HM2P07PDP255N9L Equivalent & Substitute Parts

Part Overview

The HM2P07PDP255N9L is a 132-position header connector (110 signal + 22 ground positions) manufactured by Amphenol ICC (FCI) in the Millipacs® series. This through-hole, press-fit connector operates at 1.5A per contact with a 750Vrms voltage rating across an operating temperature range of -55°C to 125°C. The part is currently listed as obsolete, making identification of equivalent and substitute components essential for ongoing system support and new design implementations.

Substiute Parts

HM2P07PDP255N9L

Amphenol ICC (FCI)In Stock: 851HM2P07PDP255N9L Datasheet

Current PartRFQ

HM2P07PDP255N9LLF

Amphenol ICC (FCI)In Stock: 717HM2P07PDP255N9LLF Datasheet

DirectRFQ

17011102402

HARTINGIn Stock: 89717011102402 Datasheet

MFR RecommendedRFQ

3-5100143-0

TE Connectivity AMP ConnectorsIn Stock: 10903-5100143-0 Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

Substitution eligibility for the HM2P07PDP255N9L is determined by the following critical parameters: connector type (header, male pins), pitch (2.00mm), mounting method (through-hole, press-fit), contact finish (gold), operating temperature range (-55°C to 125°C), and board guide feature.

The substitute parts are grouped into two categories:

Direct Equivalent (Same Position Count): HM2P07PDP255N9LLF maintains identical electrical and mechanical specifications as the original part, differing only in packaging (tray versus unspecified) and product status (active versus obsolete).

Functional Alternatives (Reduced Position Count): 17011102402 (HARTING) and 3-5100143-0 (TE Connectivity) provide 110-position configurations instead of 132 positions. These parts satisfy the core electrical parameters (2.00mm pitch, press-fit termination, gold contact finish, -55°C to 125°C operation, board guide) but require system-level evaluation due to reduced position capacity and differing current/voltage ratings.

Parameter Comparison

Engineering Selection Recommendations

HM2P07PDP255N9LLF is the primary substitute for the obsolete HM2P07PDP255N9L. This part maintains identical position count, electrical ratings, and mechanical specifications while offering active product status and RoHS compliance. The only difference is packaging format (tray). This substitution requires no design modification.

17011102402 (HARTING har-bus® HM) and 3-5100143-0 (TE Connectivity Z-PACK) are functional alternatives suitable only when system architecture permits reduction from 132 to 110 positions. Both parts share the 2.00mm pitch, press-fit termination, gold contact finish, board guide feature, and -55°C to 125°C operating range. However, 17011102402 operates at 1.0A (versus 1.5A) with unspecified voltage rating, while 3-5100143-0 maintains 1.5A current rating but operates at 500Vrms (versus 750Vrms). Both alternatives are active products with current compliance certifications (ROHS3 and RoHS respectively).

Selection between these alternatives depends on application current and voltage requirements. The 3-5100143-0 is preferred when 1.5A current capacity is mandatory. The 17011102402 is suitable for lower-current applications where the 1.0A rating is sufficient.

Frequently Asked Questions (FAQ)

Q: Can HM2P07PDP255N9LLF be used as a direct replacement for HM2P07PDP255N9L?

A: Yes. HM2P07PDP255N9LLF is electrically and mechanically identical to the main part. Both are 132-position headers with 2.00mm pitch, press-fit termination, 1.5A current rating, and 750Vrms voltage rating. The difference is packaging (tray) and product status (active). No design changes are required.

Q: What is the key limitation when using 17011102402 or 3-5100143-0?

A: Both alternatives provide 110 positions instead of 132. The original part includes 22 dedicated ground positions; these alternatives do not. System designs must accommodate this position reduction. Additionally, 17011102402 has a 1.0A current rating (lower than the original 1.5A) and unspecified voltage rating.

Q: Are the substitute parts RoHS compliant?

A: Yes. HM2P07PDP255N9LLF is RoHS Compliant. 17011102402 is ROHS3 Compliant. 3-5100143-0 is RoHS Compliant. The original HM2P07PDP255N9L does not specify RoHS status.

Q: What is the difference in contact finish between these parts?

A: All parts use gold contact finish. HM2P07PDP255N9L and HM2P07PDP255N9LLF specify flash thickness. 17011102402 offers gold or gold-palladium. 3-5100143-0 specifies 30.0µin (0.76µm) thickness. These variations are acceptable for equivalent substitution within the 2.00mm pitch press-fit connector category.

Q: Can these parts be used interchangeably in existing PCB designs?

A: HM2P07PDP255N9LLF can be used interchangeably with no PCB modifications. The 110-position alternatives (17011102402 and 3-5100143-0) require PCB redesign to accommodate the reduced position count and different row configuration (5 rows instead of 5 + 1 rows).

Q: What is the moisture sensitivity level for all these parts?

A: All parts are rated MSL 1 (Unlimited), indicating no moisture sensitivity restrictions during storage or handling.