IL 511-1E Digital Isolator Equivalent & Substitute Parts

Part Overview

The IL 511-1E is a General Purpose Digital Isolator manufactured by NVE Corp/Isolation Products, part of the IsoLoop® series. This component provides 2500Vrms isolation across 2 channels with 2Mbps data rate and 30kV/µs common mode transient immunity. The IL 511-1E operates with supply voltages from 3V to 5.5V and is housed in an 8-MSOP surface mount package.

The IL 511-1E is classified as Obsolete. Identifying equivalent and substitute parts is necessary for design continuity, procurement planning, and system redesign when original inventory becomes unavailable. Substitute parts must maintain functional compatibility within the specified electrical and mechanical parameters.

Key Parameters

Parameter	IL 511-1E Value
Manufacturer	NVE Corp/Isolation Products
Series	IsoLoop®
Product Status	Obsolete
Technology	GMR (Giant Magnetoresistive)
Number of Channels	2
Voltage - Isolation	2500Vrms
Common Mode Transient Immunity (Min)	30kV/µs
Data Rate	2Mbps
Voltage - Supply	3V ~ 5.5V
Operating Temperature	-40°C ~ 85°C
Package / Case	8-TSSOP, 8-MSOP (0.118", 3.00mm Width)
RoHS Status	ROHS3 Compliant
Moisture Sensitivity Level (MSL)	1 (Unlimited)

Substitute Part Grouping Explanation

Substitute parts for the IL 511-1E are identified based on the following critical parameters that determine functional compatibility:

Primary Substitution Criteria:

Voltage - Isolation: 2500Vrms (mandatory match)
Number of Channels: 2 (mandatory match for full functionality)
Channel Type: Unidirectional (mandatory match)
Voltage - Supply: 3V ~ 5.5V (mandatory match)
Technology: GMR (Giant Magnetoresistive) (preferred for consistency)
Mounting Type: Surface Mount (mandatory match)

Secondary Compatibility Factors:

Common Mode Transient Immunity: 30kV/µs or higher
Data Rate: 2Mbps or higher
Operating Temperature range compatibility
RoHS compliance status
Package compatibility (8-pin surface mount variants)

The IL 511-1E has two identified substitute categories:

Parametric Equivalent: IL 510-1E differs only in channel count (1 channel vs. 2 channels) and is suitable only for applications requiring single-channel isolation.

Similar Substitutes: HCPL-9030-300E, HCPL-9000-500E, and HCPL-9000-500 are Broadcom Limited products that maintain 2500Vrms isolation and 2-channel configuration but operate at higher data rates (110MBd) and lower CMTI (15kV/µs). These parts are Active status and ROHS3 compliant.

Parameter Comparison

Parameter	IL 511-1E	IL 510-1E	HCPL-9030-300E	HCPL-9000-500E	HCPL-9000-500
Manufacturer	NVE Corp	NVE Corp	Broadcom Limited	Broadcom Limited	Broadcom Limited
Number of Channels	2	1	2	1	1
Voltage - Isolation	2500Vrms	2500Vrms	2500Vrms	2500Vrms	2500Vrms
CMTI (Min)	30kV/µs	30kV/µs	15kV/µs	15kV/µs	15kV/µs
Data Rate	2Mbps	2Mbps	110MBd	110MBd	110MBd
Propagation Delay tpLH / tpHL (Max)	25ns / 25ns	25ns / 25ns	15ns / 15ns	15ns / 15ns	15ns / 15ns
Pulse Width Distortion (Max)	10ns	10ns	3ns	3ns	3ns
Voltage - Supply	3V ~ 5.5V	3V ~ 5.5V	3V ~ 5.5V	3V ~ 5.5V	3V ~ 5.5V
Operating Temperature	-40°C ~ 85°C	-40°C ~ 85°C	-55°C ~ 125°C	-55°C ~ 125°C	-55°C ~ 125°C
Product Status	Obsolete	Obsolete	Active	Active	Active
RoHS Status	ROHS3 Compliant	ROHS3 Compliant	ROHS3 Compliant	ROHS3 Compliant	RoHS non-compliant
Technology	GMR	GMR	GMR	GMR	GMR

Engineering Selection Recommendations

For Direct 2-Channel Replacement (IL 511-1E Equivalent):

HCPL-9030-300E is the primary substitute for applications requiring 2-channel isolation at 2500Vrms. This part is manufactured by Broadcom Limited and maintains Active product status, ensuring long-term availability and supply chain stability. HCPL-9030-300E is ROHS3 compliant and operates across an extended temperature range (-55°C to 125°C), providing broader environmental compatibility than the original IL 511-1E.

