M25P80-VMP6TG TR Equivalent & Substitute Parts

Part Overview

The M25P80-VMP6TG TR is a FLASH NOR Memory IC with 8Mbit capacity, SPI interface, and 75 MHz clock frequency manufactured by Micron Technology Inc. This component is classified as obsolete, necessitating identification of functionally compatible alternatives for new designs or production continuity. The part is packaged in 8-VDFPN (6x5) surface mount configuration with RoHS3 compliance and MSL 3 rating.

Substiute Parts

M25P80-VMP6TG TR

Micron Technology Inc.In Stock: 906M25P80-VMP6TG TR Datasheet

Current PartRFQ

MT25QL128ABA1EW7-0SIT TR

Micron Technology Inc.In Stock: 6140MT25QL128ABA1EW7-0SIT TR Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the M25P80-VMP6TG TR is determined by the following critical parameters:

• Voltage supply range compatibility (2.7V ~ 3.6V)
• Operating temperature range (-40°C ~ 85°C)
• Surface mount package with 8-pin VDFN/WDFN configuration
• SPI-based memory interface
• RoHS3 compliance
• MSL 3 rating

The MT25QL128ABA1EW7-0SIT TR qualifies as a substitute based on matching voltage supply, operating temperature, package footprint compatibility, and compliance certifications. While this substitute offers increased memory capacity (128Mbit vs 8Mbit) and enhanced clock frequency (133 MHz vs 75 MHz), these represent functional improvements rather than incompatibilities. The Quad I/O interface is backward compatible with standard SPI operation.

Parameter Comparison

Engineering Selection Recommendations

The MT25QL128ABA1EW7-0SIT TR is suitable as a substitute for the M25P80-VMP6TG TR based on the following factors:

• Both components maintain identical voltage supply specifications (2.7V ~ 3.6V) and operating temperature range (-40°C ~ 85°C), ensuring direct electrical compatibility
• Package footprint compatibility exists between 8-VDFN and 8-WDFN configurations, both measuring 6x5mm with exposed pad design
• Both components carry ROHS3 compliance and MSL 3 rating, meeting identical environmental and handling requirements
• The substitute part maintains active product status, ensuring long-term availability and supply chain continuity
• SPI - Quad I/O interface is backward compatible with standard SPI operation, allowing firmware to operate in legacy SPI mode if required

Frequently Asked Questions (FAQ)

Q: Can the MT25QL128ABA1EW7-0SIT TR directly replace the M25P80-VMP6TG TR on existing PCBs?

A: Yes. Both components use 8-pin VDFN/WDFN packages with 6x5mm footprints and exposed pad designs. Pin-to-pin compatibility is maintained for all signal and power connections.

Q: What is the difference between SPI and SPI - Quad I/O interfaces?

A: SPI - Quad I/O supports four data lines for parallel data transfer, enabling higher throughput. Standard SPI operation uses two data lines. The MT25QL128ABA1EW7-0SIT TR operates in standard SPI mode when configured accordingly, maintaining compatibility with existing firmware.

Q: Does the increased memory capacity (128Mbit vs 8Mbit) require firmware modifications?

A: Firmware modifications are not required for basic operation. The substitute part supports the same command set and addressing scheme. Applications utilizing the full 128Mbit capacity will require address space expansion in firmware.

Q: Are the voltage supply and temperature specifications identical?

A: Yes. Both components operate within 2.7V ~ 3.6V supply voltage and -40°C ~ 85°C temperature range, ensuring identical electrical operating conditions.

Q: What is the significance of the MSL 3 rating for both parts?

A: MSL 3 indicates both components require controlled moisture exposure for 168 hours maximum before soldering. Identical handling and storage protocols apply to both parts.