MAX4513ESE Equivalent & Substitute Parts

Part Overview

The MAX4513ESE is a 4-circuit IC switch with SPST NO/NC configuration, 160Ohm on-state resistance, and 16-SOIC packaging manufactured by Analog Devices Inc./Maxim Integrated. This part is classified as obsolete, which necessitates identification of functionally equivalent alternatives for new designs and ongoing production requirements. The device operates across a wide supply voltage range (9V–36V single supply, ±4.5V–18V dual supply) and is suitable for signal routing and multiplexing applications in industrial and consumer electronics.

Key Parameters

Parameter	MAX4513ESE
Switch Circuit Configuration	SPST - NO/NC
Number of Circuits	4
Multiplexer/Demultiplexer Circuit	1:1
On-State Resistance (Max)	160Ohm
Voltage - Supply, Single (V+)	9V ~ 36V
Voltage - Supply, Dual (V±)	±4.5V ~ 18V
Switch Time Ton (Max)	500ns
Switch Time Toff (Max)	400ns
Charge Injection	1.5pC
Channel Capacitance CS(off)	10pF
Channel Capacitance CD(off)	5pF
Current - Leakage IS(off) (Max)	500pA
Crosstalk	-66dB @ 1MHz
Operating Temperature	-40°C ~ 85°C
Package / Case	16-SOIC (0.154", 3.90mm Width)
Product Status	Obsolete
RoHS Status	RoHS non-compliant

Substitute Part Grouping Explanation

Substitution of the MAX4513ESE is determined by strict alignment of the following electrical and mechanical parameters:

Primary Substitution Criteria:

Switch circuit configuration (SPST - NO/NC)
Number of circuits (4)
Multiplexer/demultiplexer ratio (1:1)
Package type (16-SOIC)
Operating temperature range compatibility
Supply voltage range compatibility

Secondary Compatibility Factors:

On-state resistance tolerance
Switch timing characteristics
Leakage current specifications
Crosstalk performance

Substitute parts are grouped into three categories based on on-state resistance characteristics and supply voltage requirements:

Group 1: Direct Packaging Variants (MAX4513 Family) MAX4513ESE+ represents the active production equivalent with identical electrical specifications but improved RoHS3 compliance and Tube packaging.

Group 2: Lower On-State Resistance Alternatives (ADG513 Family) ADG513BRZ and ADG513BRZ-REEL offer significantly lower on-state resistance (30Ohm typical) but operate at reduced supply voltages (3V–5.5V single, ±4.5V–5.5V dual). These are suitable only for applications where lower supply voltages are acceptable.

Group 3: Higher Performance Alternatives ADG1313YRZ and ADG1313YRZ-REEL provide improved switching speed (125ns/50ns vs. 500ns/400ns), lower leakage current (10nA vs. 500pA), and extended temperature range (-40°C to 105°C), but operate at fixed supply voltages (12V single, ±15V dual) and higher on-state resistance (200Ohm).

Group 4: Lowest On-State Resistance Option DG456EY-T1-E3 (Vishay Siliconix) delivers the lowest on-state resistance (5.3Ohm) with fast switching times (118ns/97ns) and operates across 12V–36V single supply or ±5V–15V dual supply, but exhibits higher charge injection (22pC) and channel capacitance.

Group 5: Legacy Alternative LTC203CS#TRPBF (Analog Devices) provides 125Ohm on-state resistance with fixed 5V single supply or ±15V dual supply operation, suitable only for applications with these specific voltage requirements.

Parameter Comparison

Parameter	MAX4513ESE	MAX4513ESE+	ADG513BRZ	ADG513BRZ-REEL	ADG513BRZ-REEL7	ADG1313YRZ	ADG1313YRZ-REEL7	DG456EY-T1-E3	LTC203CS#TRPBF
Switch Circuit	SPST - NO/NC	SPST - NO/NC	SPST - NO/NC	SPST - NO/NC	SPST - NO/NC	SPST - NO/NC	SPST - NO/NC	SPST - NO/NC	SPST - NO/NC
Number of Circuits	4	4	4	4	4	4	4	4	4
Multiplexer Ratio	1:1	1:1	1:1	1:1	1:1	1:1	1:1	1:1	1:1
On-State Resistance (Max)	160Ohm	160Ohm	30Ohm (Typ)	30Ohm (Typ)	30Ohm (Typ)	200Ohm	200Ohm	5.3Ohm	125Ohm
V+ Supply Range	9V ~ 36V	9V ~ 36V	3V ~ 5.5V	3V ~ 5.5V	3V ~ 5.5V	12V	12V	12V ~ 36V	5V
V± Supply Range	±4.5V ~ 18V	±4.5V ~ 18V	±4.5V ~ 5.5V	±4.5V ~ 5.5V	±4.5V ~ 5.5V	±15V	±15V	±5V ~ 15V	±15V
Switch Time Ton (Max)	500ns	500ns	200ns	200ns	200ns	125ns	125ns	118ns	400ns
Switch Time Toff (Max)	400ns	400ns	120ns (Typ)	120ns (Typ)	120ns (Typ)	50ns	50ns	97ns	300ns
Charge Injection	1.5pC	1.5pC	11pC	11pC	11pC	2pC	2pC	22pC	8pC
Current - Leakage IS(off) (Max)	500pA	500pA	100pA	100pA	100pA	10nA	10nA	500pA	5nA
Crosstalk	-66dB @ 1MHz	-66dB @ 1MHz	-85dB @ 1MHz	-85dB @ 1MHz	-85dB @ 1MHz	-90dB @ 1MHz	-90dB @ 1MHz	-85dB @ 1MHz	-90dB @ 100kHz
Operating Temperature	-40°C ~ 85°C	-40°C ~ 85°C	-40°C ~ 85°C	-40°C ~ 85°C	-40°C ~ 85°C	-40°C ~ 105°C	-40°C ~ 105°C	-40°C ~ 125°C	0°C ~ 70°C
Package / Case	16-SOIC	16-SOIC	16-SOIC	16-SOIC	16-SOIC	16-SOIC	16-SOIC	16-SOIC	16-SOIC
RoHS Status	Non-compliant	ROHS3 Compliant	ROHS3 Compliant	ROHS3 Compliant	ROHS3 Compliant	ROHS3 Compliant	ROHS3 Compliant	ROHS3 Compliant	ROHS3 Compliant
Product Status	Obsolete	Active	Active	Active	Active	Active	Active	Active	Active

