HM2P07PDT2C0N9 110-Position 2mm Press-Fit Backplane Connector

Part Overview

The HM2P07PDT2C0N9 is a 110-position header connector with male pins, 0.079" (2.00mm) pitch, designed for through-hole press-fit mounting on backplane applications. Manufactured by Amphenol ICC (FCI) under the Millipacs® series, this connector features a 5-row configuration with gold-plated contacts rated for 1.5A at 750Vrms across an operating temperature range of -55°C to 125°C.

The HM2P07PDT2C0N9 is classified as obsolete. Equivalent and substitute parts are available from active product lines, providing direct functional replacement with improved compliance status and availability.

Key Parameters

Parameter	Value
Connector Type	Header, Male Pins
Number of Positions	110
Pitch	0.079" (2.00mm)
Number of Rows	5
Mounting Type	Through Hole
Termination	Press-Fit
Contact Finish	Gold
Current Rating	1.5 A
Voltage Rating	750Vrms
Operating Temperature	-55°C to 125°C
Features	Board Guide

Substitute Part Grouping Explanation

Substitution eligibility is determined by strict equivalence across the following parameters: connector type (header, male pins), number of positions (110), pitch (2.00mm), number of rows (5), mounting type (through hole), termination method (press-fit), operating temperature range (-55°C to 125°C), and connector style (A 22). All substitute parts listed maintain these core specifications.

Voltage and current ratings vary among substitutes. The HM2P07PDT2C0N9 operates at 750Vrms with 1.5A rating. Substitute parts from TE Connectivity (Z-PACK series) and HARTING (har-bus® HM series) operate at 500Vrms with either 1.5A or 1.0A ratings. These differences reflect design variations within the same functional category and do not prevent substitution in applications where the lower voltage or current specifications are acceptable.

Contact finish specifications also vary: the original part specifies 30.0µin (0.76µm) gold plating, while HM2P07PDT2C0N9LF uses flash gold plating, and HARTING parts specify gold or gold-palladium without thickness specification.

Parameter Comparison

Part Number	Manufacturer	Series	Positions	Pitch	Rows	Mounting	Termination	Current (A)	Voltage (Vrms)	Temp Range	Contact Finish	Product Status	RoHS Status
HM2P07PDT2C0N9	Amphenol ICC (FCI)	Millipacs®	110	2.00mm	5	Through Hole	Press-Fit	1.5	750	-55 to 125°C	Gold 30.0µin	Obsolete	Non-compliant
HM2P07PDT2C0N9LF	Amphenol ICC (FCI)	Millipacs®	110	2.00mm	5	Through Hole	Press-Fit	1.5	750	-55 to 125°C	Gold Flash	Active	Compliant
1-5100143-9	TE Connectivity AMP	Z-PACK	110	2.00mm	5	Through Hole	Press-Fit	1.5	500	-55 to 125°C	Gold	Active	ROHS3 Compliant
1-5188398-9	TE Connectivity AMP	Z-PACK	110	2.00mm	5	Through Hole	Press-Fit	1.5	500	-55 to 125°C	Gold 30.0µin	Active	ROHS3 Compliant
17011102204	HARTING	har-bus® HM	110	2.00mm	5	Through Hole	Press-Fit	1.0	—	-55 to 125°C	Gold or Gold-Palladium	Active	ROHS3 Compliant
17011102402	HARTING	har-bus® HM	110	2.00mm	5	Through Hole	Press-Fit	1.0	—	-55 to 125°C	Gold or Gold-Palladium	Active	ROHS3 Compliant
17011104201	HARTING	har-bus® HM	110	2.00mm	5	Through Hole	Press-Fit	1.0	—	-55 to 125°C	Gold or Gold-Palladium	Active	ROHS3 Compliant
3-5100143-0	TE Connectivity AMP	Z-PACK	110	2.00mm	5	Through Hole	Press-Fit	1.5	500	-55 to 125°C	Gold 30.0µin	Active	Compliant
5100143-1	TE Connectivity AMP	Z-PACK	110	2.00mm	5	Through Hole	Press-Fit	1.5	500	-55 to 125°C	Gold 30.0µin	Active	ROHS3 Compliant
5106164-1	TE Connectivity AMP	Z-PACK	110	2.00mm	5	Through Hole	Press-Fit	1.5	500	-55 to 125°C	Gold 30.0µin	Active	ROHS3 Compliant
5106413-1	TE Connectivity AMP	Z-PACK	110	2.00mm	5	Through Hole	Press-Fit	1.5	500	-55 to 125°C	Gold 30.0µin	Active	ROHS3 Compliant

Engineering Selection Recommendations

The HM2P07PDT2C0N9 is obsolete and no longer in active production. Direct replacement with active-status equivalents is necessary for new designs and ongoing procurement.

