MAX4294EUD+ Equivalent & Substitute Parts Reference

Part Overview

The MAX4294EUD+ is a general-purpose operational amplifier integrated circuit manufactured by Analog Devices Inc./Maxim Integrated. This device features four independent amplifier circuits in a 14-TSSOP surface-mount package with rail-to-rail output capability. The part is classified as Active product status with full RoHS3 compliance and REACH unaffected designation. Substitute parts are identified when original inventory becomes unavailable, when alternative packaging formats are required for manufacturing processes, or when enhanced performance characteristics are needed for specific application requirements while maintaining functional compatibility within the 14-TSSOP package footprint.

Key Parameters

Parameter	Value	Unit
Manufacturer	Analog Devices Inc./Maxim Integrated	—
Part Number	MAX4294EUD+	—
Category	Linear, Amplifiers	—
Amplifier Type	General Purpose	—
Number of Circuits	4	—
Output Type	Rail-to-Rail	—
Package / Case	14-TSSOP (0.173", 4.40mm Width)	—
Mounting Type	Surface Mount	—
Voltage - Supply Span (Min)	1.8	V
Voltage - Supply Span (Max)	5.5	V
Operating Temperature	-40 to 85	°C
Slew Rate	0.2	V/µs
Gain Bandwidth Product	500	kHz
Current - Input Bias	15	nA
Voltage - Input Offset	200	µV
Current - Supply	100	µA (x4 Channels)
Current - Output / Channel	20	mA
RoHS Status	ROHS3 Compliant	—
Moisture Sensitivity Level (MSL)	1 (Unlimited)	—

Substitute Part Grouping Explanation

Substitution compatibility for the MAX4294EUD+ is determined by the following critical parameters: four-circuit configuration, rail-to-rail output architecture, 14-TSSOP package geometry, surface-mount technology, supply voltage range spanning 1.8 V to 5.5 V, and operating temperature range of -40°C to 85°C. All substitute parts maintain these core specifications. Substitute parts are grouped into two categories based on amplifier technology type: General Purpose amplifiers (matching the original MAX4294EUD+ classification) and CMOS amplifiers (offering enhanced performance characteristics). Within each category, parts are further differentiated by packaging format (Tube, Tape & Reel, Cut Tape, or Bulk) and performance metrics including slew rate, gain bandwidth product, input bias current, and supply current consumption. The 14-TSSOP package footprint remains constant across all substitutes, ensuring mechanical and electrical compatibility with existing printed circuit board layouts.

Parameter Comparison

Part Number	Manufacturer	Amplifier Type	Number of Circuits	Output Type	Package	Slew Rate (V/µs)	GBW (kHz)	Input Bias (pA/nA)	Input Offset (µV)	Supply Current (µA)	Output Current (mA)	Voltage Min (V)	Voltage Max (V)	Temp Range (°C)	Packaging Format
MAX4294EUD+	Analog Devices/Maxim	General Purpose	4	Rail-to-Rail	14-TSSOP	0.2	500	15 nA	200	100	20	1.8	5.5	-40 to 85	Tube
AD8619WARUZ-RL	Analog Devices	CMOS	4	Rail-to-Rail	14-TSSOP	0.1	400	0.2 pA	400	38	80	1.8	5.0	-40 to 125	Tape & Reel
OPA4313IPW	Texas Instruments	CMOS	4	Rail-to-Rail	14-TSSOP	0.5	1000	0.2 pA	500	50	15	1.8	5.5	-40 to 125	Tube
OPA4313IPWR	Texas Instruments	CMOS	4	Rail-to-Rail	14-TSSOP	0.5	1000	0.2 pA	500	50	15	1.8	5.5	-40 to 125	Cut Tape & Digi-Reel
OPA4314AIPW	Texas Instruments	CMOS	4	Rail-to-Rail	14-TSSOP	1.5	3000	1 pA	500	150	20	1.8	5.5	-40 to 125	Bulk
OPA4314AIPWR	Texas Instruments	CMOS	4	Rail-to-Rail	14-TSSOP	1.5	3000	1 pA	500	150	20	1.8	5.5	-40 to 125	Cut Tape & Digi-Reel
OPA4344EA/2K5	Texas Instruments	CMOS	4	Rail-to-Rail	14-TSSOP	0.8	1000	0.2 pA	200	150	15	2.5	5.5	-40 to 85	—

Engineering Selection Recommendations

Selection of substitute parts for the MAX4294EUD+ must be based on compliance certifications, product status, and electrical parameter compatibility within the specified operating envelope. All listed substitute parts maintain Active product status and RoHS3 compliance, ensuring regulatory alignment with current manufacturing standards. The AD8619WARUZ-RL, OPA4313IPW, OPA4313IPWR, OPA4314AIPW, OPA4314AIPWR, and OPA4344EA/2K5 are qualified substitutes that preserve the four-circuit rail-to-rail architecture and 14-TSSOP package footprint.

