HM2P07PDP265N9LLF Equivalent & Substitute Parts

Part Overview

The HM2P07PDP265N9LLF is a 132-position backplane connector header manufactured by Amphenol ICC (FCI) in the Millipacs® series. This through-hole press-fit connector features a 2.00mm pitch and supports applications requiring high-density interconnection with integrated ground positions (110 signal + 22 ground positions). The connector is actively produced and widely used in industrial and telecommunications backplane applications where reliable press-fit termination and board-level integration are required. Equivalent and substitute parts are identified to provide design flexibility, inventory alternatives, and sourcing options when the primary part is unavailable or when design requirements permit functional alternatives.

Substiute Parts

HM2P07PDP265N9LLF

Amphenol ICC (FCI)In Stock: 964HM2P07PDP265N9LLF Datasheet

Current PartRFQ

17011102402

HARTINGIn Stock: 89717011102402 Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the HM2P07PDP265N9LLF is determined by the following critical parameters:

Pitch (0.079" / 2.00mm): All substitute parts must maintain identical pitch to ensure PCB footprint compatibility and connector mating alignment.

Mounting Type (Through Hole) and Termination (Press-Fit): Substitute parts must use identical mounting and termination methods to ensure board integration compatibility.

Connector Type (Header, Male Pins): Substitute parts must maintain the same connector gender and pin configuration.

Operating Temperature Range (-55°C ~ 125°C): Substitute parts must support the full operating temperature range or equivalent.

Voltage and Current Ratings: Substitute parts must meet or exceed the electrical specifications (750Vrms, 1.5A minimum).

RoHS and Compliance Status: Substitute parts must maintain equivalent or superior compliance certifications.

The identified substitute part 17011102402 (HARTING har-bus® HM series) meets the core substitution criteria of pitch, mounting type, termination method, and operating temperature range. However, this part features 110 positions (signal only, without integrated ground positions) compared to the 132-position configuration of the main part. This represents a functional alternative for applications where the specific position count and ground integration of the HM2P07PDP265N9LLF are not mandatory design requirements.

Parameter Comparison

Engineering Selection Recommendations

Selection between the HM2P07PDP265N9LLF and substitute part 17011102402 depends on application-specific position requirements and electrical specifications.

The HM2P07PDP265N9LLF is the primary choice for applications requiring 132-position connectivity with integrated ground distribution (22 dedicated ground positions). This configuration provides enhanced signal integrity and ground plane management in high-density backplane applications. The part maintains active production status, RoHS compliance, and a current rating of 1.5A at 750Vrms.

The 17011102402 substitute is suitable for applications where 110-position connectivity is sufficient and integrated ground positions are not required. This part is also actively produced and maintains ROHS3 compliance with equivalent operating temperature range. However, the current rating is specified at 1A, which is lower than the main part. The voltage rating is not specified in available documentation. Selection of this substitute requires confirmation that the reduced current capacity and unspecified voltage rating are acceptable for the target application.

Both parts share identical pitch (2.00mm), mounting type (through hole), and termination method (press-fit), ensuring PCB footprint compatibility when position count differences are accommodated in the design.

Frequently Asked Questions (FAQ)

Q: Can the 17011102402 be used as a direct replacement for the HM2P07PDP265N9LLF?

A: Direct replacement is not possible due to position count differences. The HM2P07PDP265N9LLF provides 132 positions (110 signal + 22 ground), while the 17011102402 provides 110 positions without integrated ground positions. PCB layout and connector footprint must be redesigned to accommodate the 17011102402.

Q: Are the pitch and mounting specifications identical between these parts?

A: Yes. Both parts feature 0.079" (2.00mm) pitch and through-hole press-fit termination, ensuring compatibility with the same PCB footprint pattern when position count is adjusted.

Q: What are the electrical differences between these connectors?

A: The HM2P07PDP265N9LLF is rated for 1.5A at 750Vrms. The 17011102402 is rated for 1A; voltage rating is not specified. Applications requiring the full 1.5A capacity or 750Vrms rating must use the main part.

Q: Do both parts meet RoHS requirements?

A: Yes. The HM2P07PDP265N9LLF is RoHS Compliant. The 17011102402 is ROHS3 Compliant. Both meet current RoHS standards.

Q: What is the difference in packaging between these parts?

A: The HM2P07PDP265N9LLF is supplied in Tray packaging. The 17011102402 is supplied in Tube packaging. Packaging selection may affect handling, storage, and integration into assembly processes.

Q: Are the operating temperature ranges the same?

A: Yes. Both parts operate across the identical temperature range of -55°C to 125°C.

Q: What contact finish options are available?

A: The HM2P07PDP265N9LLF features Gold flash finish. The 17011102402 offers Gold or Gold-Palladium finish options. Contact finish selection may affect signal integrity and environmental resistance in specific applications.