KBL601G Bridge Rectifier Equivalent & Substitute Parts

Part Overview

The KBL601G is a single-phase bridge rectifier manufactured by GeneSiC Semiconductor, rated for 50 V peak reverse voltage and 6 A average rectified current. This component is classified as Active product status and is RoHS Compliant with Moisture Sensitivity Level 1 (Unlimited). The KBL601G is supplied in bulk packaging with a 4-SIP, KBL package configuration suitable for through-hole mounting applications.

Substitute parts are necessary when the KBL601G becomes unavailable, when alternative packaging formats are required, or when design specifications allow for components with equivalent or superior electrical ratings within the same functional category.

Key Parameters

Parameter	Value
Diode Type	Single Phase
Technology	Standard
Voltage - Peak Reverse (Max)	50 V
Current - Average Rectified (Io)	6 A
Voltage - Forward (Vf) (Max) @ If	1.1 V @ 6 A
Current - Reverse Leakage @ Vr	5 µA @ 50 V
Operating Temperature Range	-55°C ~ 150°C (TJ)
Mounting Type	Through Hole
Package / Case	4-SIP, KBL
RoHS Status	RoHS Compliant
Moisture Sensitivity Level (MSL)	1 (Unlimited)

Substitute Part Grouping Explanation

Substitution logic for the KBL601G is based on the following critical parameters:

Primary Substitution Criteria:

Diode Type: Single Phase (required match)
Technology: Standard (required match)
Voltage - Peak Reverse (Max): 50 V (required match or higher rating acceptable)
Mounting Type: Through Hole (required match)
Operating Temperature Range: -55°C ~ 150°C minimum (required match or wider range acceptable)

Current Rating Consideration: The KBL601G is rated for 6 A average rectified current. Substitute parts with equal or higher current ratings (6 A, 8 A, or 10 A) are functionally compatible. Parts with lower current ratings (3 A, 4 A) are not suitable substitutes as they cannot handle the specified load.

Forward Voltage Consideration: Forward voltage specifications vary across manufacturers. The KBL601G specifies 1.1 V @ 6 A. Substitute parts with forward voltage ratings of 1.0 V or 1.1 V at comparable or higher current test points are acceptable.

Packaging Consideration: The KBL601G uses 4-SIP, KBL package configuration. Substitute parts may use alternative through-hole packages (4-ESIP, GBU) provided mechanical fit and pin compatibility are verified for the target application.

Parameter Comparison

Part Number	Manufacturer	Voltage - Peak Reverse (Max)	Current - Average Rectified (Io)	Voltage - Forward (Vf) (Max) @ If	Current - Reverse Leakage @ Vr	Operating Temperature	Package / Case	Product Status	RoHS Status
KBL601G	GeneSiC Semiconductor	50 V	6 A	1.1 V @ 6 A	5 µA @ 50 V	-55°C ~ 150°C	4-SIP, KBL	Active	RoHS Compliant
GBU10005	SMC Diode Solutions	50 V	10 A	1.1 V @ 10 A	5 µA @ 50 V	-55°C ~ 150°C	4-ESIP	Active	ROHS3 Compliant
GBU10005-G	Comchip Technology	50 V	10 A	1 V @ 5 A	10 µA @ 50 V	-55°C ~ 150°C	4-SIP, GBU	Active	ROHS3 Compliant
GBU6005	SMC Diode Solutions	50 V	6 A	1.1 V @ 6 A	5 µA @ 50 V	-55°C ~ 150°C	4-ESIP	Active	ROHS3 Compliant
GBU6A-BP	Micro Commercial Co	50 V	6 A	1 V @ 3 A	5 µA @ 50 V	-55°C ~ 150°C	4-SIP, GBU	Not For New Designs	ROHS3 Compliant
GBU8005	SMC Diode Solutions	50 V	8 A	1.1 V @ 8 A	5 µA @ 50 V	-55°C ~ 150°C	4-ESIP	Active	ROHS3 Compliant
GBU8A	Fairchild Semiconductor	50 V	5.6 A	1 V @ 8 A	5 µA @ 50 V	-50°C ~ 150°C	4-ESIP, GBU	Active	Not Specified
GBU8A-BP	Micro Commercial Co	50 V	8 A	1 V @ 4 A	5 µA @ 50 V	-55°C ~ 150°C	4-SIP, GBU	Not For New Designs	ROHS3 Compliant
GBU4005	SMC Diode Solutions	50 V	4 A	1.1 V @ 4 A	5 µA @ 50 V	-55°C ~ 150°C	4-ESIP	Active	ROHS3 Compliant
GBU4A	Good-Ark Semiconductor	50 V	3 A	1 V @ 2 A	5 µA @ 50 V	-55°C ~ 150°C	4-SIP, GBU	Active	ROHS3 Compliant
GBU4A-BP	Micro Commercial Co	50 V	4 A	1 V @ 2 A	5 µA @ 50 V	-55°C ~ 150°C	4-SIP, GBU	Not For New Designs	ROHS3 Compliant

Engineering Selection Recommendations

Recommended Primary Substitutes (Active Status, Current Rating ≥ 6 A):

GBU6005 (SMC Diode Solutions) is the most direct substitute. It matches the KBL601G in voltage rating (50 V), current rating (6 A), forward voltage specification (1.1 V @ 6 A), and reverse leakage (5 µA @ 50 V). Both components are Active status and RoHS compliant. The primary difference is packaging format (4-ESIP versus 4-SIP, KBL), which requires mechanical verification for board-level compatibility.

