RF292A2PCEDK Equivalent & Substitute Parts

Part Overview

The RF292A2PCEDK is a 2.92mm coaxial connector plug with male pin configuration, designed for 50 Ohm impedance applications. This connector features panel mount through-hole solder termination with a flanged mounting interface and threaded fastening. The part is classified as Active product status and is ROHS3 compliant. Substitute parts are identified when equivalent electrical and mechanical parameters are required for applications where the original part number is unavailable or when alternative mounting configurations are necessary.

Substiute Parts

RF292A2PCEDK

BulginIn Stock: 733RF292A2PCEDK Datasheet

Current PartRFQ

RF292A2PEGDK

BulginIn Stock: 1171RF292A2PEGDK Datasheet

Parametric EquivalentRFQ

RF292A4PCCA

BulginIn Stock: 1050RF292A4PCCA Datasheet

Parametric EquivalentRFQ

RF292A4PCCDK

BulginIn Stock: 981RF292A4PCCDK Datasheet

Parametric EquivalentRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitute parts for the RF292A2PCEDK are identified based on strict equivalence of electrical and mechanical parameters. The primary substitution criteria are:

Electrical Parameters (Must Match):

• Connector Style: 2.92mm
• Connector Type: Plug, Male Pin
• Impedance: 50 Ohms
• Frequency - Max: 40 GHz
• Contact Termination: Solder
• Shield Termination: Solder

Mechanical Parameters (Must Match):

• Mounting Type: Panel Mount, Through Hole
• Mounting Feature: Flange
• Fastening Type: Threaded
• Number of Ports: 1

Environmental & Compliance Parameters (Must Match):

• Operating Temperature: -40°C ~ 85°C
• Voltage Rating: 250 V
• Mating Cycles: 500
• RoHS Status: ROHS3 Compliant
• Moisture Sensitivity Level: 1 (Unlimited)

Allowable Variation: The number of mounting holes may vary between substitute parts. The RF292A2PCEDK features 2-hole mounting, while substitute parts RF292A4PCCA and RF292A4PCCDK feature 4-hole mounting. This variation is permitted when the application PCB or panel design accommodates the alternative mounting hole configuration.

Parameter Comparison

Engineering Selection Recommendations

All substitute parts listed maintain full electrical and mechanical equivalence to the RF292A2PCEDK within the parameters specified. Selection between substitute parts is determined by mounting hole configuration requirements:

RF292A2PEGDK: Direct 2-hole mounting equivalent. All parameters identical to RF292A2PCEDK. Selection is appropriate when 2-hole panel mount configuration is required and RF292A2PCEDK is unavailable.

RF292A4PCCA and RF292A4PCCDK: 4-hole mounting variants. These parts are electrically and mechanically equivalent to RF292A2PCEDK with the exception of mounting hole count. Selection is appropriate when panel or PCB design accommodates 4-hole mounting configuration and enhanced mechanical stability is required.

All substitute parts are Active product status and ROHS3 compliant, meeting current regulatory requirements. Inventory availability is confirmed for all listed substitutes.

Frequently Asked Questions (FAQ)

Q: Can RF292A2PEGDK be used as a direct replacement for RF292A2PCEDK?

A: Yes. RF292A2PEGDK is a parametric equivalent with identical electrical and mechanical specifications. The only difference is internal construction details not affecting connector performance. Both parts feature 2-hole mounting configuration.

Q: What is the difference between 2-hole and 4-hole mounting variants?

A: The RF292A2PCEDK and RF292A2PEGDK feature 2-hole through-hole panel mount configuration. The RF292A4PCCA and RF292A4PCCDK feature 4-hole through-hole panel mount configuration. The 4-hole design provides additional mechanical support points on the panel. Selection depends on PCB or panel hole pattern availability.

Q: Are all substitute parts ROHS3 compliant?

A: Yes. All listed substitute parts are ROHS3 compliant and meet current regulatory requirements for electronic component manufacturing.

Q: Can I use a 4-hole variant if my panel only has 2 holes?

A: No. The mounting hole configuration must match the panel or PCB design. Use only parts with hole configurations compatible with your mechanical design.

Q: What is the maximum operating frequency for all substitute parts?

A: All substitute parts support 40 GHz maximum frequency operation, maintaining full RF performance equivalence across the product family.

Q: Are the electrical characteristics identical across all substitute parts?

A: Yes. All substitute parts maintain 50 Ohm impedance, identical contact materials (Beryllium Copper), identical dielectric material (Polyetherimide), and identical solder termination specifications.

Q: What is the operating temperature range for these connectors?

A: All parts operate within -40°C to 85°C temperature range with 250 V voltage rating and 500 mating cycle specification.