IXKP13N60C5M N-Channel 600V 6.5A MOSFET Equivalent & Substitute Parts

Part Overview

The IXKP13N60C5M is an N-Channel 600V 6.5A MOSFET manufactured by IXYS in the CoolMOS™ series, housed in a TO-220ABFP through-hole package. This device is classified as obsolete product status. Due to its obsolescence, equivalent and substitute parts from active manufacturers are necessary to maintain design continuity and ensure long-term component availability for new production runs and field replacements.

Key Parameters

Parameter	Value	Unit
FET Type	N-Channel	—
Drain to Source Voltage (Vdss)	600	V
Continuous Drain Current (Id) @ 25°C	6.5	A
Drive Voltage (Max Rds On)	10	V
Rds On (Max) @ Id, Vgs	300 mOhm @ 6.6A, 10V	—
Gate Charge (Qg) (Max) @ Vgs	30	nC @ 10V
Vgs (Max)	±20	V
Input Capacitance (Ciss) (Max) @ Vds	1100	pF @ 100V
Operating Temperature Range	-55 to 150	°C (TJ)
Mounting Type	Through Hole	—
Package / Case	TO-220-3 Full Pack	—
RoHS Status	ROHS3 Compliant	—
Moisture Sensitivity Level (MSL)	1 (Unlimited)	—

Substitute Part Grouping Explanation

Substitution of the IXKP13N60C5M is determined by the following critical electrical and mechanical parameters:

Primary Substitution Criteria:

Drain to Source Voltage (Vdss): 600V minimum
Continuous Drain Current (Id): Equal to or greater than 6.5A
Drive Voltage: 10V gate drive compatibility
Rds On (Max): Equal to or lower than 300 mOhm at specified conditions
Gate Charge (Qg): Lower or comparable values preferred for switching performance
Vgs (Max): ±20V or higher gate voltage rating
Mounting Type: Through Hole
Package: TO-220-3 Full Pack compatible footprint

Substitution Logic: Parts are grouped into two categories based on their electrical performance relative to the main part:

Direct Equivalents – Parts with 600V Vdss, 6.5A to 11A Id range, and comparable Rds On characteristics. These parts maintain electrical performance within the original design envelope.
Higher Performance Substitutes – Parts with 600V Vdss but higher current ratings (13A to 17A) or parts with higher voltage ratings (650V to 800V). These parts provide enhanced capability and are suitable when design margins permit.

All substitute parts maintain TO-220-3 package compatibility, RoHS3 compliance, and through-hole mounting configuration.

Parameter Comparison

Part Number	Manufacturer	Vdss (V)	Id @ 25°C (A)	Rds On Max (mOhm)	Qg Max (nC)	Vgs Max (V)	Ciss Max (pF)	Product Status	Package
IXKP13N60C5M	IXYS	600	6.5	300 @ 6.6A, 10V	30 @ 10V	±20	1100 @ 100V	Obsolete	TO-220ABFP
STF13N60M2	STMicroelectronics	600	11	380 @ 5.5A, 10V	17 @ 10V	±25	580 @ 100V	Active	TO-220FP
STF13NM60ND	STMicroelectronics	600	11	380 @ 5.5A, 10V	24.5 @ 10V	±25	845 @ 50V	Active	TO-220FP
STF15N60M2-EP	STMicroelectronics	600	11	378 @ 5.5A, 10V	17 @ 10V	±25	590 @ 100V	Active	TO-220FP
R6015ENX	Rohm Semiconductor	600	15	290 @ 6.5A, 10V	40 @ 10V	±20	910 @ 25V	Active	TO-220FM
STF18N60M2	STMicroelectronics	600	13	280 @ 6.5A, 10V	21.5 @ 10V	±25	791 @ 100V	Active	TO-220FP
STF18NM60N	STMicroelectronics	600	13	285 @ 6.5A, 10V	35 @ 10V	±25	1000 @ 50V	Active	TO-220FP
SPA11N65C3XKSA1	Infineon Technologies	650	11	380 @ 7A, 10V	60 @ 10V	±20	1200 @ 25V	Not For New Designs	PG-TO220-3-31
FDPF17N60NT	onsemi	600	17	340 @ 8.5A, 10V	65 @ 10V	±30	3040 @ 25V	Active	TO-220F-3
STF17N80K5	STMicroelectronics	800	14	340 @ 7A, 10V	26 @ 10V	±30	866 @ 100V	Active	TO-220FP
STF18NM80	STMicroelectronics	800	17	295 @ 8.5A, 10V	70 @ 10V	±30	2070 @ 50V	Active	TO-220FP

Engineering Selection Recommendations

For Direct Replacement in Existing Designs:

The STF13N60M2, STF13NM60ND, and STF15N60M2-EP from STMicroelectronics are recommended as primary substitutes. These parts maintain 600V Vdss rating, provide 11A continuous drain current (exceeding the 6.5A requirement), and are classified as Active product status. All three parts are RoHS3 compliant with MSL 1 (Unlimited) moisture sensitivity rating, matching the original part's environmental specifications. The TO-220FP package is mechanically compatible with TO-220ABFP footprints in standard through-hole applications.

