M2012SS1W01/CUL Toggle Switch SPDT Equivalent & Substitute Parts

Part Overview

The M2012SS1W01/CUL is an NKK Switches toggle switch with SPDT (Single Pole Double Throw) configuration, rated for 6A at 125V AC and 4A at 30V DC. This panel-mount switch features a standard round actuator with solder lug termination and epoxy sealed terminals. The product is classified as obsolete, making equivalent substitute parts necessary for ongoing applications and new designs requiring similar electrical and mechanical characteristics.

Key Parameters

Parameter	Value
Manufacturer Part Number	M2012SS1W01/CUL
Manufacturer	NKK Switches
Circuit Configuration	SPDT
Switch Function	On-On
Current Rating (AC)	6A
Current Rating (DC)	4A
Voltage Rating (AC)	125V
Voltage Rating (DC)	30V
Mounting Type	Panel Mount
Actuator Type	Standard Round
Actuator Length	10.50mm
Termination Style	Solder Lug
Panel Cutout Dimensions	Circular - 6.50mm Dia
Bushing Thread	1/4-40
Operating Temperature Range	-30°C to 85°C
Electrical Life	25,000 Cycles
RoHS Status	ROHS3 Compliant
Product Status	Obsolete

Substitute Part Grouping Explanation

Substitution eligibility is determined by the following critical parameters:

Electrical Compatibility Requirements:

Circuit configuration must be SPDT
Switch function must be On-On
Current rating must meet or exceed the application requirement (minimum 6A AC or 4A DC)
Voltage rating must meet or exceed the application requirement (minimum 125V AC or 30V DC)

Mechanical Compatibility Requirements:

Mounting type must be Panel Mount
Termination style must be Solder Lug
Panel cutout dimensions must accommodate the 6.50mm circular opening or smaller
Bushing thread must be 1/4-40
Operating temperature range must encompass -30°C to 85°C

Regulatory Compliance:

RoHS3 compliance preferred for new designs
REACH status consideration for supply chain continuity

Substitute parts are grouped into two categories based on electrical ratings:

Category A - Full Electrical Equivalents (6A/125V AC or higher): Parts meeting or exceeding the original 6A AC and 125V AC ratings with SPDT On-On configuration.

Category B - Reduced Rating Alternatives (5A/120V AC): Parts with slightly reduced current and voltage ratings (5A AC/DC at 120V AC) suitable for applications not requiring the full 6A/125V specification.

Category C - Low Voltage Alternatives (0.4VA/20V): Parts with significantly reduced ratings for low-voltage applications only.

Parameter Comparison

Part Number	Manufacturer	Circuit	Current (AC)	Current (DC)	Voltage (AC)	Voltage (DC)	Actuator Type	Actuator Length (mm)	Panel Cutout (mm)	Electrical Life (Cycles)	Product Status	RoHS Status
M2012SS1W01/CUL	NKK Switches	SPDT	6A	4A	125V	30V	Standard Round	10.50	6.50	25,000	Obsolete	ROHS3
100SP1T1B6M1QEH	E-Switch	SPDT	5A	5A	120V	28V	Standard Round	10.41	6.35	40,000	Active	ROHS3
100SP1T6B11M1QEH	E-Switch	SPDT	5A	5A	120V	28V	Flat Anti-Rotation	12.30	6.35	40,000	Active	ROHS3
100SP1T6B11M1REH	E-Switch	SPDT	0.4VA	0.4VA	20V	20V	Flat Anti-Rotation	12.30	6.35	40,000	Active	ROHS3
34ASP11B5M1QT	Grayhill Inc.	SPDT	5A	5A	125V	28V	Standard Round	10.41	6.35	40,000	Active	RoHS Compliant
7101L40HZQE	C&K	SPDT	5A	5A	120V	28V	Lever for Cap	—	6.35	100,000	Active	ROHS3
7101L41HZQE2	C&K	SPDT	5A	5A	120V	28V	Flat Anti-Rotation	13.49	6.35	100,000	Active	ROHS3
7101MPY1ZGE	C&K	SPDT	5A	5A	120V	28V	Anti-Rotation	5.08	6.35	100,000	Active	ROHS3
7101MPY1ZQE	C&K	SPDT	5A	5A	120V	28V	Anti-Rotation	5.08	6.35	100,000	Active	ROHS3
7101MY4ZBE	C&K	SPDT	0.4VA	0.4VA	20V	20V	Standard Round	5.08	6.35	100,000	Active	RoHS non-compliant
7101MY4ZQE	C&K	SPDT	5A	5A	120V	28V	Standard Round	5.08	6.35	100,000	Active	ROHS3

Engineering Selection Recommendations

Primary Substitutes for Full Electrical Equivalence:

The 34ASP11B5M1QT from Grayhill Inc. provides the closest electrical match with 5A AC/DC at 125V AC, meeting the original voltage specification. This part is active in production with ROHS3 compliance and 40,000 cycle electrical life, providing improved reliability over the obsolete M2012SS1W01/CUL.

