RG2012P-86R6-D-T5 Equivalent & Substitute Parts

Part Overview

The RG2012P-86R6-D-T5 is an 86.6 Ohm ±0.5% thin film chip resistor manufactured by Susumu in 0805 (2012 Metric) package format. This component is rated for 0.125W (1/8W) power dissipation and features anti-sulfur coating with automotive AEC-Q200 qualification. The part is active in production with 721 units currently in stock. Substitute parts are identified when equivalent electrical specifications and mechanical compatibility are required due to inventory constraints, design flexibility, or supply chain considerations.

Substiute Parts

RG2012P-86R6-D-T5

SusumuIn Stock: 798RG2012P-86R6-D-T5 Datasheet

Current PartRFQ

1-2176091-8

TE Connectivity Passive ProductIn Stock: 15991-2176091-8 Datasheet

DirectRFQ

ERA-6AEB86R6V

Panasonic Electronic ComponentsIn Stock: 6043ERA-6AEB86R6V Datasheet

UpgradeRFQ

RT0805BRD0786R6L

YAGEOIn Stock: 3541RT0805BRD0786R6L Datasheet

UpgradeRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility is determined by the following criteria:

Mandatory Matching Parameters:

• Resistance value: 86.6 Ohms (exact match required)
• Package / Case: 0805 (2012 Metric) (physical compatibility required)
• Composition: Thin Film (electrical characteristics consistency)
• Temperature Coefficient: ±25ppm/°C (stability requirement)
• Operating Temperature Range: -55°C ~ 155°C (environmental compatibility)
• Moisture Sensitivity Level: MSL 1 (Unlimited) (handling compatibility)
• RoHS Status: ROHS3 Compliant (regulatory requirement)

Acceptable Variation Parameters:

• Tolerance: Substitutes with ±0.1% tolerance are acceptable as they represent tighter specification than the ±0.5% requirement
• Power Rating: Substitutes with 0.25W (1/4W) rating are acceptable as they exceed the 0.125W minimum requirement
• Automotive AEC-Q200 certification: Present in main part and one substitute; absence in other substitutes does not disqualify them for non-automotive applications

All identified substitute parts meet the mandatory matching criteria and represent valid alternatives for circuit implementation.

Parameter Comparison

Engineering Selection Recommendations

Primary Selection (RG2012P-86R6-D-T5): Select the main part when automotive AEC-Q200 qualification is required and anti-sulfur coating is specified. This part maintains the original design specification with active production status and adequate inventory availability.

Substitute Selection - ERA-6AEB86R6V (Panasonic): This substitute is preferred when tighter tolerance (±0.1% versus ±0.5%) is beneficial and automotive AEC-Q200 qualification is required. The part maintains identical power rating, temperature coefficient, and operating range. Highest inventory availability (5994 units) supports supply chain flexibility. Seated height is 0.024" (0.60mm) compared to 0.020" (0.50mm) for the main part; verify PCB clearance in space-constrained applications.

Substitute Selection - RT0805BRD0786R6L (YAGEO): This substitute is acceptable when tighter tolerance (±0.1%) is acceptable and automotive AEC-Q200 qualification is not required. The part maintains identical power rating, temperature coefficient, and operating range. Seated height is 0.024" (0.60mm); verify PCB clearance in space-constrained applications. Inventory availability (3447 units) supports supply chain requirements.

Substitute Selection - 1-2176091-8 (TE Connectivity): This substitute is acceptable when higher power rating (0.25W versus 0.125W) provides design margin and tighter tolerance (±0.1%) is beneficial. Automotive AEC-Q200 qualification is not present. Seated height is 0.026" (0.65mm); verify PCB clearance in space-constrained applications. Inventory availability (1491 units) supports supply chain requirements.

All substitutes maintain active production status and ROHS3 compliance. Selection should be based on specific application requirements regarding automotive qualification, tolerance specification, and available PCB clearance.

Frequently Asked Questions (FAQ)

Q: Can ERA-6AEB86R6V be used as a direct replacement for RG2012P-86R6-D-T5?

A: Yes. Both parts share identical resistance value (86.6 Ohms), package format (0805), power rating (0.125W), temperature coefficient (±25ppm/°C), operating temperature range (-55°C ~ 155°C), and regulatory compliance (ROHS3). The ERA-6AEB86R6V features tighter tolerance (±0.1% versus ±0.5%) and maintains automotive AEC-Q200 qualification. Seated height difference (0.024" versus 0.020") requires PCB clearance verification.

Q: What is the difference between the ±0.5% tolerance of the main part and the ±0.1% tolerance of the substitutes?

A: Tolerance defines the acceptable resistance variation from the nominal 86.6 Ohm value. The main part allows variation between 86.17 and 87.03 Ohms. The substitute parts allow variation between 86.53 and 86.67 Ohms. Tighter tolerance (±0.1%) provides more precise resistance values and is suitable for applications requiring higher accuracy. Both tolerances are acceptable for general circuit applications; selection depends on circuit design requirements.

Q: Are all substitute parts suitable for automotive applications?

A: The ERA-6AEB86R6V and RG2012P-86R6-D-T5 both carry automotive AEC-Q200 qualification. The 1-2176091-8 (TE Connectivity) and RT0805BRD0786R6L (YAGEO) do not carry this certification. For automotive applications requiring AEC-Q200 compliance, select either the main part or the ERA-6AEB86R6V.

Q: What is the significance of the seated height difference between parts?

A: Seated height varies between 0.020" (0.50mm) for the main part and 0.026" (0.65mm) for the TE Connectivity substitute. This difference affects PCB clearance in space-constrained designs. Verify available clearance above the component location before selecting a substitute with greater seated height. The Panasonic and YAGEO substitutes have intermediate seated height of 0.024" (0.60mm).

Q: Can the 1-2176091-8 with 0.25W power rating replace the 0.125W main part?

A: Yes. The 0.25W (1/4W) power rating of the 1-2176091-8 exceeds the 0.125W requirement of the main part. Higher power rating provides additional thermal capability and is acceptable for direct substitution. All other electrical parameters (resistance, tolerance, temperature coefficient, operating range) are compatible. Verify PCB clearance due to increased seated height of 0.026" (0.65mm).

Q: What does MSL 1 (Unlimited) moisture sensitivity level mean?

A: MSL 1 (Unlimited) indicates the component has no moisture sensitivity restrictions. The part can be stored and handled without special moisture control measures. All parts in this comparison share MSL 1 classification, ensuring consistent handling requirements across all options.

Q: Are all parts ROHS3 compliant?

A: Yes. All parts listed (main and substitutes) are ROHS3 compliant, meeting regulatory requirements for hazardous substance restrictions. This compliance is consistent across all options and does not differentiate substitution eligibility.