IL-Z-5PL-SMTYE-R1500 Equivalent & Substitute Parts

Part Overview

The IL-Z-5PL-SMTYE-R1500 is a surface mount, right-angle rectangular connector header manufactured by JAE Electronics. This 5-position connector operates at 1.25mm pitch and is designed for board-to-cable/wire applications with solder termination and friction lock fastening. The part is currently obsolete, making identification of functionally equivalent alternatives essential for ongoing design support and production continuity.

Substiute Parts

IL-Z-5PL-SMTYE-R1500

JAE ElectronicsIn Stock: 919IL-Z-5PL-SMTYE-R1500 Datasheet

Current PartRFQ

DF13A-5P-1.25H(21)

Hirose Electric Co LtdIn Stock: 6445DF13A-5P-1.25H(21) Datasheet

SimilarRFQ

Key Parameters

Substitute Part Grouping Explanation

The DF13A-5P-1.25H(21) manufactured by Hirose Electric Co Ltd qualifies as a functional substitute based on the following critical parameters:

Matching Parameters:

• Connector Type: Header
• Contact Type: Male Pin
• Pitch - Mating: 0.049" (1.25mm)
• Number of Positions: 5
• Number of Rows: 1
• Mounting Type: Surface Mount, Right Angle
• Shrouding: Shrouded - 4 Wall
• Termination: Solder
• Current Rating: 1A
• Material Flammability Rating: UL94 V-0
• Moisture Sensitivity Level: 1 (Unlimited)

Differing Parameters:

• Fastening Type: Detent Lock (vs. Friction Lock on original)
• Insulation Height: 0.142" (3.60mm) vs. 0.136" (3.46mm)
• Operating Temperature: -35°C ~ 85°C (vs. -40°C ~ 70°C)
• Voltage Rating: 150V (vs. 200V)
• Product Status: Active (vs. Obsolete)

Parameter Comparison

Engineering Selection Recommendations

The DF13A-5P-1.25H(21) is an active product with equivalent electrical and mechanical specifications for standard applications. The substitute maintains the same pitch, position count, mounting orientation, and flammability rating as the original IL-Z-5PL-SMTYE-R1500.

The voltage rating difference (150V vs. 200V) and operating temperature range variation must be evaluated against application requirements. The fastening mechanism change from friction lock to detent lock and the minor insulation height increase (0.006") require mechanical fit verification in the target assembly.

The Hirose part is ROHS3 compliant and REACH unaffected, providing regulatory alignment for current production environments.

Frequently Asked Questions (FAQ)

Q: Can the DF13A-5P-1.25H(21) be used as a direct replacement for the IL-Z-5PL-SMTYE-R1500?

A: The DF13A-5P-1.25H(21) matches the critical electrical and mechanical parameters: 1.25mm pitch, 5-position single-row configuration, surface mount right-angle orientation, and solder termination. However, the fastening mechanism differs (detent lock vs. friction lock), and the insulation height is 0.006" taller. Mechanical fit verification in the target assembly is required.

Q: What are the key parameters that determine substitution compatibility?

A: Substitution compatibility is determined by: connector type (header), contact type (male pin), pitch (1.25mm), position count (5), row configuration (1), mounting type (surface mount right-angle), shrouding (4-wall), and termination method (solder). These parameters ensure physical and electrical interchangeability.

Q: Does the voltage rating difference affect substitution suitability?

A: The substitute part has a 150V rating versus the original 200V rating. Applications operating below 150V are unaffected. Applications requiring the full 200V rating must retain the original part or identify alternatives with matching voltage specifications.

Q: What is the impact of the fastening type change?

A: The original uses friction lock fastening, while the substitute uses detent lock. Both provide secure mating, but the engagement mechanism differs. Mating connector compatibility must be confirmed, as the detent lock may require a specific receptacle design.

Q: Are there packaging considerations for the substitute part?

A: The DF13A-5P-1.25H(21) is supplied in Tape & Reel (TR) packaging with 6400 pieces in stock, compared to the original part's unspecified packaging. Tape & Reel format is standard for surface mount production environments.