Primary Recommendation: HM2P07PDT2C0N9LF

This part is the direct successor from Amphenol ICC (FCI), maintaining the same manufacturer, series (Millipacs®), and electrical specifications (1.5A, 750Vrms). The only difference is contact finish (flash gold versus 30.0µin plating) and RoHS compliance status (active product, RoHS compliant). This is the preferred choice for direct substitution with minimal design impact.

Secondary Recommendations: TE Connectivity Z-PACK Series (1-5100143-9, 1-5188398-9, 3-5100143-0, 5100143-1, 5106164-1, 5106413-1)

These parts maintain 1.5A current rating and full 110-position, 2.00mm pitch configuration. Voltage rating is reduced to 500Vrms. All are active products with ROHS3 compliance. Selection among these variants depends on specific feature requirements (5106164-1 includes alignment strip) and REACH compliance status. These are suitable where 500Vrms specification meets application requirements.

Tertiary Recommendations: HARTING har-bus® HM Series (17011102204, 17011102402, 17011104201)

These parts maintain the 110-position, 2.00mm pitch, 5-row configuration and operating temperature range. Current rating is reduced to 1.0A, and voltage rating is not specified. All are active products with ROHS3 compliance. These are suitable only for applications where 1.0A current capacity is sufficient.

Frequently Asked Questions (FAQ)

Q: Can HM2P07PDT2C0N9LF be used as a direct replacement for HM2P07PDT2C0N9?

A: Yes. HM2P07PDT2C0N9LF is the active-production equivalent from the same manufacturer and series. Electrical specifications (1.5A, 750Vrms) and mechanical configuration (110 positions, 2.00mm pitch, 5 rows, through-hole press-fit) are identical. The contact finish differs (flash gold versus 30.0µin), and the newer part is RoHS compliant.

Q: What is the key difference between Amphenol ICC and TE Connectivity substitutes?

A: Amphenol ICC (HM2P07PDT2C0N9LF) maintains the original 750Vrms rating. TE Connectivity Z-PACK series (1-5100143-9, 1-5188398-9, and related variants) operate at 500Vrms. Both maintain 1.5A current rating and identical mechanical configuration. Selection depends on voltage requirement in the application.

Q: Are HARTING har-bus® HM parts suitable substitutes?

A: HARTING parts (17011102204, 17011102402, 17011104201) maintain mechanical compatibility (110 positions, 2.00mm pitch, 5 rows, through-hole press-fit) and operating temperature range. However, current rating is reduced to 1.0A, and voltage rating is not specified. These are suitable only where 1.0A current capacity is acceptable.

Q: What does "press-fit" termination mean for substitution purposes?

A: Press-fit termination indicates the connector pins are inserted into plated through-holes on the PCB under mechanical pressure, without soldering. All listed substitutes use identical press-fit termination, ensuring compatibility with existing PCB designs and assembly processes.

Q: How does packaging affect substitution?

A: Packaging (tray, tube) affects handling and storage but does not impact electrical or mechanical compatibility. The HM2P07PDT2C0N9 has no specified packaging; substitutes are available in tray or tube packaging. Packaging selection should be based on assembly process requirements and inventory management practices.

Q: What is the significance of RoHS compliance status?

A: The original HM2P07PDT2C0N9 is RoHS non-compliant. All active substitutes listed are RoHS3 compliant or RoHS compliant, meeting current regulatory requirements for new designs and procurement in regulated markets. This is a key reason for transitioning to substitute parts.

Q: Can I mix different substitute parts in the same assembly?

A: All listed substitutes are mechanically and functionally equivalent within their specified electrical ratings. Mixing parts with different voltage or current ratings (e.g., 750Vrms with 500Vrms, or 1.5A with 1.0A) in the same assembly is not recommended without circuit analysis to confirm all parts operate within their respective specifications.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message