OPA2132UE4 Equivalent & Substitute Parts

Part Overview

The OPA2132UE4 is a J-FET input operational amplifier featuring dual circuits in an 8-SOIC surface mount package, manufactured by Texas Instruments. This device is classified as obsolete, necessitating identification of active equivalent and substitute components for new designs and production continuity. The OPA2132UE4 delivers a slew rate of 20V/µs with an 8 MHz gain bandwidth product, making it suitable for audio and precision signal conditioning applications requiring low input bias current (5 pA) and low input offset voltage (250 µV).

Key Parameters

Parameter	Value	Unit
Amplifier Type	J-FET	—
Number of Circuits	2	—
Slew Rate	20	V/µs
Gain Bandwidth Product	8	MHz
Current - Input Bias	5	pA
Voltage - Input Offset	250	µV
Current - Supply (per Channel)	4	mA
Current - Output / Channel	40	mA
Voltage - Supply Span (Min)	5	V
Voltage - Supply Span (Max)	36	V
Operating Temperature	-40 to 85	°C
Package / Case	8-SOIC (0.154", 3.90mm Width)	—
Mounting Type	Surface Mount	—
RoHS Status	ROHS3 Compliant	—
Moisture Sensitivity Level	3 (168 Hours)	—

Substitute Part Grouping Explanation

Substitution of the OPA2132UE4 is determined by strict alignment of electrical and mechanical parameters. The primary substitution criteria are:

Critical Parameters for Substitution:

Amplifier Type: J-FET input topology
Number of Circuits: Dual (2) configuration
Package / Case: 8-SOIC form factor
Slew Rate: 20V/µs minimum
Gain Bandwidth Product: 8 MHz minimum
Input Bias Current: 5 pA maximum
Input Offset Voltage: 250 µV maximum
Supply Voltage Range: Minimum 5V to maximum 36V overlap
Operating Temperature: -40°C to 85°C minimum coverage

Substitute parts are grouped into two categories based on electrical performance alignment:

Category 1 - Direct Functional Equivalents (Active Status): OPA2132U represents the active production variant of the same base product (OPA2132) with identical electrical specifications and 8-SOIC packaging. This part maintains full parameter compatibility with the obsolete OPA2132UE4.

Category 2 - Performance-Optimized Alternatives: AD8512BRZ, AD8512BRZ-REEL, and AD8512BRZ-REEL7 (Analog Devices) provide J-FET dual-circuit amplification in 8-SOIC packaging with enhanced specifications including lower input offset voltage (80 µV), reduced supply current (2.2 mA per channel), and extended operating temperature range (-40°C to 125°C). These parts maintain the 20V/µs slew rate and 8 MHz bandwidth.

Category 3 - Reduced Performance Alternatives: LT1057IS8, LT1057IS8#PBF, LT1057IS8#TRPBF, LT1057S8#PBF, and LT1057S8#TRPBF (Analog Devices) are J-FET dual-circuit amplifiers with reduced slew rate (13V/µs) and lower gain bandwidth product (5 MHz), suitable only for applications where these reduced specifications are acceptable.

LM833DT (STMicroelectronics) is an audio amplifier with different input bias current characteristics (300 nA) and reduced slew rate (7V/µs), applicable only to audio-specific applications.

Parameter Comparison

Part Number	Manufacturer	Amplifier Type	Circuits	Slew Rate (V/µs)	GBW (MHz)	Input Bias (pA)	Input Offset (µV)	Supply Current (mA)	Output Current (mA)	Supply Min (V)	Supply Max (V)	Temp Range (°C)	Package	Status
OPA2132UE4	Texas Instruments	J-FET	2	20	8	5	250	4	40	5	36	-40 to 85	8-SOIC	Obsolete
OPA2132U	Texas Instruments	J-FET	2	20	8	5	250	4	40	5	36	-40 to 85	8-SOIC	Active
AD8512BRZ	Analog Devices Inc.	J-FET	2	20	8	25	80	2.2	70	10	30	-40 to 125	8-SOIC	Active
AD8512BRZ-REEL	Analog Devices Inc.	J-FET	2	20	8	25	80	2.2	70	10	30	-40 to 125	8-SOIC	Active
AD8512BRZ-REEL7	Analog Devices Inc.	J-FET	2	20	8	25	80	2.2	70	10	30	-40 to 125	8-SOIC	Active
LM833DT	STMicroelectronics	Audio	2	7	15	300	300	4	37	5	30	-40 to 105	8-SOIC	Active
LT1057IS8	Analog Devices Inc.	J-FET	2	13	5	7	220	1.7	—	20	36	-40 to 85	8-SOIC	Active
LT1057IS8#PBF	Analog Devices Inc.	J-FET	2	13	5	7	220	1.7	—	20	36	-40 to 85	8-SOIC	Active
LT1057IS8#TRPBF	Analog Devices Inc.	J-FET	2	13	5	7	220	1.7	—	20	36	-40 to 85	8-SOIC	Active
LT1057S8#PBF	Analog Devices Inc.	J-FET	2	13	5	7	220	1.7	—	20	36	0 to 70	8-SOIC	Active
LT1057S8#TRPBF	Analog Devices Inc.	J-FET	2	13	5	7	220	1.7	—	20	36	0 to 70	8-SOIC	Active

Engineering Selection Recommendations

Primary Recommendation: OPA2132U

The OPA2132U is the direct active equivalent of the obsolete OPA2132UE4. Both parts share identical electrical specifications, J-FET input topology, dual-circuit configuration, and 8-SOIC packaging. The OPA2132U maintains active product status with ROHS3 compliance and is the preferred choice for direct replacement in existing designs. Packaging options include Tube format, providing compatibility with standard component handling and assembly processes.

