resistor manufactured by Stackpole Electronics Inc, rated at 0.05W (1/20W) in the 0201 (0603 Metric) package. This component is actively produced and widely used in compact electronic assemblies where space constraints and precision resistance values are critical. Equivalent and substitute parts are identified based on matching electrical specifications, mechanical dimensions, and environmental ratings to ensure direct interchangeability in circuit designs.

Substiute Parts

RMCF0201FT23K7

Stackpole Electronics IncIn Stock: 897RMCF0201FT23K7 Datasheet

Current PartRFQ

CRCW020123K7FNED

Vishay DaleIn Stock: 10147CRCW020123K7FNED Datasheet

MFR RecommendedRFQ

ERJ-1GNF2372C

Panasonic Electronic ComponentsIn Stock: 71389ERJ-1GNF2372C Datasheet

MFR RecommendedRFQ

RC0201FR-0723K7L

YAGEOIn Stock: 84400RC0201FR-0723K7L Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitute parts for the RMCF0201FT23K7 are qualified based on the following criteria:

• Electrical Match: Resistance value of 23.7 kOhms with ±1% tolerance
• Power Rating: 0.05W (1/20W) minimum
• Package Compatibility: 0201 (0603 Metric) form factor with identical termination count (2)
• Environmental Specifications: Temperature coefficient of ±200ppm/°C and operating temperature range support
• Compliance: ROHS3 compliance and MSL 1 rating
• Physical Dimensions: Length 0.024" (0.60mm), Width 0.012" (0.30mm), with seated height ≤0.011" (0.28mm)

All identified substitutes meet these core parameters and are suitable for direct replacement in applications requiring the RMCF0201FT23K7.

Parameter Comparison

Engineering Selection Recommendations

All four parts listed are active products with ROHS3 compliance and MSL 1 ratings, confirming their suitability for modern electronics manufacturing and long-term storage without moisture sensitivity concerns.

CRCW020123K7FNED (Vishay Dale) maintains the full operating temperature range of -55°C to 155°C, matching the original RMCF0201FT23K7 specification. This part is recommended for applications requiring the extended upper temperature limit.

ERJ-1GNF2372C (Panasonic) and RC0201FR-0723K7L (YAGEO) both operate to 125°C maximum. The YAGEO part includes moisture-resistant thick film construction as an additional feature. These parts are suitable for standard industrial and consumer applications within the -55°C to 125°C range.

All substitutes are available in high inventory quantities, ensuring supply chain continuity and cost-effective procurement.

Frequently Asked Questions (FAQ)

Q: Can CRCW020123K7FNED replace RMCF0201FT23K7 in all applications? A: Yes. Both parts share identical electrical specifications (23.7 kOhms ±1%, 0.05W), composition (thick film), package (0201), and temperature coefficient (±200ppm/°C). CRCW020123K7FNED extends to 155°C, fully covering the original part's operating range.

Q: What is the difference between ERJ-1GNF2372C and RC0201FR-0723K7L? A: Both parts are electrically and mechanically equivalent with identical resistance, tolerance, power rating, and package specifications. RC0201FR-0723K7L includes moisture-resistant thick film construction. Both operate to 125°C maximum, which is 30°C lower than the original RMCF0201FT23K7.

Q: Are all substitute parts suitable for high-temperature applications above 125°C? A: No. ERJ-1GNF2372C and RC0201FR-0723K7L are rated to 125°C maximum. For applications requiring operation up to 155°C, use CRCW020123K7FNED or the original RMCF0201FT23K7.

Q: Do all parts meet the same compliance standards? A: Yes. All four parts are ROHS3 compliant, REACH unaffected, and carry MSL 1 (unlimited moisture sensitivity level) ratings, confirming equivalent environmental and regulatory compliance.

Q: Can these parts be used interchangeably on the same PCB assembly? A: Yes. All parts share the 0201 (0603 Metric) package with identical footprint dimensions (0.024" L × 0.012" W). Seated heights range from 0.010" to 0.011", which is within standard PCB assembly tolerances and does not affect interchangeability.