M2T13SA5W13 Toggle Switch SPDT Equivalent & Substitute Parts

Part Overview

The M2T13SA5W13 is a toggle switch manufactured by NKK Switches, classified as SPDT (Single Pole Double Throw) with On-Off-On switching function. This through-hole mounted component is rated for 6A at 125V AC and 3A at 30V DC. The product is currently obsolete, making identification of functionally equivalent alternatives essential for design continuity and component procurement in legacy system maintenance and new designs requiring compatible switching solutions.

Substiute Parts

M2T13SA5W13

NKK SwitchesIn Stock: 928M2T13SA5W13 Datasheet

Current PartRFQ

M2013SA2W13

NKK SwitchesIn Stock: 830M2013SA2W13 Datasheet

SimilarRFQ

100AWSP3T1B4M2QE

E-SwitchIn Stock: 863100AWSP3T1B4M2QE Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitute parts for the M2T13SA5W13 are identified based on strict electrical and mechanical compatibility criteria. The primary substitution parameters are:

• Circuit configuration (SPDT required)
• Switch function (On-Off-On required)
• Current and voltage ratings (must meet or exceed AC 6A/125V and DC 3A/30V)
• Mounting type (Through Hole required)
• Termination style (PC Pin required)
• Actuator type and length (Standard Round, 12.70mm nominal)
• Operating temperature range (-30°C to 85°C minimum)

Two substitute parts meet these criteria with varying degrees of parameter alignment and product status considerations.

Parameter Comparison

Engineering Selection Recommendations

M2013SA2W13 (NKK Switches) provides the closest electrical and mechanical match to the M2T13SA5W13. Both components are manufactured by NKK Switches and share identical circuit configuration, switch function, current ratings, voltage ratings, and operating temperature range. The M2013SA2W13 is currently in active production status, ensuring long-term availability. The actuator length differs by 0.42mm (12.28mm versus 12.70mm), which may require mechanical validation in panel-mounted applications with tight tolerances. The M2013SA2W13 offers extended electrical life (50,000 cycles versus 25,000 cycles), providing improved reliability. This part is the primary substitute for direct replacement scenarios.

100AWSP3T1B4M2QE (E-Switch) meets all core electrical and mechanical substitution criteria with the following considerations: AC current rating is 5A (versus 6A), AC voltage rating is 120V (versus 125V), and DC voltage rating is 28V (versus 30V). These parameters remain within acceptable operational margins for most applications. The E-Switch component offers superior ingress protection (IP67) and extended electrical life (30,000 cycles). This part is suitable for applications requiring enhanced environmental sealing or where the slightly reduced ratings are acceptable.

Both substitute parts maintain ROHS3 compliance and operate within the specified temperature range. Selection between substitutes depends on mechanical fit requirements, environmental exposure conditions, and specific application current/voltage demands.

Frequently Asked Questions (FAQ)

Q: Can the M2013SA2W13 be used as a direct replacement for the M2T13SA5W13?

A: The M2013SA2W13 is electrically and functionally equivalent with identical SPDT configuration, current ratings (6A AC/3A DC), voltage ratings (125V AC/30V DC), and operating temperature range. The actuator length differs by 0.42mm. Mechanical validation is required for panel-mounted applications with tight cutout tolerances or where actuator protrusion is critical.

Q: What are the key differences between the two substitute parts?

A: The M2013SA2W13 (NKK Switches) matches the original part's electrical specifications exactly and is from the same manufacturer. The 100AWSP3T1B4M2QE (E-Switch) has slightly reduced AC ratings (5A/120V) and DC voltage (28V), but offers IP67 ingress protection and higher electrical life (30,000 cycles). Both are active production parts.

Q: Is the 100AWSP3T1B4M2QE suitable for applications rated at 6A 125V AC?

A: The 100AWSP3T1B4M2QE is rated for 5A at 120V AC. Applications requiring the full 6A at 125V AC specification should use the M2013SA2W13. The E-Switch part is suitable for applications with lower current demands or where the voltage margin is acceptable.

Q: What is the significance of the actuator length difference in the M2013SA2W13?

A: The M2013SA2W13 actuator length is 12.28mm compared to 12.70mm in the original part. This 0.42mm difference may affect panel protrusion and user interface feel. Mechanical fit validation is necessary for applications with defined panel cutout dimensions or where actuator engagement depth is specified.

Q: Are both substitute parts RoHS compliant?

A: The 100AWSP3T1B4M2QE is ROHS3 compliant. RoHS status for the M2013SA2W13 is not specified in available documentation. Compliance verification with the manufacturer is recommended if RoHS certification is a procurement requirement.

Q: Which substitute part offers better environmental protection?

A: The 100AWSP3T1B4M2QE provides IP67 ingress protection (dust tight, waterproof), while the M2013SA2W13 does not specify ingress protection. For applications exposed to moisture, dust, or harsh environments, the E-Switch component is the appropriate selection.