LLMGA201208T221RG Ferrite Bead Equivalent & Substitute Parts

Part Overview

The LLMGA201208T221RG is a 120 Ohm ferrite bead manufactured by Taiyo Yuden, designed for power line filtering applications in 0805 (2012 Metric) surface mount packages. This component operates at 100 MHz impedance with a maximum current rating of 2.5A and DC resistance of 32 mOhm. The part is classified as Active product status and is ROHS3 compliant.

Equivalent and substitute parts are necessary when the primary part becomes unavailable, when alternative manufacturers are required for supply chain diversification, or when design requirements permit enhanced electrical characteristics such as higher current ratings or lower DC resistance.

Key Parameters

Parameter	Value
Impedance @ Frequency	120 Ohms @ 100 MHz
Current Rating (Max)	2.5A
DC Resistance (DCR) (Max)	32 mOhm
Package / Case	0805 (2012 Metric)
Mounting Type	Surface Mount
Operating Temperature Range	-40°C ~ 125°C
Number of Lines	1
RoHS Status	ROHS3 Compliant
Moisture Sensitivity Level (MSL)	1 (Unlimited)

Substitute Part Grouping Explanation

Substitution of ferrite beads is determined by the following critical parameters:

Primary Substitution Criteria:

Impedance @ 100 MHz (120 Ohms or 100 Ohms)
Package / Case (0805 / 2012 Metric)
Mounting Type (Surface Mount)
Number of Lines (1)

Secondary Compatibility Factors:

Current Rating (Max): Substitute parts with equal or higher ratings are acceptable
DC Resistance (DCR): Substitute parts with equal or lower resistance are acceptable
Operating Temperature Range: Substitute parts must cover the application temperature requirements
RoHS Compliance: All substitutes maintain ROHS3 compliance

Substitute parts are grouped into two categories based on impedance specification:

Category A - 120 Ohm Impedance @ 100 MHz: Direct electrical equivalents with identical impedance specification. These parts are fully interchangeable from an impedance perspective.

Category B - 100 Ohm Impedance @ 100 MHz: Parts with 100 Ohm impedance specification. These represent close impedance alternatives where application tolerance permits minor impedance deviation.

Parameter Comparison

Manufacturer Part Number	Manufacturer	Impedance @ 100 MHz	Current Rating (Max)	DCR (Max)	Operating Temperature	Product Status	Filter Type
LLMGA201208T221RG	Taiyo Yuden	120 Ohms	2.5A	32 mOhm	-40°C ~ 125°C	Active	Power Line
FBMH2012HM121-T	Taiyo Yuden	120 Ohms	2.5A	32 mOhm	-40°C ~ 125°C	Not For New Designs	Power Line
LSMGA201208T121RG	Taiyo Yuden	120 Ohms	2.5A	32 mOhm	-40°C ~ 125°C	Active	Power Line
742792023	Würth Elektronik	120 Ohms	3A	30 mOhm	-55°C ~ 125°C	Active	Signal Line
BBUP00201209101Y00	Pulse Electronics	100 Ohms	5A	20 mOhm	-55°C ~ 125°C	Active	Not Specified
BBUP00201209121Y00	Pulse Electronics	120 Ohms	5A	20 mOhm	-55°C ~ 125°C	Active	Not Specified
BLM21PG121SN1D	Murata Electronics	120 Ohms	3A	30 mOhm	-55°C ~ 125°C	Active	Power Line
FBU201209T-121Y-S-H	Cal-Chip Electronics, Inc.	120 Ohms	5A	15 mOhm	-55°C ~ 125°C	Active	Power Line
HI0805O121R-10	Laird-Signal Integrity Products	120 Ohms	3.5A	20 mOhm	-40°C ~ 125°C	Active	Power, Signal Line
ILHB0805ER121V	Vishay Dale	120 Ohms	5A	20 mOhm	-55°C ~ 125°C	Active	Not Specified
MPZ2012S101AT000	TDK Corporation	100 Ohms	4A	20 mOhm	-55°C ~ 125°C	Active	Power Line

Engineering Selection Recommendations

Primary Substitutes (120 Ohm Impedance, Active Status):

LSMGA201208T121RG (Taiyo Yuden, LSMG Series) is the recommended primary substitute. This part maintains identical electrical specifications to the LLMGA201208T221RG with 120 Ohms impedance, 2.5A current rating, and 32 mOhm DCR. Both parts are manufactured by Taiyo Yuden and are Active product status, ensuring long-term availability and supply chain continuity.

BBUP00201209121Y00 (Pulse Electronics, BBUP Series) provides enhanced electrical performance with 120 Ohms impedance, 5A current rating, and 20 mOhm DCR. This part is suitable for applications requiring higher current capacity or lower DC resistance while maintaining the same impedance specification.

FBU201209T-121Y-S-H (Cal-Chip Electronics, FBU Series) offers superior electrical characteristics with 120 Ohms impedance, 5A current rating, and 15 mOhm DCR. This part provides the lowest DC resistance among 120 Ohm substitutes and is Active product status.

