PRA.M0.2GL.LC52A Equivalent & Substitute Parts

Part Overview

The PRA.M0.2GL.LC52A is a 2-position circular connector receptacle manufactured by LEMO, featuring female sockets with solder cup termination. This connector is designed for applications requiring push-pull detent lock fastening in automotive, industrial, medical, and testing equipment environments. The part is currently active in production with 1136 units in stock. Substitute parts are identified to provide alternative sourcing options when the primary part is unavailable or when design requirements permit equivalent connector specifications.

Substiute Parts

PRA.M0.2GL.LC52A

LEMOIn Stock: 1149PRA.M0.2GL.LC52A Datasheet

Current PartRFQ

K11MA7-P02LPH0-5260

ODUIn Stock: 971K11MA7-P02LPH0-5260 Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

The K11MA7-P02LPH0-5260 manufactured by ODU qualifies as a substitute for the PRA.M0.2GL.LC52A based on the following critical parameters:

• Connector Configuration: Both parts are 2-position circular connector receptacles with female sockets and solder cup termination
• Fastening Mechanism: Both employ push-pull detent lock fastening
• Shell Material: Both utilize Polysulfone (PSU) construction
• Contact Finish: Both feature gold-plated mating surfaces
• Ingress Protection: Both provide IP50 dust protection rating
• Cable Opening Compatibility: Both accept cables within the 0.157" ~ 0.205" (4.00mm ~ 5.20mm) range
• Regulatory Compliance: Both are ROHS3 compliant with MSL 1 rating and REACH unaffected status

Substitution is valid within applications where the operating temperature range and current rating differences are acceptable to the design requirements.

Parameter Comparison

Engineering Selection Recommendations

Both the PRA.M0.2GL.LC52A and K11MA7-P02LPH0-5260 are active production parts with equivalent regulatory compliance profiles. Selection between these parts should be based on the following considerations:

PRA.M0.2GL.LC52A (LEMO) is suitable when:

• Operating temperatures up to 150°C are required
• Current requirements are at or below 10A
• LEMO series compatibility is specified in design documentation

K11MA7-P02LPH0-5260 (ODU) is suitable when:

• Current requirements up to 14A are needed
• Operating temperatures do not exceed 120°C
• ODU MEDI-SNAP® series compatibility is acceptable
• Medical or military application certifications are required

Both parts maintain ROHS3 compliance, unlimited moisture sensitivity rating, and identical ingress protection and termination specifications, ensuring functional interchangeability within their respective thermal and current operating ranges.

Frequently Asked Questions (FAQ)

Q: Can K11MA7-P02LPH0-5260 replace PRA.M0.2GL.LC52A in all applications?

A: Substitution is valid when the application operating temperature does not exceed 120°C and current requirements do not exceed 14A. If the design requires operation above 120°C, the LEMO part must be used.

Q: What are the key differences between these connectors?

A: The primary differences are current rating (10A vs. 14A) and maximum operating temperature (150°C vs. 120°C). All other critical parameters including connector configuration, termination type, fastening mechanism, shell material, and contact finish are identical.

Q: Are both parts suitable for medical applications?

A: Both parts are ROHS3 compliant and carry MSL 1 rating. The ODU part is explicitly listed for medical applications. Confirm specific medical device requirements with application documentation.

Q: Do these connectors require any special handling during assembly?

A: Both connectors feature solder cup termination and identical cable opening specifications (0.157" ~ 0.205" / 4.00mm ~ 5.20mm). Standard solder cup assembly procedures apply to both parts.

Q: What is the inventory status for these parts?

A: PRA.M0.2GL.LC52A has 1136 units in stock. K11MA7-P02LPH0-5260 has 895 units in stock. Both are active production parts.