MV6152 Equivalent & Substitute Parts

Part Overview

The MV6152 is an orange LED indication component manufactured by onsemi, featuring a 5mm T-1 3/4 through-hole radial package with clear lens and domed top. This part operates at 2V forward voltage with 100mcd brightness rating and 28° viewing angle. The MV6152 is classified as obsolete, making equivalent substitute parts necessary for ongoing design requirements and production continuity. Substitute parts must maintain compatibility with the through-hole radial mounting configuration and similar electrical operating parameters.

Substiute Parts

MV6152

onsemiIn Stock: 1167MV6152 Datasheet

Current PartRFQ

4302H1-12V

Visual Communications Company - VCCIn Stock: 20274302H1-12V Datasheet

SimilarRFQ

4302H1-5V

Visual Communications Company - VCCIn Stock: 27094302H1-5V Datasheet

SimilarRFQ

HLMP-D155

Broadcom LimitedIn Stock: 9365HLMP-D155 Datasheet

SimilarRFQ

LTL-307EE-012

Lite-On Inc.In Stock: 1097LTL-307EE-012 Datasheet

SimilarRFQ

LTL-4214

Lite-On Inc.In Stock: 803LTL-4214 Datasheet

SimilarRFQ

SLR-56VC3F

Rohm SemiconductorIn Stock: 3145SLR-56VC3F Datasheet

SimilarRFQ

SLR-56VCT32

Rohm SemiconductorIn Stock: 1029SLR-56VCT32 Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the MV6152 is determined by the following critical parameters:

• Lens Size & Mounting: All substitutes must use 5mm T-1 3/4 through-hole radial package configuration
• Voltage - Forward (Vf): Operating voltage must be 2V or within compatible range for direct circuit substitution
• Current - Test: Test current of 20mA or compatible lower current ratings
• Package / Case: Radial configuration required for PCB compatibility
• Wavelength - Peak: Red spectrum (623nm–660nm) or orange spectrum (635nm) acceptable for indication applications

The substitute parts listed below meet these mechanical and electrical compatibility criteria. Color variation from orange to red is acceptable within the red-orange spectrum range (623nm–660nm peak wavelength) for standard indication applications.

Parameter Comparison

Engineering Selection Recommendations

Primary Substitutes (Closest Electrical Match)

LTL-307EE-012 and SLR-56VCT32 / SLR-56VC3F are the closest electrical equivalents to MV6152. Both operate at 2V forward voltage with 20mA and 10mA test current respectively, matching the original part's voltage specification. LTL-307EE-012 maintains 90mcd brightness (comparable to MV6152's 100mcd) and identical 2V / 20mA operating parameters. SLR-56VCT32 and SLR-56VC3F are functionally identical variants differing only in packaging (Tape & Box vs. Bulk). All three primary substitutes are ROHS3 compliant and carry active product status.

Secondary Substitutes (Voltage Deviation)

LTL-4214 operates at 2.1V forward voltage with reduced current (10mA) and lower brightness (19mcd). HLMP-D155 operates at 1.7V forward voltage with minimal test current (1mA) and significantly reduced brightness (10mcd). These parts are suitable only where circuit design accommodates voltage variation and reduced brightness is acceptable.

Not Recommended for Direct Substitution

4302H1-5V operates at 5V forward voltage, requiring circuit redesign and is not suitable for direct pin-compatible replacement in 2V circuits.

All recommended substitutes maintain through-hole radial package compatibility, 5mm T-1 3/4 lens size, and mechanical fit within the original 8.89mm height specification (with minor tolerance variations). Product status verification confirms all primary substitutes are active and available.

Frequently Asked Questions (FAQ)

Q: Can MV6152 be directly replaced with 4302H1-5V?

A: No. The 4302H1-5V operates at 5V forward voltage compared to MV6152's 2V specification. Direct substitution requires circuit redesign and is not pin-compatible without voltage adjustment.

Q: What is the brightness difference between MV6152 and LTL-307EE-012?

A: MV6152 is rated at 100mcd while LTL-307EE-012 is rated at 90mcd. Both operate at identical 2V / 20mA parameters. The 10mcd difference is within acceptable tolerance for standard indication applications.

Q: Are SLR-56VCT32 and SLR-56VC3F electrically identical?

A: Yes. Both parts are electrically identical, operating at 2V forward voltage with 10mA test current and 25mcd brightness. The difference is packaging only: SLR-56VCT32 is supplied in Tape & Box format while SLR-56VC3F is supplied in Bulk packaging.

Q: Does the viewing angle difference affect substitution?

A: Viewing angle varies among substitutes (16° to 60°). MV6152 specifies 28°. Substitutes with wider viewing angles (40°–60°) provide broader light distribution, while narrower angles (16°–24°) provide more focused indication. Selection depends on application requirements.

Q: Are all substitute parts RoHS compliant?

A: All listed active substitutes are ROHS3 compliant. MV6152 status is not specified but is obsolete. RoHS compliance is confirmed for LTL-307EE-012, SLR-56VCT32, SLR-56VC3F, LTL-4214, HLMP-D155, and 4302H1-5V.

Q: What is the maximum height tolerance for PCB clearance?

A: MV6152 maximum height is 8.89mm. Substitutes range from 8.60mm (LTL-4214) to 12.44mm (HLMP-D155). Verify PCB clearance requirements before selecting substitutes with heights exceeding 9mm.

Q: Can HLMP-D155 be used as a direct replacement?

A: HLMP-D155 operates at 1.7V forward voltage with 1mA test current and 10mcd brightness—significantly different from MV6152's 2V / 20mA / 100mcd specification. Substitution requires circuit redesign and is suitable only where reduced brightness and lower current draw are acceptable.