Equivalent & Substitute Parts for PVG613

Part Overview

The PVG613 is a solid-state relay (SSR) manufactured by Infineon Technologies, configured as a SPST-NO (Single Pole Single Throw - Normally Open) switch in a 6-DIP package. This component is rated for 1A load current at 0–60V with a maximum on-state resistance of 500 mOhms and requires 1.2VDC input. The PVG613 is classified as obsolete, making equivalent and substitute parts necessary for new designs and ongoing production support.

Key Parameters

Parameter	Value
Manufacturer Part Number	PVG613
Manufacturer	Infineon Technologies
Circuit Configuration	SPST-NO (1 Form A)
Package / Case	6-DIP (0.300", 7.62mm)
Mounting Type	Through Hole
Voltage - Input	1.2VDC
Voltage - Load	0 V ~ 60 V
Load Current	1 A
On-State Resistance (Max)	500 mOhms
Output Type	AC, DC
Product Status	Obsolete
RoHS Status	RoHS non-compliant

Substitute Part Grouping Explanation

Substitution for the PVG613 is determined by the following critical parameters:

Package compatibility: 6-DIP (0.300", 7.62mm) through-hole mounting
Circuit configuration: SPST-NO (1 Form A)
Load voltage range: 0–60V capability
Load current capacity: Minimum 1A
On-state resistance: Maximum 500 mOhms
Output type: AC and DC support
Input voltage: Compatibility with control signal levels

Substitute parts must meet or exceed these specifications. Parts with lower load current ratings, higher on-state resistance, or reduced voltage ranges are not direct equivalents but may serve in applications with reduced performance requirements.

Parameter Comparison

Part Number	Manufacturer	Load Current	Voltage - Load	On-State Resistance (Max)	Input Voltage	Output Type	Product Status	RoHS Status
PVG613	Infineon Technologies	1 A	0–60V	500 mOhms	1.2VDC	AC, DC	Obsolete	RoHS non-compliant
ASSR-1511-001E	Broadcom Limited	1 A	0–60V	500 mOhms	1.3VDC	AC, DC	Active	ROHS3 Compliant
ASSR-1411-001E	Broadcom Limited	600 mA	0–60V	1 Ohms	1.3VDC	AC, DC	Active	ROHS3 Compliant
AQV252	Panasonic Electric Works	400 mA	0–60V	1.4 Ohms	1.14VDC	AC, DC	Active	ROHS3 Compliant
AQV212	Panasonic Electric Works	550 mA	0–60V	2.5 Ohms	1.14VDC	AC, DC	Active	ROHS3 Compliant
AQV202	Panasonic Electric Works	400 mA	0–60V	1.4 Ohms	2.3VDC	AC, DC	Active	ROHS3 Compliant
AQV102	Panasonic Electric Works	600 mA	0–60V	700 mOhms	2.3VDC	DC	Active	ROHS3 Compliant
ASSR-1219-001E	Broadcom Limited	200 mA	0–60V	10 Ohms	1.3VDC	AC, DC	Active	ROHS3 Compliant
AQV201	Panasonic Electric Works	500 mA	0–40V	1 Ohms	2.3VDC	AC, DC	Active	ROHS3 Compliant
AQV251	Panasonic Electric Works	500 mA	0–40V	1 Ohms	1.14VDC	AC, DC	Active	ROHS3 Compliant
AQV101	Panasonic Electric Works	700 mA	0–40V	500 mOhms	2.3VDC	DC	Active	ROHS3 Compliant

Engineering Selection Recommendations

Direct Equivalent (Full Specification Match): ASSR-1511-001E is the only substitute that matches all electrical specifications of the PVG613: 1A load current, 0–60V load voltage range, 500 mOhms on-state resistance, and AC/DC output capability. This part is manufactured by Broadcom Limited and carries active product status with ROHS3 compliance, making it suitable for new designs requiring regulatory compliance.

Partial Equivalents (Reduced Load Current): ASSR-1411-001E, AQV212, and AQV102 support the full 0–60V load voltage range but with reduced load current capacity (600 mA or less). These are applicable only in applications where the actual load current does not exceed their rated capacity.

Voltage-Limited Substitutes (0–40V Maximum): AQV201 and AQV251 are restricted to 0–40V load voltage operation. These parts are not suitable for applications requiring the full 0–60V range of the PVG613.

Compliance Consideration: All substitute parts listed are ROHS3 compliant and carry active product status, addressing the obsolescence and regulatory limitations of the PVG613.

Frequently Asked Questions (FAQ)

Q: Can ASSR-1511-001E be used as a direct replacement for PVG613? A: Yes. ASSR-1511-001E meets all electrical and mechanical specifications: 1A load current, 0–60V load voltage, 500 mOhms on-state resistance, SPST-NO configuration, 6-DIP package, and AC/DC output support. Input voltage is 1.3VDC versus 1.2VDC for the PVG613, which is within typical control signal tolerances.

Q: What is the difference between parts rated for 0–60V and 0–40V load voltage? A: Parts rated for 0–40V cannot safely switch loads exceeding 40V. The PVG613 supports 0–60V, so substitutes must maintain this range unless the application is confirmed to operate below 40V.

Q: Why do some substitutes have higher on-state resistance? A: On-state resistance affects power dissipation and voltage drop across the relay. Higher resistance (e.g., 1.4 Ohms versus 500 mOhms) increases heat generation and may require thermal management in high-current applications. The PVG613 specification of 500 mOhms is a low-resistance design.

Q: Are AC/DC output types interchangeable with DC-only parts? A: No. DC-only parts (such as AQV101 and AQV102) cannot switch AC loads. The PVG613 supports both AC and DC; substitutes must match this capability for applications requiring AC switching.

Q: Does the 6-DIP package ensure mechanical compatibility? A: Yes. All listed substitutes use the same 6-DIP (0.300", 7.62mm) through-hole package with PC pin termination, ensuring direct PCB footprint compatibility. No layout modifications are required.

Q: What is the significance of input voltage differences (1.2V, 1.14V, 1.3V, 2.3V)? A: Input voltage specifies the control signal level required to activate the relay. Differences within 0.1–1.0V are typically accommodated by standard logic-level drivers. Higher input voltages (2.3V) may require different control circuitry but remain compatible with standard 3.3V or 5V logic outputs.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message