Secondary Recommendation: AD8512BRZ Series

The AD8512BRZ, AD8512BRZ-REEL, and AD8512BRZ-REEL7 variants offer enhanced performance characteristics while maintaining the critical 20V/µs slew rate and 8 MHz gain bandwidth product. These parts feature improved input offset voltage (80 µV versus 250 µV), reduced supply current consumption (2.2 mA per channel versus 4 mA), and extended operating temperature range (-40°C to 125°C). All variants are ROHS3 compliant with MSL 1 rating. Selection among these three variants depends on packaging requirements: AD8512BRZ for tube packaging, AD8512BRZ-REEL for tape and reel, and AD8512BRZ-REEL7 for cut tape and Digi-Reel format. These parts are suitable for applications where improved specifications and extended temperature range provide system benefits.

Tertiary Recommendation: LT1057 Series

The LT1057IS8, LT1057IS8#PBF, LT1057IS8#TRPBF, LT1057S8#PBF, and LT1057S8#TRPBF are J-FET dual-circuit amplifiers with reduced slew rate (13V/µs) and lower gain bandwidth product (5 MHz). These parts are suitable only for applications where the reduced performance specifications are acceptable. The LT1057IS8 variants support -40°C to 85°C operating range, while LT1057S8 variants are limited to 0°C to 70°C. All variants require minimum 20V supply voltage, restricting use in 5V single-supply applications. Selection among variants depends on packaging and temperature requirements.

Not Recommended: LM833DT

The LM833DT is an audio amplifier with fundamentally different input characteristics (300 nA input bias current versus 5 pA) and reduced slew rate (7V/µs). This part is applicable only to audio-specific applications and does not provide functional equivalence for precision signal conditioning or general-purpose amplification requiring low input bias current.

Frequently Asked Questions (FAQ)

Q: Can OPA2132U directly replace OPA2132UE4 without circuit modifications?

A: Yes. The OPA2132U is the active production equivalent with identical electrical specifications, input/output characteristics, and 8-SOIC package dimensions. No circuit modifications are required. The only difference is product status (active versus obsolete) and packaging format options.

Q: What are the key differences between OPA2132U and AD8512BRZ?

A: Both parts maintain the critical 20V/µs slew rate and 8 MHz gain bandwidth product. The AD8512BRZ provides improved input offset voltage (80 µV versus 250 µV), lower supply current (2.2 mA per channel versus 4 mA), and extended operating temperature range (-40°C to 125°C versus -40°C to 85°C). The AD8512BRZ requires minimum 10V supply voltage, while OPA2132U operates from 5V minimum. Selection depends on whether improved specifications and extended temperature range are required for the application.

Q: Why is the LT1057 series not recommended as a direct replacement?

A: The LT1057 series has reduced slew rate (13V/µs versus 20V/µs) and lower gain bandwidth product (5 MHz versus 8 MHz). These reduced specifications may cause performance degradation in applications requiring the full 20V/µs slew rate or 8 MHz bandwidth. Additionally, LT1057 requires minimum 20V supply voltage, preventing use in 5V single-supply designs. Use LT1057 only when application requirements explicitly allow reduced performance specifications.

Q: What is the difference between AD8512BRZ, AD8512BRZ-REEL, and AD8512BRZ-REEL7?

A: All three variants have identical electrical specifications and performance. The differences are packaging format only: AD8512BRZ is supplied in Tube format, AD8512BRZ-REEL in Tape & Reel (TR) format, and AD8512BRZ-REEL7 in Cut Tape (CT) & Digi-Reel format. Select based on your assembly process requirements and component handling equipment.

Q: Is the LM833DT suitable for replacing OPA2132UE4 in audio applications?

A: The LM833DT is an audio amplifier with different input bias current (300 nA versus 5 pA) and reduced slew rate (7V/µs versus 20V/µs). While it is optimized for audio applications, it does not provide functional equivalence for the OPA2132UE4. Use LM833DT only if your audio application explicitly requires audio-optimized characteristics and can tolerate the reduced slew rate and higher input bias current.

Q: What is the significance of the MSL (Moisture Sensitivity Level) rating difference?

A: OPA2132UE4 has MSL 3 (168 hours), requiring controlled storage and handling. AD8512BRZ series and LT1057 series have MSL 1 (unlimited), allowing standard storage without moisture control requirements. MSL 1 rated parts provide simplified supply chain and manufacturing logistics.

Q: Can I use LT1057S8#PBF in applications requiring -40°C to 85°C operation?

A: No. LT1057S8#PBF is rated for 0°C to 70°C operating temperature only. For -40°C to 85°C operation, use LT1057IS8, LT1057IS8#PBF, or LT1057IS8#TRPBF, which support the full -40°C to 85°C range.

Q: Are all substitute parts ROHS3 compliant?

A: Yes. OPA2132U, AD8512BRZ series, LM833DT, and all LT1057 variants are ROHS3 compliant, meeting environmental and regulatory requirements for new designs.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message