Secondary Substitutes (120 Ohm Impedance, Enhanced Temperature Range):

BLM21PG121SN1D (Murata Electronics, EMIFIL BLM21 Series) provides 120 Ohms impedance with extended operating temperature range (-55°C ~ 125°C), 3A current rating, and 30 mOhm DCR. This part is suitable for applications requiring wider temperature operation.

HI0805O121R-10 (Laird-Signal Integrity Products, 0805 Series) maintains 120 Ohms impedance with 3.5A current rating and 20 mOhm DCR. This part supports both power and signal line applications.

ILHB0805ER121V (Vishay Dale, ILHB Series) provides 120 Ohms impedance with 5A current rating and 20 mOhm DCR, offering enhanced current capacity.

Alternative Impedance Substitutes (100 Ohm Impedance):

BBUP00201209101Y00 (Pulse Electronics, BBUP Series) and MPZ2012S101AT000 (TDK Corporation, MPZ Series) provide 100 Ohms impedance at 100 MHz. These parts are suitable only when application design permits 100 Ohm impedance operation and represents a 16.7% impedance reduction from the primary specification.

Discontinued or Restricted Status:

FBMH2012HM121-T (Taiyo Yuden, FB Series) is classified as Not For New Designs and should not be selected for new applications despite identical electrical specifications to the primary part.

742792023 (Würth Elektronik, WE-CBF Series) is classified as Signal Line filter type rather than Power Line, and should be selected only when signal line filtering is the application requirement.

Frequently Asked Questions (FAQ)

Q: Can LSMGA201208T121RG be used as a direct replacement for LLMGA201208T221RG?

A: Yes. Both parts are manufactured by Taiyo Yuden, maintain identical impedance (120 Ohms @ 100 MHz), current rating (2.5A), DC resistance (32 mOhm), and operating temperature range (-40°C ~ 125°C). Both are Active product status. The parts are electrically and mechanically interchangeable.

Q: What is the difference between BBUP00201209121Y00 and LLMGA201208T221RG?

A: Both parts maintain 120 Ohms impedance at 100 MHz and 0805 package. BBUP00201209121Y00 provides higher current rating (5A versus 2.5A) and lower DC resistance (20 mOhm versus 32 mOhm). BBUP00201209121Y00 also supports extended operating temperature (-55°C ~ 125°C versus -40°C ~ 125°C). These enhancements make BBUP00201209121Y00 suitable for applications requiring higher current capacity or lower power dissipation.

Q: Can 100 Ohm ferrite beads substitute for 120 Ohm beads?

A: 100 Ohm ferrite beads (BBUP00201209101Y00 or MPZ2012S101AT000) represent a 16.7% impedance reduction from the 120 Ohm specification. Substitution is permissible only when application design tolerances explicitly permit 100 Ohm impedance operation. Impedance mismatch may affect filtering performance and should be evaluated against specific application requirements.

Q: Why is FBMH2012HM121-T listed as Not For New Designs?

A: FBMH2012HM121-T is classified as Not For New Designs by the manufacturer, indicating the part is in end-of-life status. While electrically equivalent to LLMGA201208T221RG, this part should not be selected for new product designs due to potential future availability constraints. Active status alternatives such as LSMGA201208T121RG are recommended.

Q: What is the significance of Filter Type designation (Power Line versus Signal Line)?

A: Filter Type indicates the primary application classification. Power Line ferrite beads are optimized for power supply filtering, while Signal Line beads are optimized for signal integrity. Parts designated as Power, Signal Line support both applications. Filter Type does not restrict substitution but indicates the manufacturer's primary design intent.

Q: Are all substitute parts ROHS3 compliant?

A: Yes. All substitute parts listed maintain ROHS3 compliance, consistent with the primary part LLMGA201208T221RG. All parts are suitable for applications requiring RoHS compliance.

Q: What is Moisture Sensitivity Level (MSL) and why is it important?

A: MSL indicates the component's sensitivity to moisture absorption during storage and handling. MSL 1 (Unlimited) indicates the component has no moisture sensitivity restrictions and does not require special dry-pack storage or baking procedures prior to reflow soldering. All listed parts maintain MSL 1 classification.

Q: Can FBU201209T-121Y-S-H be used in all applications where LLMGA201208T221RG is specified?

A: FBU201209T-121Y-S-H maintains 120 Ohms impedance and 0805 package compatibility. However, it provides enhanced specifications: 5A current rating (versus 2.5A), 15 mOhm DCR (versus 32 mOhm), and extended temperature range (-55°C ~ 125°C versus -40°C ~ 125°C). These enhancements make FBU201209T-121Y-S-H suitable for applications requiring higher current capacity or lower power dissipation. Verification of PCB layout and thermal design is recommended when upgrading to lower DCR components.

Q: What is the difference between Cut Tape (CT) and Tape & Reel (TR) packaging?

A: Tape & Reel (TR) packaging provides components on continuous tape suitable for automated pick-and-place assembly equipment. Cut Tape (CT) provides components on tape segments suitable for manual assembly or lower-volume production. Both packaging formats contain identical components; packaging selection depends on assembly process requirements and production volume.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message