For Enhanced Performance Applications:

The R6015ENX (Rohm Semiconductor) and STF18N60M2 (STMicroelectronics) offer higher current ratings (15A and 13A respectively) at 600V Vdss with improved Rds On characteristics. Both are Active status products with full RoHS3 compliance. These parts are suitable when design margins allow for higher current capability without voltage derating.

For Higher Voltage Margin Applications:

The STF17N80K5 and STF18NM80 provide 800V Vdss rating with 14A and 17A continuous drain current respectively. These parts are appropriate for applications requiring enhanced voltage headroom or where 600V margin is insufficient. Both are Active status with RoHS3 compliance.

Parts to Avoid:

The SPA11N65C3XKSA1 (Infineon Technologies) is classified as "Not For New Designs" and should not be selected for new production applications, despite its technical compatibility.

Frequently Asked Questions (FAQ)

Q: Can the STF13N60M2 directly replace the IXKP13N60C5M without circuit modification?

A: The STF13N60M2 is electrically compatible for most applications. Both parts share 600V Vdss rating, 10V gate drive voltage, and TO-220-3 package footprint. The STF13N60M2 provides 11A continuous drain current versus the original 6.5A, offering design margin. Gate charge is lower (17 nC vs. 30 nC), resulting in faster switching. No circuit modification is required for standard switching applications; however, gate drive timing may improve due to reduced gate charge.

Q: What is the difference between STF13N60M2 and STF13NM60ND?

A: Both parts are STMicroelectronics N-Channel 600V 11A MOSFETs in TO-220FP packages. The primary differences are gate charge (17 nC vs. 24.5 nC) and input capacitance measurement conditions (100V vs. 50V). The STF13N60M2 belongs to the MDmesh™ II Plus series, while STF13NM60ND belongs to the FDmesh™ II series. Both are Active status and RoHS3 compliant. Selection between them depends on specific switching frequency and gate drive circuit requirements.

Q: Why is the FDPF17N60NT listed as a substitute if it has higher current rating?

A: The FDPF17N60NT (onsemi UniFET™) maintains the critical 600V Vdss specification and 10V gate drive compatibility. Its 17A continuous drain current exceeds the 6.5A requirement, providing substantial design margin. The higher current rating does not prevent substitution; it indicates the part can handle the original application with additional capacity. This part is suitable when higher current capability is beneficial or when design evolution requires increased current headroom.

Q: Are all substitute parts RoHS3 compliant?

A: Yes. All substitute parts listed are RoHS3 compliant. The original IXKP13N60C5M is also RoHS3 compliant. This ensures environmental and regulatory compatibility across all recommended substitutes.

Q: What is the significance of the TO-220FP versus TO-220ABFP package designation?

A: Both designations refer to TO-220-3 Full Pack through-hole packages with identical PCB footprints and pin configurations. The suffix variations (FP, ABFP, FM, F-3) indicate manufacturer-specific package nomenclature but do not affect mechanical or electrical compatibility in standard through-hole applications. All listed substitutes are mechanically interchangeable on existing PCB layouts.

Q: Can I use the STF17N80K5 or STF18NM80 (800V parts) in a 600V design?

A: Yes. The 800V Vdss rating provides additional voltage margin and does not degrade performance in 600V applications. These parts are suitable when design evolution or field conditions may expose the circuit to transient overvoltages. The higher voltage rating introduces no functional penalty; however, gate charge and input capacitance are higher, which may affect switching speed and gate drive power consumption.

Q: What is the MSL (Moisture Sensitivity Level) rating and why does it matter?

A: MSL 1 (Unlimited) indicates the component has no moisture sensitivity restrictions and requires no special handling or storage conditions. All recommended substitutes maintain MSL 1 rating, ensuring compatibility with standard manufacturing and storage practices. This eliminates the need for specialized moisture-controlled environments or baking procedures before soldering.

Q: Is the SPA11N65C3XKSA1 suitable for new designs?

A: No. The SPA11N65C3XKSA1 is classified as "Not For New Designs" by Infineon Technologies. While it is technically compatible (650V Vdss, 11A Id, TO-220-3 package), this status indicates the manufacturer is discontinuing support and recommends alternative parts for new production. This part should be reserved only for field replacements of existing equipment where no other option exists.

Q: How do I determine which substitute is best for my specific application?

A: Selection depends on three factors: (1) Current requirement – if your circuit draws less than 6.5A, any substitute with equal or higher rating is acceptable; (2) Voltage margin – if 600V is marginal, consider 800V parts; (3) Switching frequency – lower gate charge (STF13N60M2, STF15N60M2-EP) is preferred for high-frequency applications. All Active status parts are suitable for new designs. Consult your gate drive circuit specifications and thermal design to finalize selection.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message