MAX313ESE Equivalent & Substitute Parts

Part Overview

The MAX313ESE is a 4-circuit SPST-NO IC switch manufactured by Analog Devices Inc./Maxim Integrated, housed in a 16-SOIC surface mount package. This component is classified as obsolete, making equivalent and substitute parts necessary for ongoing design support and production continuity. The MAX313ESE operates across a wide supply voltage range (4.5V to 30V single supply, ±4.5V to ±20V dual supply) with a maximum on-state resistance of 10Ohm and switching times of 225ns (Ton) and 185ns (Toff).

Key Parameters

Parameter	Value
Switch Circuit Type	SPST - NO (Single Pole Single Throw - Normally Open)
Number of Circuits	4
Multiplexer/Demultiplexer Configuration	1:1
On-State Resistance (Max)	10Ohm
Channel-to-Channel Matching (ΔRon)	300mOhm
Voltage - Supply, Single (V+)	4.5V ~ 30V
Voltage - Supply, Dual (V±)	±4.5V ~ 20V
Switch Time (Ton, Toff) (Max)	225ns, 185ns
Charge Injection	20pC
Channel Capacitance (CS(off), CD(off))	15pF, 15pF
Current - Leakage (IS(off)) (Max)	500pA
Crosstalk	-85dB @ 1MHz
Operating Temperature	-40°C ~ 85°C (TA)
Package / Case	16-SOIC (0.154", 3.90mm Width)
RoHS Status	ROHS3 Compliant
Moisture Sensitivity Level (MSL)	1 (Unlimited)

Substitute Part Grouping Explanation

Substitution for the MAX313ESE is determined by strict adherence to the following electrical and mechanical parameters:

Primary Substitution Criteria:

Switch circuit type: SPST - NO
Number of circuits: 4
Multiplexer configuration: 1:1
Package type: 16-SOIC surface mount
Operating temperature range: -40°C ~ 85°C
RoHS3 compliance and MSL 1 rating

Secondary Compatibility Parameters:

On-state resistance tolerance (parts with ≤10Ohm maximum are direct substitutes; higher resistance values require application-specific evaluation)
Supply voltage compatibility (parts must support the required voltage rails for the application)
Switching speed (Ton/Toff parameters must meet application timing requirements)
Leakage current and crosstalk specifications

Substitute parts are grouped into three categories based on on-state resistance characteristics: low-resistance variants (5Ohm), medium-resistance variants (10Ohm equivalent packaging), and higher-resistance alternatives (24Ohm, 35Ohm, 135Ohm).

Parameter Comparison

Part Number	Manufacturer	Product Status	On-State Resistance (Max)	ΔRon	V+ Supply	V± Supply	Ton/Toff (Max)	Charge Injection	IS(off) (Max)	Crosstalk	Package	Packaging Type
MAX313ESE	Analog Devices Inc./Maxim Integrated	Obsolete	10Ohm	300mOhm	4.5V ~ 30V	±4.5V ~ 20V	225ns, 185ns	20pC	500pA	-85dB @ 1MHz	16-SOIC	-
MAX313ESE+	Analog Devices Inc./Maxim Integrated	Active	10Ohm	300mOhm	4.5V ~ 30V	±4.5V ~ 20V	225ns, 185ns	20pC	500pA	-85dB @ 1MHz	16-SOIC	Tube
ADG452BRZ	Analog Devices Inc.	Active	5Ohm	100mOhm	12V	±4.5V ~ 20V	180ns, 140ns	20pC	500pA	-90dB @ 1MHz	16-SOIC	Tube
ADG452BRZ-REEL	Analog Devices Inc.	Active	5Ohm	100mOhm	12V	±4.5V ~ 20V	180ns, 140ns	20pC	500pA	-90dB @ 1MHz	16-SOIC	Tape & Reel (TR)
ADG452BRZ-REEL7	Analog Devices Inc.	Active	5Ohm	100mOhm	12V	±4.5V ~ 20V	180ns, 140ns	20pC	500pA	-90dB @ 1MHz	16-SOIC	Cut Tape (CT) & Digi-Reel®
ADG432BRZ	Analog Devices Inc.	Active	24Ohm	1.2Ohm	12V	±15V	90ns, 60ns	5pC	250pA	-85dB @ 1MHz	16-SOIC	Tube
ADG432BRZ-REEL	Analog Devices Inc.	Active	24Ohm	1.2Ohm	12V	±15V	90ns, 60ns	5pC	250pA	-85dB @ 1MHz	16-SOIC	Cut Tape (CT) & Digi-Reel®
DG412DY-E3	Vishay Siliconix	Active	35Ohm	-	5V ~ 44V	±5V ~ 20V	175ns, 145ns	5pC	250pA	-85dB @ 1MHz	16-SOIC	Tube
DG412DY-T1-E3	Vishay Siliconix	Active	35Ohm	-	5V ~ 44V	±5V ~ 20V	175ns, 145ns	5pC	250pA	-85dB @ 1MHz	16-SOIC	Cut Tape (CT) & Digi-Reel®
ALD4212SCL	Advanced Linear Devices Inc.	Active	135Ohm	2.7Ohm	3V ~ 12V	±1.5V ~ 6V	130ns, 130ns	0.2pC	100pA	-90dB @ 100kHz	16-SOIC	Tube

Engineering Selection Recommendations

Direct Replacement (Active Status): MAX313ESE+ is the direct active equivalent of the obsolete MAX313ESE, maintaining identical electrical specifications and 16-SOIC packaging. Both parts are ROHS3 compliant with MSL 1 rating. Selection between tube and alternative packaging formats (Tape & Reel) depends on procurement and assembly requirements.

