IPS022G Equivalent & Substitute Parts

Part Overview

The IPS022G is a Power Management IC (PMIC) manufactured by Infineon Technologies, functioning as a PWR DRIVER N-CHANNEL 1:1 in an 8-SOIC package. This device operates as a Power Switch/Driver with 1:1 ratio, N-Channel output configuration, and 1A maximum output current. The IPS022G is classified as obsolete, making identification of compatible substitute components essential for ongoing system support and new design implementations.

Substiute Parts

IPS022G

Infineon TechnologiesIn Stock: 4667IPS022G Datasheet

Current PartRFQ

BTS3410GXUMA1

Infineon TechnologiesIn Stock: 1649BTS3410GXUMA1 Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution of the IPS022G is determined by strict alignment of the following electrical and mechanical parameters:

Critical Substitution Criteria:

• Switch Type: General Purpose
• Number of Outputs: 2
• Ratio - Input:Output: 1:1
• Output Configuration: Low Side
• Output Type: N-Channel
• Interface: On/Off
• Input Type: Non-Inverting
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (0.154", 3.90mm Width)

Allowable Parameter Variations:

• Voltage - Load (Max): Must be ≥35V
• Current - Output (Max): Must be ≥1A
• Rds On (Typ): May vary within acceptable operating margins
• Fault Protection: May include additional protection features
• Operating Temperature: Must maintain -40°C ~ 150°C range
• RoHS Status: May differ from original part

The BTS3410GXUMA1 meets all critical substitution criteria while providing enhanced electrical performance and additional fault protection features.

Parameter Comparison

Engineering Selection Recommendations

The BTS3410GXUMA1 is the manufacturer-recommended substitute for the obsolete IPS022G. Both devices are manufactured by Infineon Technologies and share identical functional architecture, package form factor, and thermal operating range.

Compliance Advantages: The BTS3410GXUMA1 achieves ROHS3 compliance, whereas the IPS022G is RoHS non-compliant. This distinction is significant for applications subject to regulatory compliance requirements.

Performance Enhancements: The BTS3410GXUMA1 provides increased voltage rating (42V vs. 35V) and higher current capacity (1.3A vs. 1A), offering design margin improvements for existing applications. The addition of Over Voltage fault protection provides enhanced system reliability compared to the original part's Current Limiting and Over Temperature protection.

Operational Compatibility: Both devices maintain identical operating temperature specifications (-40°C ~ 150°C TJ), interface type (On/Off), and output configuration (Low Side N-Channel). The 8-SOIC package dimensions are identical, enabling direct PCB layout compatibility.

Frequently Asked Questions (FAQ)

Q: Can the BTS3410GXUMA1 directly replace the IPS022G in existing designs?

A: Yes. Both devices share identical package geometry (8-SOIC), functional configuration (1:1 ratio, Low Side N-Channel, 2 outputs), and thermal operating range. Pin-to-pin compatibility is maintained, allowing direct substitution without PCB modification.

Q: What are the key electrical differences between these parts?

A: The BTS3410GXUMA1 provides higher voltage rating (42V vs. 35V maximum load voltage) and increased current capacity (1.3A vs. 1A maximum output current). The Rds On specification differs slightly (150mOhm vs. 130mOhm typical), and the BTS3410GXUMA1 includes additional Over Voltage fault protection.

Q: Does the higher Rds On value of the BTS3410GXUMA1 affect system performance?

A: The 20mOhm difference in Rds On (130mOhm to 150mOhm) represents a 15% increase in on-state resistance. For 1A operation, this results in approximately 20mW additional power dissipation. System thermal design should account for this variance.

Q: Are there moisture sensitivity considerations for the BTS3410GXUMA1?

A: The BTS3410GXUMA1 has MSL rating of 3 (168 hours), compared to MSL 1 (unlimited) for the IPS022G. This requires adherence to moisture control procedures during storage and handling, with a 168-hour floor life limit after moisture exposure.

Q: What is the significance of the RoHS compliance difference?

A: The IPS022G is RoHS non-compliant, while the BTS3410GXUMA1 is ROHS3 compliant. For applications subject to RoHS regulations or customer requirements, the BTS3410GXUMA1 is the appropriate selection.

Q: Are both parts available from the same manufacturer?

A: Yes. Both the IPS022G and BTS3410GXUMA1 are manufactured by Infineon Technologies. The BTS3410GXUMA1 is currently in active production status, whereas the IPS022G is obsolete.