MAL213635331E3 Equivalent & Substitute Parts

Part Overview

The MAL213635331E3 is a 330 µF, 16 V aluminum electrolytic capacitor in radial configuration manufactured by Vishay Beyschlag/Draloric/BC Components. This component is rated for 4000 hours at 105°C and is classified as Active in product status. The part is designed for general-purpose applications requiring polarized capacitive energy storage in through-hole mounting configurations.

Substitute parts become necessary when the original component reaches end-of-life status, inventory constraints occur, or when design requirements allow for enhanced electrical performance characteristics such as increased voltage rating or extended operational lifetime.

Substiute Parts

MAL213635331E3

Vishay Beyschlag/Draloric/BC ComponentsIn Stock: 1275MAL213635331E3 Datasheet

Current PartRFQ

ELXZ250ELL331MJC5S

Chemi-ConIn Stock: 2801ELXZ250ELL331MJC5S Datasheet

UpgradeRFQ

UPJ1C331MPD6

NichiconIn Stock: 3005UPJ1C331MPD6 Datasheet

UpgradeRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the MAL213635331E3 is determined by the following critical parameters:

Mandatory Matching Parameters:

• Capacitance: 330 µF (exact match required)
• Tolerance: ±20% (exact match required)
• Polarization: Polar (exact match required)
• Mounting Type: Through Hole (exact match required)
• Package Type: Radial, Can (exact match required)
• Lead Spacing: 0.197" (5.00 mm) (exact match required)
• Case Diameter: 0.394" (10.00 mm) (exact match required)

Allowable Variation Parameters:

• Voltage Rating: May be equal to or greater than 16 V
• Lifetime @ 105°C: May be equal to or greater than 4000 Hrs
• Height (Max): May be equal to or slightly greater than 0.531" (14.60 mm) within PCB layout constraints
• Impedance: May vary based on manufacturer design
• Ripple Current: May vary based on manufacturer design

Two substitute parts meet these criteria and are listed below.

Parameter Comparison

Engineering Selection Recommendations

ELXZ250ELL331MJC5S (Chemi-Con LXZ Series)

This substitute provides a voltage rating upgrade from 16 V to 25 V and extended lifetime of 5000 hours at 105°C compared to the original 4000 hours. The part carries AEC-Q200 automotive qualification and is classified as Active in product status. The increased voltage margin provides additional design safety. Height increases from 14.60 mm to 14.00 mm; verify PCB layout clearance before selection. Impedance is reduced to 90 mOhms, offering improved high-frequency ripple current performance.

UPJ1C331MPD6 (Nichicon UPJ Series)

This substitute maintains the original 16 V voltage rating while providing extended lifetime of 5000 hours at 105°C. The part is classified as Not For New Designs in product status. Height increases from 14.60 mm to 14.00 mm; verify PCB layout clearance before selection. Impedance is 180 mOhms. This option is suitable for replacement applications where voltage rating equivalence is prioritized and new design constraints do not apply.

Frequently Asked Questions (FAQ)

Q: Can ELXZ250ELL331MJC5S be used as a direct replacement for MAL213635331E3?

A: Yes. Both parts share identical capacitance (330 µF), tolerance (±20%), polarization (Polar), mounting type (Through Hole), package type (Radial, Can), lead spacing (5.00 mm), and case diameter (10.00 mm). The substitute provides higher voltage rating (25 V vs. 16 V) and extended lifetime (5000 Hrs vs. 4000 Hrs). Height increases from 14.60 mm to 14.00 mm; confirm PCB layout accommodates this dimension.

Q: Can UPJ1C331MPD6 be used as a direct replacement for MAL213635331E3?

A: Yes. Both parts share identical capacitance (330 µF), tolerance (±20%), voltage rating (16 V), polarization (Polar), mounting type (Through Hole), package type (Radial, Can), lead spacing (5.00 mm), and case diameter (10.00 mm). The substitute provides extended lifetime (5000 Hrs vs. 4000 Hrs). Height increases from 14.60 mm to 14.00 mm; confirm PCB layout accommodates this dimension. Note that this part is classified as Not For New Designs.

Q: What is the significance of the height difference between the original and substitute parts?

A: The original MAL213635331E3 has a maximum seated height of 14.60 mm. Both substitutes have a maximum seated height of 14.00 mm, representing a 0.50 mm increase. This dimension must be verified against PCB layout constraints, component clearance requirements, and enclosure height limitations to ensure mechanical compatibility.

Q: How do impedance differences affect part selection?

A: Impedance values vary among manufacturers due to internal construction differences. The original part has 120 mOhms impedance. ELXZ250ELL331MJC5S offers lower impedance at 90 mOhms, which improves high-frequency ripple current handling. UPJ1C331MPD6 has higher impedance at 180 mOhms. Selection depends on circuit ripple current requirements at operating frequencies.

Q: Are all substitute parts RoHS3 compliant?

A: Yes. The original MAL213635331E3 and both substitute parts (ELXZ250ELL331MJC5S and UPJ1C331MPD6) are ROHS3 Compliant and REACH Unaffected, meeting current environmental regulatory requirements.

Q: What does "Not For New Designs" mean for UPJ1C331MPD6?

A: This product status designation indicates that Nichicon does not recommend this part for new circuit designs. It remains suitable for replacement and repair applications where the part is already in use. For new designs, ELXZ250ELL331MJC5S is the preferred substitute option.