PDTA114EEAF Pre-Biased PNP Transistor Equivalent & Substitute Parts

Part Overview

The PDTA114EEAF is a pre-biased PNP bipolar junction transistor (BJT) manufactured by NXP USA Inc. in SC-75 (SOT-416) surface mount package. This device integrates internal base and emitter resistors for simplified circuit design in switching and amplification applications. The part is classified as obsolete, necessitating identification of active equivalent and substitute components that maintain electrical and mechanical compatibility for new designs and production continuity.

Key Parameters

Parameter	Value	Unit
Transistor Type	PNP - Pre-Biased	—
Maximum Collector Current (Ic)	100	mA
Collector-Emitter Breakdown Voltage (Max)	50	V
Base Resistor (R1)	10	kΩ
Emitter-Base Resistor (R2)	10	kΩ
DC Current Gain (hFE Min) @ Ic, Vce	30 @ 5mA, 5V	—
Vce Saturation (Max) @ Ib, Ic	150mV @ 500µA, 10mA	—
Transition Frequency	180	MHz
Maximum Power Dissipation	150	mW
Package / Case	SC-75, SOT-416	—
Mounting Type	Surface Mount	—
RoHS Status	ROHS3 Compliant	—
Moisture Sensitivity Level (MSL)	1 (Unlimited)	—

Substitute Part Grouping Explanation

Substitution of the PDTA114EEAF is determined by strict equivalence of the following electrical and mechanical parameters:

Critical Substitution Criteria:

Transistor type: PNP pre-biased configuration
Maximum collector current: 100 mA
Collector-emitter breakdown voltage: 50 V
Base resistor (R1): 10 kΩ
Emitter-base resistor (R2): 10 kΩ (primary criterion; 47 kΩ variants represent different bias characteristics)
Surface mount packaging compatible with SC-75 footprint or equivalent land pattern
RoHS3 compliance and MSL 1 rating

Substitute parts are grouped into two categories:

Category A - Direct Electrical Equivalents (R1=10kΩ, R2=10kΩ): Parts maintaining identical internal resistor values and electrical characteristics. These provide pin-for-pin or footprint-compatible replacement with no circuit modification required.

Category B - Functional Equivalents with Package Variants: Parts with identical electrical specifications but different surface mount packages (SOT-23, SOT-323, SOT-883, DFN). These require PCB layout adjustment but maintain full electrical compatibility.

Category C - Modified Bias Configuration: Parts with altered emitter-base resistor values (R2=47kΩ). These produce different bias characteristics and are suitable only when circuit design accommodates the modified bias point.

Parameter Comparison

Part Number	Manufacturer	Product Status	Ic (Max) mA	Vce Breakdown (Max) V	R1 (kΩ)	R2 (kΩ)	hFE Min @ 5mA, 5V	Vce Sat (Max) mV	Fт (MHz)	P (Max) mW	Package
PDTA114EEAF	NXP USA Inc.	Obsolete	100	50	10	10	30	150	180	150	SC-75
RN2102,LF(CT	Toshiba Semiconductor	Active	100	50	10	10	50 @ 10mA, 5V	300	200	100	SSM
DTA114EET1G	onsemi	Active	100	50	10	10	35 @ 5mA, 10V	250	—	200	SC-75
DTA114EETL	Rohm Semiconductor	Active	100	50	10	10	30 @ 5mA, 5V	300	250	150	EMT3
DTA114YET1G	onsemi	Active	100	50	10	47	80 @ 5mA, 10V	250	—	200	SC-75
PDTA114EM,315	Nexperia USA Inc.	Active	100	50	10	10	30 @ 5mA, 5V	150	—	250	SOT-883
PDTA114EMB,315	Nexperia USA Inc.	Active	100	50	10	10	30 @ 5mA, 5V	150	180	250	DFN1006B-3
PDTA114ET,235	NXP USA Inc.	Active	100	50	10	10	30 @ 5mA, 5V	150	—	250	SOT-23
PDTA114EU,135	Nexperia USA Inc.	Active	100	50	10	10	30 @ 5mA, 5V	150	180	200	SOT-323

Engineering Selection Recommendations

For Direct Replacement (Same Package SC-75/SOT-416):

DTA114EET1G (onsemi) is the primary active equivalent. This part maintains SC-75 packaging, identical internal resistor configuration (R1=10kΩ, R2=10kΩ), and active product status with full RoHS3 compliance. Inventory availability is 32,200 units. Electrical parameters are within acceptable tolerance for the PDTA114EEAF application envelope.

For Package-Flexible Designs:

PDTA114ET,235 (NXP USA Inc., SOT-23 package) provides the highest inventory availability (155,928 units) and maintains identical electrical specifications. This option is suitable when PCB layout permits SOT-23 footprint substitution. Active product status and NXP manufacturer continuity support long-term supply chain stability.

