PVG613PBF Equivalent & Substitute Parts

Part Overview

The PVG613PBF is a solid-state relay (SSR) manufactured by Infineon Technologies, configured as a SPST-NO (Single Pole Single Throw - Normally Open) switch with 1A load capacity and 0-60V output voltage range. This component is classified as obsolete, making equivalent and substitute parts necessary for ongoing design support and procurement.

The PVG613PBF operates with a 1.2VDC input trigger voltage and features a 500 mOhms maximum on-state resistance. It is packaged in a 6-DIP (0.300", 7.62mm) through-hole configuration with PC pin termination, suitable for printed circuit board assembly.

Substiute Parts

PVG613PBF

Infineon TechnologiesIn Stock: 928PVG613PBF Datasheet

Current PartRFQ

PVG612PBF

Infineon TechnologiesIn Stock: 3211PVG612PBF Datasheet

DirectRFQ

ASSR-1219-001E

Broadcom LimitedIn Stock: 5844ASSR-1219-001E Datasheet

MFR RecommendedRFQ

ASSR-1411-001E

Broadcom LimitedIn Stock: 1892ASSR-1411-001E Datasheet

MFR RecommendedRFQ

ASSR-1511-001E

Broadcom LimitedIn Stock: 3649ASSR-1511-001E Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the PVG613PBF is determined by the following critical parameters:

• Circuit configuration: SPST-NO (1 Form A)
• Package type: 6-DIP (0.300", 7.62mm)
• Mounting type: Through Hole
• Termination style: PC Pin
• Output voltage range: 0 V ~ 60 V
• Load current capability: Minimum 1 A
• On-state resistance: Maximum 500 mOhms
• Input voltage: 1.2VDC or compatible trigger level
• Output type: AC, DC capable

Substitute parts must maintain compatibility across all mechanical parameters (package, mounting, termination) and electrical parameters (voltage ratings, current capacity, on-state resistance). Parts with lower current ratings or higher on-state resistance do not qualify as direct substitutes for applications requiring the full 1A capacity.

Parameter Comparison

Engineering Selection Recommendations

Direct Equivalent (Active Status): PVG612PBF is the active-status equivalent from Infineon Technologies. It maintains identical electrical specifications (1A load current, 500 mOhms on-state resistance, 1.2VDC input) and mechanical compatibility (6-DIP package, through-hole mounting, PC pin termination). This part is recommended as the primary replacement for PVG613PBF in new designs and ongoing procurement.

Cross-Manufacturer Substitute (Full Specification Match): ASSR-1511-001E from Broadcom Limited provides full electrical and mechanical compatibility. It delivers 1A load current with 500 mOhms maximum on-state resistance, matching the PVG613PBF performance envelope. The input voltage is 1.3VDC (compared to 1.2VDC), which remains compatible with standard logic-level trigger circuits. This part is active and available in production quantities.

Partial Substitutes (Current Derating Required): ASSR-1219-001E and ASSR-1411-001E are not direct substitutes due to reduced load current ratings (200 mA and 600 mA respectively). These parts are suitable only for applications where the load current requirement is lower than 1A. ASSR-1219-001E exhibits significantly higher on-state resistance (10 Ohms), which may introduce unacceptable voltage drop in low-impedance load circuits.

All substitute parts maintain ROHS3 compliance, MSL 1 rating, and AC/DC output capability consistent with the original specification.

Frequently Asked Questions (FAQ)

Q: Can ASSR-1219-001E replace PVG613PBF in my application? A: ASSR-1219-001E is not a direct substitute. It is rated for 200 mA maximum load current, while PVG613PBF is rated for 1A. Use ASSR-1219-001E only if your application load current does not exceed 200 mA. Additionally, its 10 Ohms on-state resistance is significantly higher than the 500 mOhms specification of PVG613PBF, resulting in greater voltage drop across the relay.

Q: What is the difference between PVG612PBF and ASSR-1511-001E? A: Both are full electrical equivalents with 1A load current and 500 mOhms on-state resistance. PVG612PBF is manufactured by Infineon Technologies with 1.2VDC input specification. ASSR-1511-001E is manufactured by Broadcom Limited with 1.3VDC input specification. Both operate with standard logic-level trigger signals and are mechanically identical in 6-DIP package configuration.

Q: Are all substitute parts available in the same package? A: Yes. All listed substitute parts (PVG612PBF, ASSR-1219-001E, ASSR-1411-001E, ASSR-1511-001E) are packaged in 6-DIP (0.300", 7.62mm) through-hole configuration with PC pin termination, ensuring direct mechanical compatibility with PVG613PBF PCB layouts.

Q: Why is PVG613PBF marked as obsolete? A: PVG613PBF is classified as obsolete by Infineon Technologies. The active equivalent PVG612PBF should be used for new designs. Existing inventory of PVG613PBF may be available from component distributors, but long-term procurement should transition to active-status alternatives.

Q: Do all substitute parts meet the same compliance standards? A: Yes. All substitute parts listed are ROHS3 compliant, carry MSL 1 (Unlimited) moisture sensitivity rating, and are REACH unaffected, matching the compliance profile of PVG613PBF.