IRF3205STRRPBF N-Channel MOSFET Equivalent & Substitute Parts

Part Overview

The IRF3205STRRPBF is an N-Channel MOSFET manufactured by Infineon Technologies, rated for 55V drain-to-source voltage and 110A continuous drain current in a D2PAK surface mount package. This device is classified as Obsolete product status. Due to obsolescence, equivalent substitute parts with matching or superior electrical and mechanical specifications are required for design continuity and procurement alternatives.

Key Parameters

Parameter	Value	Unit
Drain to Source Voltage (Vdss)	55	V
Continuous Drain Current (Id) @ 25°C	110	A
Rds On (Max) @ 62A, 10V	8	mOhm
Gate Threshold Voltage (Vgs(th)) @ 250µA	4	V
Gate Charge (Qg) @ 10V	146	nC
Power Dissipation (Max)	200	W
Operating Temperature Range	-55 to 175	°C
Package Type	D2PAK (TO-263-3)	—
Mounting Type	Surface Mount	—
RoHS Status	ROHS3 Compliant	—

Substitute Part Grouping Explanation

Substitution of the IRF3205STRRPBF is determined by the following critical parameters:

Primary Matching Criteria:

Drain-to-Source Voltage (Vdss): 55V or higher
Continuous Drain Current (Id): 110A or higher at 25°C
Package Type: D2PAK (TO-263-3) surface mount
Operating Temperature Range: -55°C to 175°C minimum
RoHS Compliance: ROHS3 Compliant

Secondary Compatibility Factors:

Rds On (Max): 8 mOhm or lower for equivalent performance
Gate Threshold Voltage: 4V or lower for drive compatibility
Gate Charge: 146 nC or lower for switching efficiency
Power Dissipation: 200W or higher for thermal margin

Substitute parts are grouped into two categories:

Category 1: Direct Packaging Equivalent (Tape & Reel) IRF3205STRLPBF maintains identical electrical specifications with Active product status and alternative packaging format (Cut Tape & Digi-Reel®).

Category 2: Functional Substitutes (55V, 75A Rating) Parts with 55V Vdss and 75A continuous drain current in D2PAK package. These devices operate within the same voltage class and package footprint. Current rating of 75A is lower than the original 110A specification; selection requires application-level current demand analysis.

Category 3: Functional Substitutes (60V Rating) Parts with 60V Vdss and 50A continuous drain current. These devices provide higher voltage margin but reduced current capacity. Selection requires verification that application current demands do not exceed 50A.

Category 4: Functional Substitutes (75V Rating) Parts with 75V Vdss and 75A continuous drain current. These devices provide enhanced voltage headroom for higher-voltage applications.

Parameter Comparison

Part Number	Manufacturer	Vdss (V)	Id @ 25°C (A)	Rds On Max (mOhm)	Vgs(th) (V)	Qg (nC)	Power Diss. (W)	Package	Status
IRF3205STRRPBF	Infineon	55	110	8	4	146	200	D2PAK	Obsolete
IRF3205STRLPBF	Infineon	55	110	8	4	146	200	D2PAK	Active
IPB081N06L3GATMA1	Infineon	60	50	8.1	2.2	29	79	D2PAK	Active
IPB090N06N3GATMA1	Infineon	60	50	9	4	36	71	D2PAK	Active
BUK7610-55AL,118	Nexperia	55	75	10	4	124	300	D2PAK	Obsolete
BUK764R0-55B,118	Nexperia	55	75	4	4	86	300	D2PAK	Active
BUK9608-55B,118	Nexperia	55	75	7	2	45	203	D2PAK	Active
BUK9612-55B,118	Nexperia	55	75	10	2	31	157	D2PAK	Active
HUF75345S3ST	onsemi	55	75	7	4	275	325	D2PAK	Active
PHB191NQ06LT,118	Nexperia	55	75	3.7	2	95.6	300	D2PAK	Active
PSMN008-75B,118	Nexperia	75	75	8.5	4	122.8	230	D2PAK	Active

Engineering Selection Recommendations

Primary Recommendation: IRF3205STRLPBF

IRF3205STRLPBF is the direct equivalent substitute for IRF3205STRRPBF. This part maintains identical electrical specifications (55V, 110A, 8 mOhm Rds On, 200W power dissipation) and D2PAK package configuration. The only difference is packaging format (Cut Tape & Digi-Reel® versus Tape & Reel). Product status is Active, ensuring long-term availability and supply chain continuity. RoHS3 compliance and REACH unaffected status match the original part. This substitution requires no circuit redesign or thermal analysis modifications.

Secondary Recommendations for Current-Limited Applications:

For applications where continuous drain current requirement is 75A or lower, the following 55V-rated parts provide Active product status and D2PAK packaging:

BUK764R0-55B,118 (Nexperia, Active): 55V, 75A, 4 mOhm Rds On, 300W dissipation. Automotive-grade with AEC-Q101 qualification. Superior Rds On performance reduces conduction losses.
BUK9612-55B,118 (Nexperia, Active): 55V, 75A, 10 mOhm Rds On, 157W dissipation. Automotive-grade with AEC-Q101 qualification. Highest inventory availability (500,400 pcs). Lower gate charge (31 nC) improves switching speed.
PHB191NQ06LT,118 (Nexperia, Active): 55V, 75A, 3.7 mOhm Rds On, 300W dissipation. Lowest on-resistance among 55V substitutes, minimizing conduction losses in high-current applications.
HUF75345S3ST (onsemi, Active): 55V, 75A, 7 mOhm Rds On, 325W dissipation. Highest power dissipation rating provides maximum thermal margin.