Engineering Selection Recommendations

For Direct Replacement (Recommended Primary Path): MAX4513ESE+ is the preferred substitute. It maintains identical electrical specifications and 16-SOIC packaging while transitioning to active production status and ROHS3 compliance. This option requires no circuit redesign and preserves all performance characteristics of the original MAX4513ESE.

For Low-Voltage Applications (3V–5.5V Supply): ADG513BRZ, ADG513BRZ-REEL, or ADG513BRZ-REEL7 are suitable only if your application operates exclusively within 3V–5.5V supply ranges. These parts offer lower on-state resistance (30Ohm typical) and faster switching times (200ns/120ns typical) but are incompatible with the original part's 9V–36V supply range. All three variants are ROHS3 compliant and in active production.

For Fixed 12V/±15V Supply Systems: ADG1313YRZ or ADG1313YRZ-REEL7 provide superior switching performance (125ns/50ns) and extended temperature range (-40°C to 105°C) but operate only at fixed 12V single supply or ±15V dual supply. These are suitable for applications where supply voltage is constrained to these values and faster switching is beneficial.

For Lowest On-State Resistance Requirement: DG456EY-T1-E3 (Vishay Siliconix) delivers the lowest on-state resistance (5.3Ohm) with fast switching (118ns/97ns) and operates across 12V–36V or ±5V–15V ranges. This part is ROHS3 compliant and rated to 125°C. Selection requires acceptance of higher charge injection (22pC) and channel capacitance characteristics.

For Fixed 5V/±15V Supply Systems: LTC203CS#TRPBF operates only at 5V single supply or ±15V dual supply with 125Ohm on-state resistance. This part is suitable only for legacy systems with these specific voltage constraints and is ROHS3 compliant with active production status.

Compliance Considerations: All substitute parts except the original MAX4513ESE are ROHS3 compliant. For applications requiring RoHS compliance, MAX4513ESE+ is the mandatory choice among MAX4513 family variants. All substitutes carry REACH Unaffected status where specified.

Frequently Asked Questions (FAQ)

Q: Can MAX4513ESE+ be used as a direct drop-in replacement for MAX4513ESE?

A: Yes. MAX4513ESE+ is electrically and mechanically identical to MAX4513ESE, with the same 160Ohm on-state resistance, 9V–36V supply range, and 16-SOIC package. The primary differences are active production status and ROHS3 compliance. No circuit modifications are required.

Q: What is the key difference between MAX4513ESE and ADG513BRZ variants?

A: The primary difference is supply voltage range. MAX4513ESE operates at 9V–36V (single) or ±4.5V–18V (dual), while ADG513BRZ operates at 3V–5.5V (single) or ±4.5V–5.5V (dual). ADG513BRZ also has lower on-state resistance (30Ohm typical vs. 160Ohm) and faster switching times. These parts are not interchangeable in circuits designed for higher supply voltages.

Q: Are all substitute parts available in the same 16-SOIC package?

A: Yes. All substitute parts listed are available in 16-SOIC (0.154", 3.90mm width) packaging, ensuring mechanical compatibility with the original MAX4513ESE footprint.

Q: Which substitute offers the best overall performance?

A: Performance depends on application requirements. ADG1313YRZ offers the fastest switching times (125ns/50ns) and lowest leakage current (10nA), but operates only at fixed 12V/±15V supplies. DG456EY-T1-E3 offers the lowest on-state resistance (5.3Ohm) with fast switching and wider supply range (12V–36V), but exhibits higher charge injection. MAX4513ESE+ maintains the original specifications with improved compliance.

Q: Can I use ADG1313YRZ in a circuit designed for MAX4513ESE?

A: Only if your circuit operates at exactly 12V single supply or ±15V dual supply. ADG1313YRZ is not compatible with the original part's 9V–36V supply range. Additionally, the higher on-state resistance (200Ohm vs. 160Ohm) may affect signal routing performance in some applications.

Q: What is the operating temperature difference between MAX4513ESE and its substitutes?

A: MAX4513ESE operates from -40°C to 85°C. ADG513 variants maintain this range. ADG1313 variants extend to -40°C to 105°C. DG456EY-T1-E3 extends to -40°C to 125°C. LTC203CS#TRPBF is limited to 0°C to 70°C. Select based on your application's thermal requirements.

Q: Are packaging variants (Tube vs. Tape & Reel) electrically equivalent?

A: Yes. Packaging variants of the same part number (e.g., ADG513BRZ vs. ADG513BRZ-REEL vs. ADG513BRZ-REEL7) are electrically identical. The suffix indicates packaging format only: standard Tube, Tape & Reel (TR), or Tape & Reel 7-inch reel. Select based on your procurement and assembly requirements.

Q: Which substitute is best for new designs?

A: MAX4513ESE+ is recommended for new designs requiring the original specifications with modern compliance. For new designs with flexibility in supply voltage, ADG513BRZ (3V–5.5V) or DG456EY-T1-E3 (12V–36V) offer improved performance characteristics. Evaluate your specific supply voltage, switching speed, and on-state resistance requirements.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message