GBU8005 (SMC Diode Solutions) and GBU10005 (SMC Diode Solutions) are acceptable substitutes with higher current ratings (8 A and 10 A respectively). Both maintain 50 V voltage rating, -55°C to 150°C operating range, and Active product status. These parts provide design margin for applications where current demand may exceed 6 A nominal specification.

Secondary Substitutes (Active Status, Current Rating < 6 A):

GBU4005 (SMC Diode Solutions) is rated for 4 A average rectified current. This part is not suitable as a direct substitute for the KBL601G in applications requiring 6 A continuous operation. Use only when application current requirements are confirmed below 4 A.

Not Recommended for New Designs:

GBU6A-BP, GBU8A-BP, and GBU4A-BP are marked "Not For New Designs" by Micro Commercial Co. These parts should not be selected for new circuit designs, though they may be acceptable for legacy system maintenance where existing inventory exists.

Compliance Considerations:

All recommended substitutes maintain RoHS3 compliance or equivalent environmental standards. The KBL601G is RoHS Compliant; substitute parts are ROHS3 Compliant, which represents an updated compliance standard. Moisture Sensitivity Level 1 (Unlimited) is consistent across all recommended substitutes, indicating no special handling requirements during storage or assembly.

Frequently Asked Questions (FAQ)

Q: Can GBU4005 replace KBL601G in my application?

A: GBU4005 is rated for 4 A average rectified current, while KBL601G is rated for 6 A. GBU4005 is not a suitable substitute if your application requires 6 A continuous operation. Use GBU4005 only if your actual circuit current demand is confirmed below 4 A maximum.

Q: What is the difference between GBU6005 and GBU6A-BP?

A: Both parts are rated for 50 V and 6 A. GBU6005 (SMC Diode Solutions) is Active status and recommended for new designs. GBU6A-BP (Micro Commercial Co) is marked "Not For New Designs" and should not be used in new circuit development. For new applications, select GBU6005.

Q: Can I use GBU10005 instead of KBL601G?

A: Yes. GBU10005 is rated for 10 A average rectified current, which exceeds the KBL601G 6 A requirement. Both parts share 50 V voltage rating, -55°C to 150°C operating temperature, and equivalent reverse leakage characteristics. GBU10005 provides additional current capacity margin. Verify mechanical package compatibility (4-ESIP versus 4-SIP, KBL) for your PCB layout.

Q: What does "Not For New Designs" mean?

A: Parts marked "Not For New Designs" are legacy components that manufacturers no longer recommend for new circuit development. These parts may have limited availability, extended lead times, or planned discontinuation. For new applications, select parts with Active status such as GBU6005, GBU8005, or GBU10005.

Q: Are all substitute parts RoHS compliant?

A: The KBL601G is RoHS Compliant. All recommended substitute parts are ROHS3 Compliant, which is an updated compliance standard. Both standards meet environmental and hazardous substance restrictions. ROHS3 represents current regulatory requirements and is acceptable for new designs.

Q: Does package type affect electrical performance?

A: Package type (4-SIP, KBL versus 4-ESIP, GBU) does not affect electrical performance. Both are through-hole configurations with equivalent electrical characteristics. Package selection is determined by PCB layout, board space constraints, and mechanical mounting requirements. Verify pin spacing and hole diameter compatibility with your PCB design before substitution.

Q: What is the significance of forward voltage (Vf) differences?

A: Forward voltage varies slightly across manufacturers and test conditions. KBL601G specifies 1.1 V @ 6 A; GBU6005 also specifies 1.1 V @ 6 A (direct match). GBU10005-G specifies 1 V @ 5 A, which is measured at different current. These variations are within normal manufacturing tolerance and do not affect functional compatibility in standard rectifier applications.

Q: Can I substitute a higher-rated part (8 A or 10 A) for a 6 A requirement?

A: Yes. Higher current-rated parts (GBU8005 at 8 A, GBU10005 at 10 A) are acceptable substitutes for 6 A applications. The higher rating provides design margin and does not degrade performance. The circuit will operate at the same voltage and current levels as the original 6 A part; the higher rating simply indicates the component can handle greater load if needed in future design revisions.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message