Tertiary Recommendations for Voltage-Margin Applications:

For applications requiring higher voltage headroom with reduced current capacity:

PSMN008-75B,118 (Nexperia, Active): 75V, 75A, 8.5 mOhm Rds On, 230W dissipation. Provides 20V additional voltage margin while maintaining 75A current capacity.

Not Recommended for Direct Substitution:

IPB081N06L3GATMA1 and IPB090N06N3GATMA1 (both 60V, 50A) are unsuitable as direct substitutes due to 50A maximum continuous drain current, which is 60A below the original 110A specification. These parts are applicable only in applications with confirmed maximum current demand below 50A.

Frequently Asked Questions (FAQ)

Q1: Can IRF3205STRLPBF directly replace IRF3205STRRPBF without circuit modification?

A: Yes. IRF3205STRLPBF is electrically and mechanically identical to IRF3205STRRPBF. The only difference is packaging format (Cut Tape & Digi-Reel® versus Tape & Reel). No circuit redesign, PCB layout changes, or thermal analysis modifications are required. Both parts are D2PAK surface mount packages with identical pin configuration and electrical ratings.

Q2: Why are 75A-rated parts listed as substitutes for a 110A device?

A: 75A-rated substitutes are applicable only when application circuit analysis confirms that maximum continuous drain current requirement does not exceed 75A. These parts maintain the same 55V voltage rating and D2PAK package footprint. Selection of a 75A part for an application requiring 110A continuous current will result in device thermal stress and potential failure. Application current demand must be verified before selecting any 75A substitute.

Q3: What is the difference between BUK764R0-55B,118 and BUK9612-55B,118?

A: Both parts are 55V, 75A Nexperia TrenchMOS™ devices in D2PAK packages with Active status and AEC-Q101 automotive qualification. Key differences: BUK764R0-55B,118 has 4 mOhm Rds On and 300W power dissipation; BUK9612-55B,118 has 10 mOhm Rds On and 157W power dissipation. BUK764R0-55B,118 provides superior conduction efficiency (lower Rds On) but requires more thermal management. BUK9612-55B,118 has significantly higher inventory availability (500,400 pcs) and lower gate charge (31 nC) for faster switching.

Q4: Can IPB081N06L3GATMA1 or IPB090N06N3GATMA1 be used as substitutes?

A: These parts are not suitable as direct substitutes. Both are rated for only 50A continuous drain current, compared to the original 110A specification. They are applicable only in applications where maximum continuous current demand is confirmed to be 50A or lower. Using these parts in higher-current applications will cause thermal runaway and device failure. Verify application current requirements before considering these alternatives.

Q5: What does "Automotive Grade" and "AEC-Q101" qualification mean for substitute selection?

A: Automotive-grade devices with AEC-Q101 qualification meet stringent automotive industry reliability and quality standards. These parts undergo enhanced testing for temperature cycling, moisture resistance, and long-term reliability. If the original application requires automotive-grade components, select only substitute parts explicitly marked with "Grade: Automotive" and "Qualification: AEC-Q101" (such as BUK764R0-55B,118, BUK9608-55B,118, BUK9612-55B,118, and PHB191NQ06LT,118). Non-automotive-grade parts may not meet application reliability requirements.

Q6: Why is PSMN008-75B,118 listed with 75V rating instead of 55V?

A: PSMN008-75B,118 is a 75V-rated device, providing 20V additional voltage margin compared to the original 55V specification. This part is applicable in applications where higher voltage headroom is beneficial or required. The 75V rating does not prevent use in 55V applications; it simply provides additional safety margin. However, this part maintains only 75A continuous drain current, which is 35A below the original 110A specification. Selection requires confirmation that application current demand does not exceed 75A.

Q7: What is the significance of "RoHS3 Compliant" and "REACH Unaffected" status?

A: RoHS3 Compliance indicates the part meets Restriction of Hazardous Substances Directive requirements, restricting lead, cadmium, mercury, and other hazardous materials. REACH Unaffected status indicates the part is not subject to Registration, Evaluation, Authorization, and Restriction of Chemicals regulations. All listed substitute parts maintain RoHS3 compliance and REACH unaffected status, matching the original part's environmental and regulatory compliance profile. This ensures compatibility with procurement policies and regulatory requirements.

Q8: What is the difference between "Tape & Reel (TR)" and "Cut Tape (CT) & Digi-Reel®" packaging?

A: Both are surface mount packaging formats suitable for automated assembly. Tape & Reel (TR) provides continuous reel format for high-volume production. Cut Tape (CT) & Digi-Reel® provides smaller quantities in tape format, suitable for lower-volume or prototype applications. Both formats use identical D2PAK component packages and are mechanically and electrically interchangeable. Selection depends on procurement volume and assembly equipment compatibility, not electrical performance.

Q9: Can multiple substitute parts be used interchangeably within a single design?

A: No. Each substitute part has distinct electrical characteristics (Rds On, gate charge, power dissipation, threshold voltage). Using different parts in the same circuit design may result in uneven current distribution, thermal imbalance, and reliability issues. Select a single substitute part for all instances of the original IRF3205STRRPBF within a design. If multiple part numbers are used, conduct separate thermal and electrical analysis for each configuration.

Q10: What is the impact of lower gate charge (Qg) on circuit performance?

A: Lower gate charge reduces the energy required to switch the MOSFET on and off, resulting in faster switching speed and reduced switching losses. Parts with lower Qg (such as IPB081N06L3GATMA1 at 29 nC or BUK9612-55B,118 at 31 nC) are advantageous in high-frequency switching applications. However, lower Qg may require gate driver circuit optimization to ensure stable switching behavior. Verify gate driver compatibility before selecting parts with significantly different gate charge specifications.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message