JBXFD1G06MWSDSR Equivalent & Substitute Parts

Part Overview

The JBXFD1G06MWSDSR is a 6-position circular connector plug manufactured by Souriau-Sunbank by Eaton, featuring male pins with gold-plated mating contacts. This connector is designed for industrial, instrumentation, medical, and telecommunications applications requiring reliable push-pull fastening and shielded signal transmission. The part maintains Active product status with 825 units in current inventory. Equivalent and substitute parts are identified to support procurement flexibility, design alternatives, and supply chain continuity for applications where the primary part may be unavailable or where specific termination or orientation requirements necessitate alternative configurations.

Substiute Parts

JBXFD1G06MWSDSR

Souriau-Sunbank by EatonIn Stock: 877JBXFD1G06MWSDSR Datasheet

Current PartRFQ

FFA.1S.306.CLAC62

LEMOIn Stock: 788FFA.1S.306.CLAC62 Datasheet

SimilarRFQ

FGG.1B.306.CLAD42

PEI-GenesisIn Stock: 988FGG.1B.306.CLAD42 Datasheet

SimilarRFQ

FGG.1B.306.CLAD52Z

PEI-GenesisIn Stock: 1005FGG.1B.306.CLAD52Z Datasheet

SimilarRFQ

FGG.1B.306.CLAD72

LEMOIn Stock: 1134FGG.1B.306.CLAD72 Datasheet

SimilarRFQ

FGG.1B.306.CLAZ

PEI-GenesisIn Stock: 1195FGG.1B.306.CLAZ Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the JBXFD1G06MWSDSR is determined by the following critical parameters: 6-position configuration, push-pull fastening mechanism, shielded design, gold-plated mating contacts, brass shell material with PEEK insert, and compliance with ROHS3 and REACH regulations. The substitute parts listed maintain these core electrical and mechanical characteristics while differing in specific attributes such as termination method (solder cup versus push-pull), shell finish specification, operating temperature range, and ingress protection rating. All substitute parts are classified as circular connectors within the same functional category and support equivalent signal transmission and mechanical interface requirements.

Parameter Comparison

Engineering Selection Recommendations

Selection of substitute parts for the JBXFD1G06MWSDSR must prioritize compliance status and core electrical specifications. FFA.1S.306.CLAC62 and FGG.1B.306.CLAD72 are fully documented alternatives with confirmed ROHS3 compliance and REACH unaffected status, matching the primary part's regulatory requirements. Both alternatives maintain 7A current rating and gold-plated mating contacts. FFA.1S.306.CLAC62 differs in connector type (female sockets and male pins) and termination method (solder cup), suitable for applications requiring wire termination rather than push-pull mating. FGG.1B.306.CLAD72 maintains male pin configuration with solder cup termination and extended operating temperature range (-55°C ~ 250°C), appropriate for applications exceeding the primary part's thermal limits. FGG.1B.306.CLAD42, FGG.1B.306.CLAD52Z, and FGG.1B.306.CLAZ are listed as alternatives but contain incomplete technical documentation; selection of these parts requires confirmation of electrical ratings and compliance certifications from the manufacturer.

Frequently Asked Questions (FAQ)

Q: What determines whether a part can substitute for the JBXFD1G06MWSDSR?

A: Substitution is based on matching the 6-position configuration, push-pull fastening mechanism, shielded design, gold-plated mating contacts, brass shell with PEEK insert, and regulatory compliance (ROHS3 Compliant, REACH Unaffected). Variations in termination method, operating temperature range, and ingress protection rating are acceptable when application requirements permit.

Q: Can FFA.1S.306.CLAC62 replace the JBXFD1G06MWSDSR in all applications?

A: FFA.1S.306.CLAC62 is functionally equivalent for 6-position shielded signal transmission with identical current rating and gold contact finish. However, it features female sockets and male pins with solder cup termination, whereas the primary part uses male pins with push-pull mating. Selection depends on whether the application requires solder cup wire termination or push-pull connector mating.

Q: What is the difference between FGG.1B.306.CLAD72 and the primary part?

A: FGG.1B.306.CLAD72 maintains male pin configuration, 7A current rating, and gold-plated contacts identical to JBXFD1G06MWSDSR. Primary differences are solder cup termination (versus unspecified termination on primary part) and extended operating temperature range (-55°C ~ 250°C versus -40°C ~ 125°C). This substitute is suitable for applications requiring higher thermal performance.

Q: Are FGG.1B.306.CLAD42, FGG.1B.306.CLAD52Z, and FGG.1B.306.CLAZ suitable direct replacements?

A: These parts are listed as alternatives within the same connector category with 6-position configuration and push-pull fastening. However, incomplete technical documentation prevents confirmation of electrical ratings, contact finish specifications, and regulatory compliance. Direct substitution requires manufacturer verification of current rating, voltage rating, and compliance certifications.

Q: What packaging considerations apply to these substitute parts?

A: The primary part JBXFD1G06MWSDSR is supplied in unspecified packaging. All listed substitutes are available in Bulk packaging, suitable for production assembly and procurement workflows. Packaging format does not affect electrical or mechanical compatibility.

Q: Can these substitutes be used interchangeably in the same connector interface?

A: Mechanical and electrical interchangeability depends on specific application requirements. FFA.1S.306.CLAC62 features different contact configuration (female sockets and male pins). FGG.1B.306.CLAD72 maintains identical male pin configuration. All alternatives maintain 6-position, push-pull, shielded design. Physical interface compatibility must be confirmed against mating connector specifications.