RFNA4PCCE Equivalent & Substitute Parts

Part Overview

The RFNA4PCCE is an N Type Connector Plug with male pin configuration, manufactured by Bulgin for RF coaxial applications. This component features 50 Ohm impedance, panel mount capability with flange mounting, and compression contact termination. The connector is designed for frequencies up to 18 GHz and operates across a temperature range of -55°C to 155°C. The product maintains Active status and is ROHS3 compliant. Substitute parts are identified to provide alternative sourcing options when the primary part number is unavailable or when inventory requirements necessitate alternative stock sources.

Substiute Parts

RFNA4PCCE

BulginIn Stock: 1201RFNA4PCCE Datasheet

Current PartRFQ

RFNA4PGID

BulginIn Stock: 1256RFNA4PGID Datasheet

Parametric EquivalentRFQ

Key Parameters

Substitute Part Grouping Explanation

The RFNA4PCCE and its substitute RFNA4PGID are classified as parametric equivalents based on identical electrical and mechanical specifications. Substitution is valid when the following critical parameters match across both components:

Connector Style (N Type), Connector Type (Plug, Male Pin), Impedance (50 Ohms), Mounting Type (Panel Mount), Mounting Feature (Flange), Contact Termination (Compression), Shield Termination (Screw), Frequency Maximum (18 GHz), Operating Temperature Range (-55°C ~ 155°C), Voltage Rating (500 V), Mating Cycles (500), Center Contact Material (Beryllium Copper), Body Material (Stainless Steel), Dielectric Material (Polyetherimide), and RoHS Compliance Status (ROHS3 Compliant).

Both components share the same base product number (RFNA) and maintain identical performance characteristics across all specified parameters. The substitute part is suitable for direct replacement in applications where the primary part number is unavailable.

Parameter Comparison

Engineering Selection Recommendations

Both RFNA4PCCE and RFNA4PGID are Active status products manufactured by Bulgin with full ROHS3 compliance. Selection between these components is based on inventory availability and sourcing requirements rather than technical performance differentiation. The RFNA4PGID currently maintains higher inventory levels (1171 Pcs) compared to RFNA4PCCE (1093 Pcs), making it suitable for high-volume procurement scenarios. Both components satisfy identical electrical specifications, mechanical requirements, and regulatory compliance standards. Either component is suitable for direct substitution in RF coaxial connector applications requiring N Type male pin configuration with 50 Ohm impedance and panel mount flange installation.

Frequently Asked Questions (FAQ)

Q: Can RFNA4PGID be used as a direct replacement for RFNA4PCCE?

A: Yes. Both components are parametric equivalents with identical electrical and mechanical specifications. All critical parameters including connector style, impedance, mounting configuration, operating temperature range, voltage rating, and material composition are identical.

Q: Are there any performance differences between RFNA4PCCE and RFNA4PGID?

A: No performance differences exist between these components. Both maintain identical frequency response (18 GHz maximum), impedance (50 Ohms), operating temperature range (-55°C to 155°C), voltage rating (500 V), and mating cycle rating (500 cycles).

Q: What is the significance of the base product number RFNA?

A: The base product number RFNA identifies the core product family. Both RFNA4PCCE and RFNA4PGID share this base designation, indicating they belong to the same product line with consistent design and performance characteristics.

Q: Are both components RoHS compliant?

A: Yes. Both RFNA4PCCE and RFNA4PGID are ROHS3 compliant and suitable for applications requiring regulatory compliance with RoHS standards.

Q: What is the Moisture Sensitivity Level (MSL) rating?

A: Both components carry an MSL rating of 1 (Unlimited), indicating no moisture sensitivity restrictions during storage or handling.

Q: Can these connectors be used in high-frequency applications?

A: Yes. Both components support frequencies up to 18 GHz, making them suitable for RF and microwave applications within this frequency range.

Q: What mounting configuration do these connectors use?

A: Both components feature panel mount configuration with flange mounting and threaded fastening type, requiring four-hole installation on the mounting surface.

Q: What materials are used in the connector construction?

A: Both components use stainless steel for the body, beryllium copper for the center contact, and polyetherimide (PEI) as the dielectric material.