PV10-5SLF-L Equivalent & Substitute Parts

Part Overview

The PV10-5SLF-L is a yellow insulated spade terminal connector manufactured by Panduit Corp, designed for crimp termination of 10-12 AWG wire. This component features a 5 stud configuration with tin-plated copper contacts and serrated termination for secure wire attachment. The part is classified as obsolete, necessitating identification of active equivalent alternatives to maintain supply chain continuity for applications requiring this terminal type.

Substiute Parts

PV10-5SLF-L

Panduit CorpIn Stock: 849PV10-5SLF-L Datasheet

Current PartRFQ

PV10-6LF-L

Panduit CorpIn Stock: 1221PV10-6LF-L Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution of the PV10-5SLF-L is determined by the following critical parameters that must remain consistent:

Mandatory Matching Parameters:

• Wire Gauge: 10-12 AWG
• Terminal Type: Spring, Snap
• Insulation Type: Insulated Vinyl
• Color: Yellow
• Termination Method: Crimp
• Contact Material: Copper with Tin Finish
• Mounting Type: Free Hanging (In-Line)
• Series: Pan-Term®

Allowable Variation Parameters:

• Stud/Tab Size: The substitute part may differ in stud configuration
• Overall Dimensions: Width and length may vary proportionally with stud size change
• Tongue Inside Opening: May vary with stud size modification
• Product Status: Active status preferred for ongoing availability

The PV10-6LF-L qualifies as a substitute based on matching all mandatory parameters while providing an active product status alternative. The primary difference is the stud size increase from 5 to 6, which results in proportional dimensional changes.

Parameter Comparison

Engineering Selection Recommendations

The PV10-6LF-L serves as the active equivalent for the obsolete PV10-5SLF-L. Selection of this substitute is supported by the following factors:

Product Status Advantage: The PV10-6LF-L maintains active product status with Panduit Corp, ensuring continued availability and supply chain reliability compared to the obsolete main part.

Compliance Enhancement: The substitute part carries ROHS3 compliance certification, providing improved environmental and regulatory alignment for applications subject to RoHS requirements.

Functional Equivalence: Both parts maintain identical wire gauge (10-12 AWG), terminal type (Spring, Snap), insulation material (Vinyl), color (Yellow), and contact specifications (Copper with Tin finish).

Dimensional Consideration: The stud size increase from 5 to 6 results in proportional dimensional changes. The substitute part features a wider outer edge (0.300" versus 0.250") and greater overall length (1.030" versus 0.860"). These dimensional differences must be evaluated against specific mounting and spatial constraints in the application.

Regulatory Alignment: Both parts share identical ECCN (EAR99) and HTSUS classifications, maintaining consistent export and tariff treatment.

Frequently Asked Questions (FAQ)

Q: Can the PV10-6LF-L directly replace the PV10-5SLF-L in all applications?

A: The PV10-6LF-L matches all functional and electrical parameters of the PV10-5SLF-L. However, the larger stud size (6 versus 5) results in increased overall dimensions. Applications must accommodate the wider outer edge (0.300" versus 0.250") and greater length (1.030" versus 0.860"). Mounting clearances and stud hole sizing must be verified for compatibility.

Q: What is the significance of the stud size difference?

A: Stud size determines the mechanical interface between the terminal and the mating component. A 6 stud terminal requires a larger diameter hole than a 5 stud terminal. The substitute part is not interchangeable with the original part if the mating component has a 5 stud hole configuration.

Q: Are the wire gauge specifications identical?

A: Yes. Both the PV10-5SLF-L and PV10-6LF-L accommodate 10-12 AWG wire. The crimp termination process and wire contact specifications remain consistent between the two parts.

Q: What is the difference in insulation diameter?

A: Both parts maintain an insulation diameter of 0.225" (5.72mm). This parameter is consistent and does not vary between the main part and substitute.

Q: Does the RoHS3 compliance of the substitute part affect compatibility?

A: RoHS3 compliance of the PV10-6LF-L represents an environmental and regulatory advantage. This certification does not negatively impact electrical or mechanical compatibility with applications designed for the original part, provided the dimensional and stud size requirements are met.

Q: Are the contact materials and finishes the same?

A: Yes. Both parts feature copper contacts with tin plating. The serrated termination feature is present on both parts, ensuring equivalent wire retention and electrical contact characteristics.

Q: What packaging differences exist between these parts?

A: The PV10-5SLF-L is supplied in standard packaging, while the PV10-6LF-L is supplied in bulk packaging. Packaging format does not affect component functionality or performance.

Q: Can I use the PV10-6LF-L if my application specifies the PV10-5SLF-L?

A: Substitution requires verification that the mating component (stud hole configuration) accommodates the larger 6 stud size and that mounting space permits the increased dimensions. Electrical and functional compatibility is confirmed; mechanical compatibility must be independently verified.