Secondary Substitutes for Reduced Rating Applications:

When application requirements permit operation at 120V AC and 5A AC/DC, the following active parts are suitable:

100SP1T1B6M1QEH (E-Switch) with standard round actuator and 40,000 cycle life
7101MPY1ZGE or 7101MPY1ZQE (C&K) with compact 5.08mm actuator and extended 100,000 cycle life
7101MY4ZQE (C&K) with standard round actuator and 100,000 cycle life

Low-Voltage Applications Only:

The 100SP1T6B11M1REH and 7101MY4ZBE are restricted to applications operating at 20V or below due to their 0.4VA rating and are not suitable for the original 125V/6A specification.

Compliance Considerations:

All recommended primary and secondary substitutes maintain ROHS3 compliance except 7101MY4ZBE, which is RoHS non-compliant. For new designs, prioritize ROHS3-compliant alternatives to ensure regulatory alignment.

Mechanical Fit Verification:

Panel cutout dimensions for substitute parts are 6.35mm, which is smaller than the original 6.50mm. Verify that existing panel openings can accommodate this dimension or require modification. Actuator length variations (5.08mm to 13.49mm) must be evaluated against available panel depth and user interface requirements.

Frequently Asked Questions (FAQ)

Q: Can I use a 5A rated switch to replace the 6A M2012SS1W01/CUL?

A: Substitution is application-dependent. If your circuit operates at or below 5A, a 5A-rated switch is acceptable. If your application requires the full 6A capacity, only the 34ASP11B5M1QT at 125V AC provides equivalent current handling. Verify actual circuit current draw before substitution.

Q: What is the difference between 120V and 125V rated switches?

A: The M2012SS1W01/CUL is rated for 125V AC, while most substitutes are rated for 120V AC. Both ratings are within standard North American utility voltage tolerance (120V ±10%). For applications requiring the full 125V specification, use the 34ASP11B5M1QT.

Q: Are the panel cutout dimensions compatible?

A: The original part requires a 6.50mm circular opening. Most substitutes use 6.35mm openings, which are smaller and fit within the original opening. However, verify that your panel drilling or existing opening can accommodate the substitute dimension. No modification is required if the opening is 6.50mm or larger.

Q: What does "electrical life" mean, and why does it vary?

A: Electrical life is the number of on-off cycles a switch can perform before failure. The M2012SS1W01/CUL is rated for 25,000 cycles, while most substitutes offer 40,000 to 100,000 cycles. Higher cycle ratings indicate longer operational life and improved reliability for frequent switching applications.

Q: Can I use a switch with a different actuator type?

A: Actuator type affects user interface and mechanical fit. The original uses a standard round actuator. Substitutes with flat anti-rotation or lever actuators provide different tactile feedback and may require different panel cutout shapes. Verify mechanical compatibility with your panel design and user requirements before substitution.

Q: Why are some parts listed as "Active" and others as "Obsolete"?

A: Active parts are currently manufactured and available from distributors. The M2012SS1W01/CUL is obsolete, meaning NKK Switches no longer manufactures it. Active substitutes ensure long-term supply chain availability and support for future production runs.

Q: Are low-voltage parts (0.4VA/20V) suitable for my application?

A: Low-voltage parts are only suitable for applications operating at 20V or below. They cannot be used as substitutes for the 125V/6A specification. Use these parts only if your application is specifically designed for low-voltage operation.

Q: What is ROHS3 compliance, and why does it matter?

A: ROHS3 (Restriction of Hazardous Substances Directive 3) compliance indicates the part meets European environmental regulations restricting lead, mercury, cadmium, and other hazardous materials. For new designs and applications subject to environmental regulations, ROHS3-compliant parts are required. The M2012SS1W01/CUL is ROHS3 compliant, as are most recommended substitutes.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message