PDTA114EU,135 (Nexperia USA Inc., SOT-323 package) offers the smallest footprint option with 10,484 units in stock. This part is suitable for space-constrained applications and maintains full electrical equivalence.

For Automotive Applications:

PDTA114EM,315 and PDTA114EMB,315 (both Nexperia USA Inc.) carry AEC-Q100 qualification and automotive-grade designation. These parts are suitable for automotive and industrial applications requiring enhanced reliability certification. PDTA114EMB,315 provides DFN1006B-3 packaging with 16,055 units available.

For Modified Bias Requirements:

DTA114YET1G (onsemi) features R2=47kΩ emitter-base resistor, producing higher DC current gain (80 @ 5mA, 10V) compared to the standard 30. This variant is suitable only when circuit design specifically requires increased bias current or modified switching characteristics. Limited inventory (1,200 units) restricts this option to applications where bias modification is intentional.

For Alternative Manufacturer Sourcing:

RN2102,LF(CT (Toshiba Semiconductor, SSM package) provides active product status with 731 units in stock. This part maintains electrical equivalence with R1=10kΩ, R2=10kΩ configuration. Toshiba sourcing provides supply chain diversification independent of NXP/Nexperia/onsemi availability.

DTA114EETL (Rohm Semiconductor, EMT3 package) offers the highest transition frequency (250 MHz) and largest inventory (155,400 units). This part is suitable for high-frequency switching applications and provides strong supply continuity through Rohm's manufacturing capacity.

Frequently Asked Questions (FAQ)

Q: Can PDTA114EEAF be replaced with DTA114YET1G?

A: DTA114YET1G is electrically compatible for basic PNP pre-biased switching functions. However, the emitter-base resistor differs (47kΩ vs. 10kΩ), producing higher DC current gain (80 vs. 30). This modified bias point may alter circuit behavior. Substitution is valid only when the application circuit design accommodates or requires the increased bias current. Verify bias point requirements before implementation.

Q: What is the difference between SC-75 and SOT-323 packages?

A: SC-75 (SOT-416) and SOT-323 are both three-terminal surface mount packages but differ in physical dimensions and land pattern. SC-75 is larger and provides higher power dissipation capability (150-200 mW typical). SOT-323 is a miniature package suitable for space-constrained designs. Substitution requires PCB layout modification; the parts are not pin-for-pin compatible on the same board.

Q: Are all listed substitutes RoHS3 compliant?

A: All substitute parts listed carry RoHS3 compliance certification. PDTA114ET,235 does not explicitly state RoHS status in the provided data but is manufactured by NXP USA Inc. under current RoHS3 requirements. Verify RoHS documentation with the supplier for critical compliance applications.

Q: What is the significance of MSL 1 rating?

A: MSL (Moisture Sensitivity Level) 1 indicates unlimited shelf life without moisture bake-out requirements. All listed parts carry MSL 1 rating, meaning they can be stored and handled under standard warehouse conditions without special moisture control. This simplifies inventory management and reduces handling costs.

Q: Can PDTA114EEAF be replaced with RN2102,LF(CT from Toshiba?

A: Yes. RN2102,LF(CT maintains identical electrical specifications (Ic=100mA, Vce=50V, R1=10kΩ, R2=10kΩ). The SSM package differs from SC-75, requiring PCB layout modification. Toshiba sourcing provides supply chain independence. Verify package footprint compatibility before PCB design finalization.

Q: Which substitute offers the best long-term availability?

A: PDTA114ET,235 (NXP USA Inc., SOT-23 package) and DTA114EETL (Rohm Semiconductor, EMT3 package) offer the highest inventory levels (155,928 and 155,400 units respectively) and active product status. Both manufacturers maintain established production capacity. For critical applications requiring guaranteed long-term supply, either part provides superior availability assurance.

Q: Are automotive-qualified versions available?

A: Yes. PDTA114EM,315 and PDTA114EMB,315 (Nexperia USA Inc.) carry AEC-Q100 qualification and automotive-grade designation. These parts are suitable for automotive, industrial, and mission-critical applications requiring enhanced reliability certification. PDTA114EMB,315 provides DFN1006B-3 packaging with 16,055 units in stock.

Q: What is the difference between PDTA114EM,315 and PDTA114EMB,315?

A: Both parts are AEC-Q100 qualified automotive-grade components from Nexperia. PDTA114EM,315 uses SOT-883 package with 250 mW power rating. PDTA114EMB,315 uses DFN1006B-3 package with identical 250 mW power rating and 180 MHz transition frequency. Selection depends on PCB layout requirements and available board space.

Q: Can substitutes be mixed in production?

A: Substitution of different part numbers within a single production run is not recommended without formal design review and qualification testing. While all listed parts maintain electrical equivalence within specified parameters, package differences and manufacturer-specific process variations may introduce subtle performance differences. Maintain part number consistency within production batches unless engineering change order documentation explicitly authorizes substitution.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message