Request Quote
(Ships tomorrow)
MMZ2012R600AT000 Equivalent & Substitute Parts
Part Overview
The MMZ2012R600AT000 is a 60 Ohm ferrite bead manufactured by TDK Corporation in 0805 (2012 Metric) surface mount package. This single-line signal ferrite bead operates at 100 MHz with 1A maximum current rating and 100mOhm DC resistance. The part is classified as Last Time Buy, indicating limited availability. Equivalent and substitute parts are necessary to ensure design continuity, accommodate supply constraints, and optimize performance characteristics for specific application requirements.
Substiute Parts
Key Parameters
| Parameter | Value |
|---|---|
| Manufacturer Part Number | MMZ2012R600AT000 |
| Manufacturer | TDK Corporation |
| Impedance @ Frequency | 60 Ohms @ 100 MHz |
| Current Rating (Max) | 1A |
| DC Resistance (DCR) (Max) | 100mOhm |
| Package / Case | 0805 (2012 Metric) |
| Operating Temperature | -55°C ~ 125°C |
| Filter Type | Signal Line |
| Number of Lines | 1 |
| RoHS Status | ROHS3 Compliant |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
Substitute Part Grouping Explanation
Substitution of the MMZ2012R600AT000 is determined by the following critical parameters:
Primary Matching Criteria:
- Impedance @ 100 MHz: 60 Ohms (exact match required for signal integrity)
- Package / Case: 0805 (2012 Metric) (physical and electrical compatibility)
- Number of Lines: 1 (single signal line application)
- Current Rating: Equal to or greater than 1A
- DC Resistance: Equal to or less than 100mOhm (lower DCR preferred for reduced insertion loss)
- Operating Temperature Range: Must encompass -55°C ~ 125°C or be compatible with application limits
- RoHS3 Compliance: Required for regulatory alignment
Substitute Categories:
Category 1: Direct Parametric Equivalents (0805 Package, 60 Ohm Impedance) Parts matching all primary criteria with identical package and impedance specifications.
Category 2: Manufacturer Alternatives (0805 Package, 60 Ohm Impedance) Alternative manufacturers offering equivalent electrical performance in the same package.
Category 3: Parametric Variants (0805 Package, Impedance Tolerance) Parts with similar impedance values (50-70 Ohm range) suitable for applications with impedance tolerance flexibility.
Category 4: Package Downsizes (0603 Package, 60 Ohm Impedance) Smaller package alternatives with identical impedance for space-constrained designs, with reduced current rating consideration.
Parameter Comparison
| Manufacturer Part Number | Manufacturer | Impedance @ 100 MHz | Current Rating (Max) | DC Resistance (Max) | Package / Case | Operating Temperature | Product Status | RoHS Status |
|---|---|---|---|---|---|---|---|---|
| MMZ2012R600AT000 | TDK Corporation | 60 Ohms | 1A | 100mOhm | 0805 (2012 Metric) | -55°C ~ 125°C | Last Time Buy | ROHS3 Compliant |
| MMZ2012Y600BT000 | TDK Corporation | 60 Ohms | 1A | 100mOhm | 0805 (2012 Metric) | -55°C ~ 125°C | Last Time Buy | ROHS3 Compliant |
| MMZ1608R600ATA00 | TDK Corporation | 60 Ohms | 800mA | 100mOhm | 0603 (1608 Metric) | -55°C ~ 125°C | Active | ROHS3 Compliant |
| MFBW1V2012-600-R | Eaton - Electronics Division | 60 Ohms | 3A | 60mOhm | 0805 (2012 Metric) | -40°C ~ 85°C | Active | ROHS3 Compliant |
| MH2029-600Y | Bourns Inc. | 60 Ohms | 5A | 20mOhm | 0805 (2012 Metric) | -55°C ~ 125°C | Active | ROHS3 Compliant |
| MU2029-600Y | Bourns Inc. | 60 Ohms | 900mA | 100mOhm | 0805 (2012 Metric) | -55°C ~ 125°C | Active | ROHS3 Compliant |
| ACML-0805-600-T | Abracon LLC | 60 Ohms | 1A | 50mOhm | 0805 (2012 Metric) | -55°C ~ 125°C | Active | ROHS3 Compliant |
| ACML-0805-500-T | Abracon LLC | 50 Ohms | 1A | 50mOhm | 0805 (2012 Metric) | -55°C ~ 125°C | Active | ROHS3 Compliant |
| ACML-0805-700-T | Abracon LLC | 70 Ohms | 1A | 80mOhm | 0805 (2012 Metric) | -55°C ~ 125°C | Active | ROHS3 Compliant |
Engineering Selection Recommendations
Tier 1: Direct Replacement (Identical Specifications)
MMZ2012Y600BT000 (TDK Corporation) is the primary direct replacement. Both parts share identical electrical specifications (60 Ohms @ 100 MHz, 1A, 100mOhm DCR) and package form factor. Both are Last Time Buy status, indicating similar supply constraints. Selection between MMZ2012R600AT000 and MMZ2012Y600BT000 depends on internal TDK variant differences not specified in provided parameters.
Tier 2: Active Status Alternatives (0805 Package, 60 Ohm Impedance)
ACML-0805-600-T (Abracon LLC) provides an active product alternative with identical impedance and current rating. DC resistance is reduced to 50mOhm, offering lower insertion loss. Active product status ensures continued availability.