The HCPL-9030-300E operates at 110MBd data rate, which exceeds the IL 511-1E specification of 2Mbps. Common mode transient immunity is specified at 15kV/µs, which is lower than the IL 511-1E (30kV/µs). This reduction in CMTI must be evaluated against application requirements for high-speed transient environments.

For Single-Channel Applications:

HCPL-9000-500E and HCPL-9000-500 are suitable for applications requiring only single-channel isolation. HCPL-9000-500E is ROHS3 compliant and Active status. HCPL-9000-500 is RoHS non-compliant and should be selected only when RoHS compliance is not a design requirement.

For Obsolete Part Continuity:

IL 510-1E is an NVE Corp alternative within the same IsoLoop® series but provides only 1-channel isolation. This part is also Obsolete and should not be selected for new designs requiring long-term supply assurance.

Frequently Asked Questions (FAQ)

Q: Can HCPL-9030-300E directly replace IL 511-1E in existing designs?

A: HCPL-9030-300E maintains the same 2500Vrms isolation voltage, 2-channel configuration, and 3V to 5.5V supply range as IL 511-1E. However, the lower CMTI specification (15kV/µs vs. 30kV/µs) must be verified against application requirements. The higher data rate (110MBd vs. 2Mbps) and faster propagation delay (15ns vs. 25ns) are compatible with IL 511-1E timing requirements. Package compatibility must be confirmed for the specific PCB layout.

Q: What is the difference between HCPL-9000-500 and HCPL-9000-500E?

A: Both parts are identical in electrical specifications and package configuration. The primary difference is RoHS compliance status: HCPL-9000-500E is ROHS3 compliant, while HCPL-9000-500 is RoHS non-compliant. For applications subject to RoHS regulations, HCPL-9000-500E must be selected.

Q: Why is IL 510-1E listed as a substitute if it has only 1 channel?

A: IL 510-1E is a parametric equivalent within the NVE Corp IsoLoop® series, sharing identical electrical specifications except for channel count. It is suitable only for applications that require single-channel isolation. For applications requiring 2-channel isolation, IL 510-1E is not a functional substitute.

Q: Are there package compatibility issues between IL 511-1E and HCPL-9030-300E?

A: IL 511-1E uses 8-MSOP packaging (0.118", 3.00mm width). HCPL-9030-300E uses 8-SMD Gull Wing packaging. While both are 8-pin surface mount packages, the physical dimensions and pin configurations differ. PCB layout modifications may be required for direct substitution.

Q: What is the operating temperature range difference, and does it affect substitution?

A: IL 511-1E operates from -40°C to 85°C. HCPL-9030-300E, HCPL-9000-500E, and HCPL-9000-500 operate from -55°C to 125°C. The extended range of Broadcom parts provides additional environmental margin and is compatible with IL 511-1E applications. Applications operating within the IL 511-1E temperature range will function within the Broadcom part specifications.

Q: Is the reduction in CMTI from 30kV/µs to 15kV/µs a critical limitation?

A: CMTI specification determines the maximum rate of change of common-mode voltage that the isolator can withstand without introducing errors. The reduction from 30kV/µs to 15kV/µs must be evaluated against the specific application environment. Applications with slower transient rates or lower noise coupling will not be affected. High-speed switching environments or high-dI/dt circuits may require verification.

Q: Can IL 511-1E be used in new designs, or should Broadcom parts be selected?

A: IL 511-1E is classified as Obsolete. New designs should select Active status parts such as HCPL-9030-300E to ensure long-term supply availability and manufacturing support. Existing designs using IL 511-1E may continue operation with available inventory, but redesign planning should begin to transition to Active alternatives.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message