MV60539MP6 Equivalent & Substitute Parts

Part Overview

The MV60539MP6 is a Circuit Board Indicator LED manufactured by onsemi, featuring a single red diffused lens in a 5mm T-1 3/4 through-hole right-angle configuration. This component is classified as obsolete, making identification of equivalent and substitute parts essential for design continuity and procurement planning. The part operates at 1.7V with a 20mA rated current and delivers 3.2mcd brightness with a 65° viewing angle.

Substiute Parts

MV60539MP6

onsemiIn Stock: 980MV60539MP6 Datasheet

Current PartRFQ

MV60539MP6

onsemiIn Stock: 980MV60539MP6 Datasheet

DirectRFQ

MV60539MP7

onsemiIn Stock: 962MV60539MP7 Datasheet

DirectRFQ

5HDL

Bivar Inc.In Stock: 10105HDL Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution for the MV60539MP6 is determined by alignment across the following critical parameters:

Direct Equivalents maintain identical or functionally equivalent specifications across all electrical and mechanical characteristics: color (red), configuration (single), lens type (diffused), lens style (round with domed top), lens size (5mm T-1 3/4), and mounting type (through hole, right angle). Voltage rating, current rating, and brightness output must remain within acceptable operational ranges for the target application.

Similar Alternatives share the same physical form factor (5mm T-1 3/4 through-hole red diffused LED) but may differ in electrical parameters such as forward voltage, test current, or brightness output. These parts are suitable for applications where the specific electrical characteristics of the original part are not critical constraints.

The following parameters establish substitution validity:

• Lens size and style (5mm T-1 3/4, round with domed top)
• Color (red)
• Lens type (diffused)
• Mounting configuration (through hole)
• Physical orientation compatibility

Parameter Comparison

Engineering Selection Recommendations

MV60539MP7 (onsemi) is the direct equivalent substitute for MV60539MP6. Both parts share identical electrical specifications (1.7V, 20mA, 3.2mcd), mechanical configuration (5mm T-1 3/4 right-angle through-hole), and regulatory compliance (REACH Unaffected, MSL 1). Both components are classified as obsolete; however, MV60539MP7 maintains the same base product number (MV605) and functional characteristics. This part is suitable for direct replacement in existing designs without circuit modification.

5HDL (Bivar Inc.) is an active product alternative that shares the same physical form factor and red diffused lens configuration. This part differs in electrical parameters: forward voltage is 2V (versus 1.7V), test current is 2mA (versus 20mA), and brightness output is 5mcd (versus 3.2mcd). The viewing angle is narrower at 45° compared to 65°. The 5HDL is suitable for applications where the original part's specific electrical characteristics are not design-critical constraints. Circuit design review is required to confirm compatibility with existing current-limiting resistor values and brightness requirements.

Both substitute parts maintain ROHS3 compliance and unlimited moisture sensitivity rating, ensuring compatibility with standard PCB assembly and storage conditions.

Frequently Asked Questions (FAQ)

Q: Can MV60539MP7 be used as a direct replacement for MV60539MP6?

A: Yes. MV60539MP7 is a direct equivalent with identical electrical ratings (1.7V, 20mA, 3.2mcd), mechanical configuration (5mm T-1 3/4 right-angle through-hole), and regulatory compliance. No circuit modifications are required.

Q: What are the key differences between MV60539MP6 and 5HDL?

A: The 5HDL differs in three electrical parameters: forward voltage (2V vs. 1.7V), test current (2mA vs. 20mA), and brightness output (5mcd vs. 3.2mcd). The viewing angle is also narrower (45° vs. 65°). Physical form factor and lens type remain compatible. Circuit design review is necessary to confirm suitability.

Q: Why is the 5HDL listed as a similar alternative rather than a direct equivalent?

A: The 5HDL operates at different electrical parameters and has a narrower viewing angle. While it shares the same 5mm T-1 3/4 through-hole red diffused lens configuration, the electrical differences require circuit validation before substitution.

Q: Are all three parts suitable for the same PCB layout?

A: MV60539MP6 and MV60539MP7 are mechanically and electrically identical and require no layout changes. The 5HDL shares the same 5mm T-1 3/4 through-hole right-angle mounting configuration and will fit the same PCB footprint. However, the different forward voltage and current characteristics may require resistor value adjustment in the current-limiting circuit.

Q: What is the regulatory compliance status of these parts?

A: MV60539MP6 and MV60539MP7 are both REACH Unaffected with MSL 1 (Unlimited). The 5HDL is ROHS3 Compliant with MSL 1 (Unlimited). All three parts meet standard regulatory requirements for circuit board indicator applications.

Q: Why are MV60539MP6 and MV60539MP7 both classified as obsolete?

A: Both parts are end-of-life products from onsemi. The 5HDL, manufactured by Bivar Inc., is an active product and represents a viable long-term alternative for new designs or ongoing production requirements.