MLF14FTC750R Equivalent & Substitute Parts

Part Overview

The MLF14FTC750R is a 750 Ohm ±1% 1/4W MELF 0204 thin film chip resistor manufactured by Stackpole Electronics Inc. This component is actively produced and widely used in precision analog circuits requiring stable resistance values with tight tolerance specifications. Substitute parts are identified to provide alternative sourcing options when the primary part is unavailable or when design requirements permit higher power ratings or enhanced environmental specifications.

Substiute Parts

MLF14FTC750R

Stackpole Electronics IncIn Stock: 983MLF14FTC750R Datasheet

Current PartRFQ

MMA02040C7500FB300

Vishay Beyschlag/Draloric/BC ComponentsIn Stock: 16222MMA02040C7500FB300 Datasheet

UpgradeRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution of the MLF14FTC750R is permissible when the following criteria are met:

• Resistance value remains 750 Ohms with ±1% tolerance
• Package type is MELF 0204 (identical mechanical and electrical footprint)
• Composition is thin film (maintains temperature coefficient and stability characteristics)
• Temperature coefficient is ±50ppm/°C or better
• Operating temperature range covers -55°C to 155°C minimum
• RoHS3 compliance is maintained
• MSL rating is 1 or equivalent

The substitute part MMA02040C7500FB300 meets all these criteria. The primary difference is an increased power rating (0.4W versus 0.25W), which represents an upgrade in thermal capability without affecting electrical performance in applications designed for the original 0.25W specification.

Parameter Comparison

Engineering Selection Recommendations

Both the MLF14FTC750R and MMA02040C7500FB300 are active production components with full RoHS3 compliance and REACH unaffected status, making them suitable for current and future regulatory requirements.

The MMA02040C7500FB300 includes AEC-Q200 automotive qualification and anti-sulfur coating, providing enhanced reliability in harsh environments. This upgrade is applicable in designs where automotive-grade components or extended environmental protection is specified.

The dimensional difference (0.138" versus 0.142" length) is within typical MELF 0204 manufacturing tolerances and does not affect PCB footprint compatibility. The increased power rating of the substitute part provides additional thermal margin without compromising electrical characteristics.

Selection between these parts should be based on availability, supply chain requirements, and whether automotive qualification or anti-sulfur protection is mandated by the application specification.

Frequently Asked Questions (FAQ)

Q: Can MMA02040C7500FB300 be used as a direct replacement for MLF14FTC750R?

A: Yes. Both components share identical resistance, tolerance, package type, composition, temperature coefficient, and operating temperature range. The substitute has a higher power rating, which is compatible with applications designed for the original 0.25W specification.

Q: What is the significance of the 0.4W power rating on the substitute part?

A: The higher power rating indicates greater thermal dissipation capability. In applications where the original 0.25W rating is sufficient, the 0.4W rated component will operate at lower junction temperature, potentially extending component life. This does not change the electrical behavior in the circuit.

Q: Are there dimensional compatibility concerns?

A: The length difference (0.138" to 0.142") is within standard MELF 0204 tolerances. Both components have identical diameter (0.055") and use the same 0204 package designation. PCB footprints designed for MELF 0204 will accommodate both parts without modification.

Q: Does the anti-sulfur coating on the substitute affect circuit performance?

A: No. Anti-sulfur coating is a protective feature that enhances reliability in corrosive environments but does not alter electrical characteristics. The coating is transparent to circuit operation.

Q: What is the difference between ROHS3 compliance on both parts?

A: Both components meet ROHS3 standards. This certification confirms the absence of restricted substances (lead, cadmium, mercury, hexavalent chromium, PBBs, PBDEs) and is required for most commercial and industrial applications.

Q: Is AEC-Q200 qualification required for my application?

A: AEC-Q200 is an automotive industry standard for passive components. It is required only if your application is automotive or subject to automotive-grade specifications. For non-automotive applications, both parts are functionally equivalent.