For applications requiring direct performance equivalence with minimal parameter deviation, the OPA4313 series (OPA4313IPW and OPA4313IPWR) provides enhanced slew rate (0.5 V/µs versus 0.2 V/µs) and doubled gain bandwidth product (1 MHz versus 500 kHz) while maintaining compatible supply voltage ranges and operating temperature specifications to -40°C to 125°C. These parts are available in Tube and Cut Tape & Digi-Reel packaging formats.

For applications demanding superior dynamic performance, the OPA4314A series (OPA4314AIPW and OPA4314AIPWR) delivers 1.5 V/µs slew rate and 3 MHz gain bandwidth product with extended operating temperature range to 125°C. These parts are available in Bulk and Cut Tape & Digi-Reel formats.

The AD8619WARUZ-RL offers ultra-low input bias current (0.2 pA) and reduced supply current (38 µA) in Tape & Reel packaging, suitable for applications prioritizing power efficiency and input impedance characteristics. Note that maximum supply voltage is limited to 5.0 V.

The OPA4344EA/2K5 maintains input offset voltage matching the original part (200 µV) with moderate slew rate (0.8 V/µs) and 1 MHz gain bandwidth product. Minimum supply voltage requirement is 2.5 V, which may restrict use in ultra-low-voltage applications below 1.8 V.

Packaging format selection (Tube, Tape & Reel, Cut Tape, or Bulk) depends on manufacturing process requirements and component handling systems. All substitutes maintain identical 14-TSSOP footprint geometry and surface-mount compatibility.

Frequently Asked Questions (FAQ)

Q1: Can OPA4313IPWR be used as a direct replacement for MAX4294EUD+ in existing circuit designs?

A: OPA4313IPWR maintains functional compatibility through identical four-circuit configuration, rail-to-rail output, 14-TSSOP package, and overlapping supply voltage range (1.8 V to 5.5 V). The part offers enhanced performance with 0.5 V/µs slew rate and 1 MHz gain bandwidth product. Circuit validation is required to confirm performance adequacy for specific application parameters.

Q2: What is the primary difference between OPA4313 and OPA4314A series substitutes?

A: The OPA4314A series provides superior dynamic performance with 1.5 V/µs slew rate and 3 MHz gain bandwidth product compared to OPA4313 specifications of 0.5 V/µs and 1 MHz. OPA4314A also features lower input bias current (1 pA versus 0.2 pA) and higher output current capability (20 mA per channel). Both series maintain compatible supply voltage ranges and extended operating temperature to 125°C.

Q3: Why does AD8619WARUZ-RL have a maximum supply voltage of 5.0 V instead of 5.5 V?

A: The AD8619WARUZ-RL is specified with 5.0 V maximum supply voltage as a design parameter of this particular device variant. Applications requiring 5.5 V operation must select alternative substitutes such as OPA4313 or OPA4314A series parts.

Q4: What packaging format should be selected for high-volume manufacturing?

A: Cut Tape & Digi-Reel format (OPA4313IPWR, OPA4314AIPWR) is optimized for automated pick-and-place assembly processes in high-volume production. Tape & Reel format (AD8619WARUZ-RL) is suitable for continuous feed systems. Tube packaging (MAX4294EUD+, OPA4313IPW, OPA4314AIPW) is appropriate for lower-volume or manual assembly operations.

Q5: Are all substitute parts RoHS3 compliant?

A: All listed substitute parts maintain RoHS3 compliance and REACH unaffected status, ensuring regulatory alignment with current environmental and hazardous substance restrictions.

Q6: Can OPA4344EA/2K5 be used in applications requiring 1.8 V minimum supply voltage?

A: No. OPA4344EA/2K5 specifies 2.5 V minimum supply voltage, which exceeds the 1.8 V lower limit of the original MAX4294EUD+. Applications requiring operation at 1.8 V must select OPA4313, OPA4314A, or AD8619WARUZ-RL variants.

Q7: What is the moisture sensitivity level (MSL) consideration for substitute selection?

A: MAX4294EUD+ and OPA4344EA/2K5 specify MSL 1 (Unlimited), indicating no moisture sensitivity restrictions. AD8619WARUZ-RL specifies MSL 3 (168 Hours), requiring controlled storage and handling. OPA4313 and OPA4314A series specify MSL 2 (1 Year). MSL classification affects component shelf life and storage requirements in manufacturing environments.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message