RA2425-D06 Equivalent & Substitute Parts

Part Overview

The RA2425-D06 is a solid-state relay (SSR) manufactured by Carlo Gavazzi Inc., configured as a SPST-NO (1 Form A) device in a hockey puck package. This component is designed for AC load switching applications with zero-cross detection, operating with a 3–32VDC input and controlling loads from 24V to 280V at 25A maximum current. The part is currently active in production with 1090 units in stock.

Identifying equivalent and substitute parts is necessary when the primary part becomes unavailable, when supply chain optimization is required, or when design flexibility allows for alternative qualified components that meet identical electrical and mechanical specifications.

Substiute Parts

RA2425-D06

Carlo Gavazzi Inc.In Stock: 1102RA2425-D06 Datasheet

Current PartRFQ

84134010

Sensata-CrydomIn Stock: 115684134010 Datasheet

DirectRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the RA2425-D06 is determined by strict equivalence across the following critical parameters:

• Circuit Configuration: Must be SPST-NO (1 Form A)
• Output Type: Must be AC with zero-cross detection
• Input Voltage Range: Must support 3 ~ 32VDC
• Load Voltage Range: Must support 24 V ~ 280 V
• Load Current Rating: Must be rated for 25 A
• Package / Case: Must be hockey puck form factor
• Termination Style: Must use screw terminals
• Mounting Type: Must be chassis mount

The substitute part identified below meets all of these criteria and is therefore electrically and mechanically interchangeable with the RA2425-D06.

Parameter Comparison

Engineering Selection Recommendations

Both the RA2425-D06 and 84134010 are active production components with full regulatory compliance. The RA2425-D06 carries RoHS Compliant certification, while the 84134010 carries ROHS3 Compliant certification, indicating enhanced environmental compliance standards. Both parts are classified under the same HTSUS code and ECCN designation, confirming their functional and regulatory equivalence.

Selection between these two parts may be based on:

• Supply availability: Both manufacturers maintain active inventory; current stock levels are comparable (1090 units vs. 1057 units).
• Regulatory requirements: If ROHS3 compliance is mandated, the 84134010 is the appropriate choice. If RoHS Compliant status is sufficient, either part is acceptable.
• REACH compliance status: The RA2425-D06 is REACH Unaffected; the 84134010 is REACH Affected. Applications subject to REACH regulations should verify applicability before selection.
• Moisture sensitivity: The 84134010 carries MSL 1 (Unlimited) rating, indicating superior moisture tolerance compared to the RA2425-D06 (Not Applicable).

Frequently Asked Questions (FAQ)

Q: Can the 84134010 be used as a direct replacement for the RA2425-D06?

A: Yes. Both parts are electrically and mechanically equivalent. They share identical circuit configuration (SPST-NO), output type (AC, zero-cross), input voltage range (3–32VDC), load voltage range (24–280V), current rating (25A), package form factor (hockey puck), and termination style (screw terminal).

Q: Are there any compliance differences between these parts?

A: Both parts are RoHS compliant and carry the same ECCN and HTSUS classifications. The 84134010 carries ROHS3 Compliant certification versus RoHS Compliant for the RA2425-D06. The 84134010 is REACH Affected while the RA2425-D06 is REACH Unaffected. Applications with specific regulatory requirements should verify which certification level is required.

Q: What is the significance of the hockey puck package?

A: The hockey puck package is a standardized form factor for solid-state relays designed for chassis mounting with screw terminal connections. Both the RA2425-D06 and 84134010 use this identical package, ensuring mechanical interchangeability in existing designs without modification to mounting hardware or terminal connections.

Q: Are there any electrical performance differences?

A: No. Both parts operate within identical electrical specifications: 3–32VDC input, 24–280V load voltage, 25A maximum current, and AC zero-cross output type. They are functionally equivalent for all switching applications within these parameters.

Q: What should be considered when switching between these parts in production?

A: Verify that your application does not have specific REACH or moisture sensitivity requirements that would favor one part over the other. Both parts are in active production with comparable inventory levels. Confirm that your supply chain and procurement processes support either manufacturer before implementation.