Equivalent & Substitute Parts for PH9130AL,115

Part Overview

The PH9130AL,115 is a MOSFET array manufactured by Nexperia USA Inc., classified as an obsolete product. As a legacy component no longer in active production, identification of suitable substitute parts is necessary for ongoing maintenance, repair, and redesign applications where the original part is unavailable or inventory is depleted.

Substiute Parts

PH9130AL,115

Nexperia USA Inc.In Stock: 88702PH9130AL,115 Datasheet

Current PartRFQ

PSMN9R1-30YL,115

Nexperia USA Inc.In Stock: 3906PSMN9R1-30YL,115 Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

The substitute part PSMN9R1-30YL,115 is identified as the manufacturer-recommended equivalent for the obsolete PH9130AL,115. Substitution is based on the following criteria:

Substitution Basis:

• Same manufacturer (Nexperia USA Inc.)
• Same component category (Transistors, FETs, MOSFETs)
• Functional equivalence as a MOSFET device
• Compliance with REACH regulations (REACH Unaffected status maintained)
• Availability of detailed electrical specifications enabling direct functional comparison

The PSMN9R1-30YL,115 is classified as "Not For New Designs," indicating it represents a transitional substitute rather than a long-term solution for new product development.

Parameter Comparison

Engineering Selection Recommendations

For Existing Equipment Maintenance: The PSMN9R1-30YL,115 is the manufacturer-designated substitute for the obsolete PH9130AL,115. Both components maintain REACH Unaffected status, ensuring regulatory compliance in existing applications.

For Redesign or New Applications: The PSMN9R1-30YL,115 carries a "Not For New Designs" status. While suitable for sustaining existing products, long-term product development should evaluate current-generation alternatives from Nexperia's active MOSFET portfolio to ensure extended availability and support.

Compliance Considerations: The substitute part is ROHS3 compliant and maintains REACH Unaffected status, supporting continued use in regulated markets without additional environmental or hazardous substance restrictions.

Frequently Asked Questions (FAQ)

Q: Can the PSMN9R1-30YL,115 directly replace the PH9130AL,115 in existing designs?

A: The PSMN9R1-30YL,115 is the manufacturer-recommended substitute. However, physical package differences must be verified. The PH9130AL,115 package specifications are not provided in available documentation. The substitute uses LFPAK56 (Power-SO8) surface mount packaging. PCB layout compatibility must be confirmed before implementation.

Q: What is the difference between "Obsolete" and "Not For New Designs" status?

A: "Obsolete" indicates the PH9130AL,115 is no longer manufactured and unavailable through normal distribution channels. "Not For New Designs" indicates the PSMN9R1-30YL,115 remains available for existing applications but should not be selected for new product development. For new designs, current-generation alternatives should be evaluated.

Q: Are there regulatory compliance differences between the two parts?

A: Both parts maintain REACH Unaffected status. The substitute (PSMN9R1-30YL,115) is additionally ROHS3 compliant, providing enhanced environmental compliance documentation for regulated applications.

Q: What electrical parameters should be verified for substitution compatibility?

A: The PH9130AL,115 detailed electrical specifications are not available in current documentation. Substitution decisions should be based on the application's requirements for drain-source voltage (Vdss), continuous drain current (Id), on-resistance (RDS(on)), and operating temperature range. The PSMN9R1-30YL,115 specifications are: 30V Vdss, 57A Id, 9.1 mOhm RDS(on), and -55°C to 175°C operating range.

Q: Is the surface mount LFPAK56 package compatible with the original PH9130AL,115 application?

A: Package compatibility depends on the original circuit board design. The PSMN9R1-30YL,115 uses surface mount technology (LFPAK56, Power-SO8). If the original design used a different package type or mounting method, physical redesign of the PCB may be required.