KAI-08051-AXA-JD-BA Equivalent & Substitute Parts

Part Overview

The KAI-08051-AXA-JD-BA is an interline CCD image sensor manufactured by onsemi, featuring a 3296H x 2472V pixel array with 5.5µm x 5.5µm pixel size. This component operates at 16 frames per second and requires a 14.5V to 15.5V supply voltage. The part is classified as obsolete, necessitating identification of functionally equivalent alternatives for ongoing system design and maintenance applications.

Substiute Parts

KAI-08051-AXA-JD-BA

onsemiIn Stock: 951KAI-08051-AXA-JD-BA Datasheet

Current PartRFQ

NOIX1SN8000B-LTI

onsemiIn Stock: 1132NOIX1SN8000B-LTI Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution of the KAI-08051-AXA-JD-BA is determined by the following critical parameters:

• Sensor Type: CCD technology with interline architecture
• Resolution: 3296H x 2472V active pixel array
• Pixel Geometry: 5.5µm x 5.5µm pixel dimensions
• Frame Rate: 16 frames per second capability
• Supply Voltage: 14.5V to 15.5V operating range
• Package Configuration: 68-pin BPGA form factor
• Compliance: ROHS3 compliance and REACH unaffected status

The identified substitute NOIX1SN8000B-LTI represents a technology transition from CCD to CMOS architecture. While this substitute maintains onsemi manufacturer origin and ROHS3 compliance, it introduces significant differences in sensor type, pixel array dimensions, pixel size, frame rate capability, and supply voltage requirements.

Parameter Comparison

Engineering Selection Recommendations

The KAI-08051-AXA-JD-BA is classified as obsolete. The NOIX1SN8000B-LTI is an active product from the same manufacturer, maintaining ROHS3 compliance and REACH unaffected status.

Selection of NOIX1SN8000B-LTI as a substitute requires system-level evaluation of the following differences:

• Sensor architecture transition from CCD to CMOS technology
• Pixel array dimensions: 4096H x 2160V versus 3296H x 2472V
• Pixel size reduction from 5.5µm to 3.2µm
• Frame rate increase from 16 fps to 128 fps
• Supply voltage reduction from 14.5V–15.5V to 1.7V–1.9V and 2.7V–2.9V
• Operating temperature range expansion from -50°C to -40°C minimum

These parameter differences necessitate circuit redesign, firmware modification, and optical system recalibration.

Frequently Asked Questions (FAQ)

Q: Can NOIX1SN8000B-LTI directly replace KAI-08051-AXA-JD-BA without circuit modification?

A: No. The substitute part differs in sensor type (CMOS vs. CCD), supply voltage requirements, pixel array dimensions, pixel size, and frame rate. Direct substitution without circuit redesign is not feasible.

Q: What are the primary differences between these two sensors?

A: The main differences are sensor architecture (CCD interline versus CMOS), active pixel array (3296H x 2472V versus 4096H x 2160V), pixel dimensions (5.5µm versus 3.2µm), frame rate capability (16 fps versus 128 fps), and supply voltage (14.5V–15.5V versus 1.7V–1.9V and 2.7V–2.9V).

Q: Are both parts compliant with environmental regulations?

A: Yes. Both KAI-08051-AXA-JD-BA and NOIX1SN8000B-LTI are ROHS3 compliant and REACH unaffected.

Q: What is the package difference between these sensors?

A: KAI-08051-AXA-JD-BA uses a 68-pin BPGA package (40x29mm). NOIX1SN8000B-LTI uses a 163-pin BCLGA package (20.88x19.9mm).

Q: Which part has a wider operating temperature range?

A: NOIX1SN8000B-LTI operates from -40°C to 85°C (junction temperature), while KAI-08051-AXA-JD-BA operates from -50°C to 70°C (ambient temperature). The temperature measurement references differ between the two specifications.