RG2012V-682-D-T5 Equivalent & Substitute Parts

Part Overview

The RG2012V-682-D-T5 is a 6.8 kOhms ±0.5% thin film chip resistor in 0805 (2012 Metric) package format, rated for 0.125W (1/8W) power dissipation. This component is manufactured by Susumu and features anti-sulfur coating with automotive AEC-Q200 qualification. The part maintains active product status with 1034 units currently in stock. Substitute parts are identified to address inventory availability, tolerance requirements, or specific application needs while maintaining electrical and mechanical compatibility.

Substiute Parts

RG2012V-682-D-T5

SusumuIn Stock: 1069RG2012V-682-D-T5 Datasheet

Current PartRFQ

RG2012V-682-P-T1

SusumuIn Stock: 2130RG2012V-682-P-T1 Datasheet

UpgradeRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution of the RG2012V-682-D-T5 is determined by the following critical parameters that must remain constant across all equivalent parts:

Mandatory Matching Parameters:

• Resistance value: 6.8 kOhms
• Package / Case: 0805 (2012 Metric)
• Power rating: 0.125W (1/8W)
• Composition: Thin Film
• Operating temperature range: -55°C ~ 155°C
• Temperature coefficient: ±5ppm/°C
• Physical dimensions: 0.079" L x 0.049" W (2.00mm x 1.25mm)
• Height - Seated (Max): 0.020" (0.50mm)
• Features: Anti-Sulfur, Automotive AEC-Q200
• RoHS Status: ROHS3 Compliant
• Moisture Sensitivity Level: 1 (Unlimited)

Allowable Variation:

• Tolerance: May be tighter (lower tolerance value) than the original specification

The substitute part RG2012V-682-P-T1 meets all mandatory parameters with an improved tolerance specification of ±0.02% compared to the original ±0.5%.

Parameter Comparison

Engineering Selection Recommendations

RG2012V-682-D-T5 (Original Part): Use this part when the ±0.5% tolerance specification is sufficient for the application requirements. The part is active, AEC-Q200 qualified, and maintains full automotive compliance with anti-sulfur coating. Current inventory of 1034 units supports standard procurement timelines.

RG2012V-682-P-T1 (Substitute Part): Use this part when tighter tolerance control is required. The ±0.02% tolerance provides superior accuracy compared to the original ±0.5% specification. Both parts share identical electrical ratings, package dimensions, temperature characteristics, and automotive qualifications. The substitute maintains full AEC-Q200 compliance and anti-sulfur protection. Higher inventory availability (2048 units) supports expedited procurement if needed.

Both parts are manufactured by Susumu, carry ROHS3 compliance, and are rated for identical operating conditions. Selection between these parts depends solely on tolerance requirements for the specific circuit application.

Frequently Asked Questions (FAQ)

Q: Can RG2012V-682-P-T1 be used as a direct replacement for RG2012V-682-D-T5?

A: Yes. Both parts are electrically and mechanically identical with respect to resistance value, power rating, package format, operating temperature range, and automotive qualifications. The substitute part features a tighter tolerance specification (±0.02% versus ±0.5%), which provides improved accuracy without affecting compatibility.

Q: What is the difference between these two part numbers?

A: The primary difference is tolerance specification. RG2012V-682-D-T5 carries ±0.5% tolerance, while RG2012V-682-P-T1 carries ±0.02% tolerance. All other electrical and mechanical parameters, including resistance value, power rating, package size, temperature coefficient, and automotive ratings, are identical.

Q: Are both parts suitable for automotive applications?

A: Yes. Both RG2012V-682-D-T5 and RG2012V-682-P-T1 are AEC-Q200 qualified with anti-sulfur coating, meeting automotive reliability standards. Both maintain identical operating temperature ranges of -55°C to 155°C.

Q: Do these parts have the same physical dimensions?

A: Yes. Both parts use the 0805 (2012 Metric) package with identical dimensions of 0.079" L x 0.049" W (2.00mm x 1.25mm) and maximum seated height of 0.020" (0.50mm). They are footprint-compatible for PCB assembly.

Q: What is the moisture sensitivity level for these parts?

A: Both parts carry Moisture Sensitivity Level (MSL) 1, which indicates unlimited shelf life without moisture control requirements.

Q: Are both parts RoHS compliant?

A: Yes. Both RG2012V-682-D-T5 and RG2012V-682-P-T1 are ROHS3 compliant.

Q: Which part should I select for precision applications?

A: RG2012V-682-P-T1 is the appropriate selection for applications requiring tighter tolerance control due to its ±0.02% tolerance specification compared to ±0.5% for the original part.