RC2012F3R9CS Equivalent & Substitute Parts

Part Overview

The RC2012F3R9CS is a 3.9 Ohm ±1% thick film chip resistor manufactured by Samsung Electro-Mechanics, rated for 0.125W (1/8W) power dissipation in a 0805 (2012 Metric) surface mount package. This component is classified as Active product status with full RoHS3 compliance and unlimited moisture sensitivity level (MSL 1). Equivalent and substitute parts are identified when design requirements necessitate alternative sourcing, inventory availability, or specific application certifications such as automotive AEC-Q200 qualification.

Substiute Parts

RC2012F3R9CS

Samsung Electro-MechanicsIn Stock: 1132RC2012F3R9CS Datasheet

Current PartRFQ

ERJ-6RQF3R9V

Panasonic Electronic ComponentsIn Stock: 20718ERJ-6RQF3R9V Datasheet

UpgradeRFQ

RC0805FR-073R9L

YAGEOIn Stock: 67928RC0805FR-073R9L Datasheet

UpgradeRFQ

RMCF0805FT3R90

Stackpole Electronics IncIn Stock: 21588RMCF0805FT3R90 Datasheet

UpgradeRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution of the RC2012F3R9CS is determined by strict equivalence across the following critical parameters:

Electrical Parameters:

• Resistance value: 3.9 Ohms (exact match required)
• Tolerance: ±1% (exact match required)
• Power rating: 0.125W / 1/8W (exact match required)

Mechanical Parameters:

• Package type: 0805 (2012 Metric) (exact match required)
• Termination count: 2 (exact match required)
• Composition: Thick Film (exact match required)

Environmental & Compliance Parameters:

• Operating temperature range: -55°C ~ 155°C (exact match required)
• RoHS3 compliance (required for all substitutes)
• Moisture Sensitivity Level: 1 (Unlimited) (exact match required)
• Packaging format: Tape & Reel (TR) (exact match required)

All identified substitute parts meet these criteria. Additional features such as automotive AEC-Q200 certification or enhanced temperature coefficient specifications represent functional enhancements that do not preclude substitution but may provide application-specific advantages.

Parameter Comparison

Engineering Selection Recommendations

All four parts listed are electrically and mechanically equivalent for direct substitution in applications requiring a 3.9 Ohm ±1% 0.125W 0805 thick film chip resistor. Selection among these alternatives is based on the following criteria:

RC2012F3R9CS (Samsung Electro-Mechanics): Primary specification. Suitable for general-purpose applications where automotive qualification is not required. Temperature coefficient of ±300ppm/°C is within acceptable range for standard industrial applications.

ERJ-6RQF3R9V (Panasonic Electronic Components): Qualified to AEC-Q200 automotive standard. Temperature coefficient of ±200ppm/°C provides improved stability. Recommended for automotive and high-reliability applications where AEC-Q200 certification is specified or preferred.

RC0805FR-073R9L (YAGEO): Moisture-resistant thick film composition. Temperature coefficient of ±200ppm/°C. Seated height of 0.024" (0.60mm) is the lowest among all options, suitable for space-constrained PCB layouts. Recommended for applications with tight vertical clearance requirements.

RMCF0805FT3R90 (Stackpole Electronics Inc): Qualified to AEC-Q200 automotive standard. Temperature coefficient of ±200ppm/°C. Seated height of 0.026" (0.65mm) matches the primary part specification. Recommended for automotive applications where AEC-Q200 certification is required and dimensional consistency with the original specification is prioritized.

All parts carry ROHS3 compliance, unlimited moisture sensitivity level (MSL 1), and active product status, ensuring long-term availability and regulatory compliance.

Frequently Asked Questions (FAQ)

Q: Can ERJ-6RQF3R9V or RMCF0805FT3R90 be used as direct replacements for RC2012F3R9CS in non-automotive applications?

A: Yes. Both parts meet all electrical and mechanical equivalence criteria. The AEC-Q200 automotive qualification is an additional feature that does not restrict use in non-automotive applications. These parts are fully compatible substitutes.

Q: What is the significance of the temperature coefficient difference (±300ppm/°C vs. ±200ppm/°C)?

A: Temperature coefficient indicates resistance value drift over temperature range. The RC2012F3R9CS exhibits ±300ppm/°C, while substitute parts ERJ-6RQF3R9V, RC0805FR-073R9L, and RMCF0805FT3R90 exhibit ±200ppm/°C. The lower coefficient in substitute parts represents improved temperature stability. For most applications, both values are acceptable within the -55°C ~ 155°C operating range.

Q: Are there height differences that affect PCB assembly?

A: Yes. Seated heights vary slightly: RC2012F3R9CS (0.026"), ERJ-6RQF3R9V (0.028"), RC0805FR-073R9L (0.024"), and RMCF0805FT3R90 (0.026"). The RC0805FR-073R9L is 0.002" shorter, which may be advantageous in space-constrained designs. The ERJ-6RQF3R9V is 0.002" taller. These differences are within typical PCB assembly tolerances but should be verified for applications with strict height constraints.

Q: Which substitute part should be selected for automotive applications?

A: Both ERJ-6RQF3R9V (Panasonic) and RMCF0805FT3R90 (Stackpole) carry AEC-Q200 automotive qualification. Selection between these two depends on secondary criteria such as inventory availability, lead time, or specific design preferences. Both are fully qualified for automotive use.

Q: Is the RC0805FR-073R9L suitable for current sense applications?

A: The RC0805FR-073R9L is not specifically designated for current sense applications. The ERJ-6RQF3R9V is explicitly listed with current sense capability. If current sense functionality is required, ERJ-6RQF3R9V is the appropriate selection.

Q: Are all substitute parts available in Tape & Reel (TR) packaging?

A: Yes. All identified substitute parts are supplied in Tape & Reel (TR) packaging format, matching the primary part specification for automated assembly compatibility.

Q: Can these parts be intermixed in the same production run?

A: All parts meet identical electrical specifications (3.9 Ohms ±1%, 0.125W, 0805 package) and are mechanically compatible. Intermixing is permissible from a functional standpoint. However, design documentation and bill of materials should specify the intended part number to maintain traceability and ensure consistent procurement.