Low-Resistance Alternatives (5Ohm): The ADG452BRZ family (ADG452BRZ, ADG452BRZ-REEL, ADG452BRZ-REEL7) offers superior on-state resistance (5Ohm vs. 10Ohm) with improved channel matching (100mOhm vs. 300mOhm) and faster switching times (180ns/140ns vs. 225ns/185ns). These parts are active and ROHS3 compliant. Selection among variants depends on packaging requirements: tube for standard procurement, Tape & Reel (TR) or Cut Tape & Digi-Reel® for high-volume automated assembly. Note: V+ supply is limited to 12V, requiring application voltage compatibility verification.

Medium-Resistance Alternatives (24Ohm): The ADG432BRZ family (ADG432BRZ, ADG432BRZ-REEL) provides faster switching performance (90ns/60ns) with reduced charge injection (5pC vs. 20pC) but higher on-state resistance (24Ohm). These parts support ±15V dual supply operation. Suitable for applications where lower resistance is not critical and faster switching is beneficial. Both variants are active and ROHS3 compliant.

Higher-Resistance Alternatives (35Ohm, 135Ohm): DG412DY-E3 and DG412DY-T1-E3 (Vishay Siliconix, 35Ohm) support extended V+ supply range (5V ~ 44V) with comparable switching performance. ALD4212SCL (Advanced Linear Devices, 135Ohm) operates at lower supply voltages (3V ~ 12V single, ±1.5V ~ 6V dual) with minimal charge injection (0.2pC) and leakage current (100pA). These alternatives are suitable only for applications where higher on-state resistance is acceptable.

All substitute parts maintain 16-SOIC packaging, -40°C ~ 85°C operating temperature range, and ROHS3 compliance with MSL 1 rating.

Frequently Asked Questions (FAQ)

Q: Can MAX313ESE+ be used as a direct replacement for MAX313ESE? A: Yes. MAX313ESE+ is the active equivalent with identical electrical specifications (10Ohm on-state resistance, 4.5V ~ 30V single supply, ±4.5V ~ 20V dual supply, 225ns/185ns switching times) and 16-SOIC packaging. The primary difference is product status (active vs. obsolete) and packaging format (tube).

Q: What is the key difference between ADG452BRZ variants? A: ADG452BRZ, ADG452BRZ-REEL, and ADG452BRZ-REEL7 are electrically identical with 5Ohm on-state resistance. Differences are packaging formats: tube (standard), Tape & Reel (TR), and Cut Tape & Digi-Reel® (CT). Selection depends on procurement and assembly automation requirements.

Q: Can ADG452BRZ replace MAX313ESE in all applications? A: ADG452BRZ offers superior performance (5Ohm vs. 10Ohm resistance, faster switching) but has a restricted V+ supply range (12V only vs. 4.5V ~ 30V). Substitution is valid only if the application operates at 12V single supply or within the ±4.5V ~ 20V dual supply range.

Q: What are the supply voltage constraints for each substitute family? A: MAX313ESE+ and ADG452BRZ family: 4.5V ~ 30V (single) or ±4.5V ~ 20V (dual). ADG432BRZ family: 12V (single) or ±15V (dual). DG412DY variants: 5V ~ 44V (single) or ±5V ~ 20V (dual). ALD4212SCL: 3V ~ 12V (single) or ±1.5V ~ 6V (dual). Verify application voltage requirements before selection.

Q: Are all substitute parts ROHS3 compliant? A: Yes. All listed substitute parts are ROHS3 compliant with MSL 1 (Unlimited) moisture sensitivity level, matching the compliance profile of MAX313ESE.

Q: Which substitute offers the fastest switching performance? A: ADG432BRZ family provides the fastest switching times (90ns Ton, 60ns Toff) compared to MAX313ESE (225ns Ton, 185ns Toff). This comes at the cost of higher on-state resistance (24Ohm) and restricted supply voltage (12V single, ±15V dual).

Q: Can higher-resistance alternatives (DG412DY, ALD4212SCL) be used as drop-in replacements? A: No. These parts have significantly higher on-state resistance (35Ohm and 135Ohm respectively) and different supply voltage ranges. Use only if application design explicitly tolerates the higher resistance and operates within the specified voltage ranges.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message