MU2029-600Y (Bourns Inc.) maintains 60 Ohm impedance with 900mA current rating (slightly below 1A specification) and 100mOhm DCR. Active status and full temperature range (-55°C ~ 125°C) support long-term supply continuity.
Tier 3: Enhanced Performance Alternatives (0805 Package, 60 Ohm Impedance)
MH2029-600Y (Bourns Inc.) offers superior current handling (5A) and significantly reduced DC resistance (20mOhm). Operating temperature range (-40°C ~ 85°C) is narrower than the original part. This option is suitable for applications requiring lower insertion loss and higher current capacity within the specified temperature limits.
MFBW1V2012-600-R (Eaton - Electronics Division) provides 3A current rating and 60mOhm DCR. Operating temperature range (-40°C ~ 85°C) is narrower. Selection requires verification that application temperature requirements fall within this range.
Tier 4: Package Downsize Alternative (0603 Package, 60 Ohm Impedance)
MMZ1608R600ATA00 (TDK Corporation) is a 0603 (1608 Metric) package variant with identical impedance and DCR. Current rating is reduced to 800mA. This option applies only to space-constrained designs where the reduced current capacity is acceptable and PCB layout permits package downsizing.
Tier 5: Impedance Tolerance Variants (0805 Package, ±10 Ohm Range)
ACML-0805-500-T (50 Ohms @ 100 MHz) and ACML-0805-700-T (70 Ohms @ 100 MHz) are suitable only for applications with impedance tolerance specifications that permit ±10 Ohm deviation from 60 Ohms. Both maintain 1A current rating and active product status.
Compliance and Certification:
All listed substitutes are ROHS3 compliant and carry MSL 1 (Unlimited) moisture sensitivity rating, matching the original part's environmental qualifications.
Frequently Asked Questions (FAQ)
Q: Can MMZ2012Y600BT000 be used as a direct replacement for MMZ2012R600AT000?
A: Yes. Both parts are TDK Corporation ferrite beads with identical electrical specifications (60 Ohms @ 100 MHz, 1A, 100mOhm DCR) and 0805 package form factor. The primary difference is internal variant designation. Both are Last Time Buy status.
Q: What is the impact of using ACML-0805-600-T instead of MMZ2012R600AT000?
A: ACML-0805-600-T maintains identical impedance (60 Ohms @ 100 MHz) and current rating (1A) but reduces DC resistance from 100mOhm to 50mOhm. This results in lower insertion loss. The part is manufactured by Abracon LLC and carries Active product status, ensuring continued availability. All other electrical and environmental specifications remain compatible.
Q: Why is MMZ1608R600ATA00 listed as a substitute if it has a different package?
A: MMZ1608R600ATA00 is a 0603 (1608 Metric) package alternative for space-constrained applications. It maintains 60 Ohm impedance and 100mOhm DCR but reduces current rating to 800mA. Package downsizing is only applicable when PCB layout permits and application current requirements do not exceed 800mA.
Q: Can MH2029-600Y be used in all applications where MMZ2012R600AT000 is specified?
A: MH2029-600Y is suitable for applications within the operating temperature range of -40°C ~ 85°C. If the design requires operation below -40°C or above 85°C, this part is not compatible. Within the specified temperature range, MH2029-600Y offers superior performance with 5A current rating and 20mOhm DCR.
Q: What is the difference between ACML-0805-500-T, ACML-0805-600-T, and ACML-0805-700-T?
A: These three Abracon LLC parts differ in impedance specification: 50 Ohms, 60 Ohms, and 70 Ohms respectively, all measured at 100 MHz. ACML-0805-600-T matches the original 60 Ohm specification exactly. The 50 Ohm and 70 Ohm variants are suitable only for applications with documented impedance tolerance that permits ±10 Ohm deviation.
Q: Are all substitute parts RoHS3 compliant?
A: Yes. All listed substitute parts carry ROHS3 compliance certification, matching the environmental qualification of MMZ2012R600AT000.
Q: Which substitute offers the best long-term availability?
A: Parts with Active product status offer the best long-term availability: ACML-0805-600-T (Abracon LLC), MH2029-600Y (Bourns Inc.), MU2029-600Y (Bourns Inc.), MFBW1V2012-600-R (Eaton - Electronics Division), and MMZ1608R600ATA00 (TDK Corporation). The original MMZ2012R600AT000 and MMZ2012Y600BT000 are both Last Time Buy status, indicating limited future availability.
Q: Can impedance tolerance variants (50 Ohm or 70 Ohm) be used without circuit redesign?
A: Impedance tolerance variants require verification that the application circuit design permits ±10 Ohm impedance deviation. If the circuit is impedance-sensitive (such as in high-frequency signal conditioning), substitution with non-60 Ohm parts may require circuit analysis and testing. If the application has documented impedance tolerance specifications, substitution is permissible within those limits.
Alternative Parts
SJ6012L2TP
Littelfuse Inc.
6 Alternative Parts
JMK107BBJ476MA-RE
Taiyo Yuden
10 Alternative Parts
GMK107BBJ475MA-T
Taiyo Yuden
5 Alternative Parts
SJ6020N2ARP
Littelfuse Inc.
3 Alternative Parts
SJ6025R2ATP
Littelfuse Inc.
4 Alternative Parts
2474-05L
API Delevan Inc.
1 Alternative Parts
4590R-684K
API Delevan Inc.
1 Alternative Parts
CM6560R-334
API Delevan Inc.
1 Alternative Parts
CM6460-104
API Delevan Inc.
1 Alternative Parts
5526-12
API Delevan Inc.
1 Alternative Parts