HM2P07PDJ265N9 Equivalent & Substitute Parts

Part Overview

The HM2P07PDJ265N9 is a 132-position backplane connector header manufactured by Amphenol ICC (FCI) in the Millipacs® series. This press-fit through-hole connector features a 2.00mm pitch and supports 1.5A current at 750Vrms. The part is classified as obsolete, necessitating identification of active equivalent alternatives that maintain functional compatibility for backplane applications.

Key Parameters

Parameter	Value
Connector Type	Header, Male Pins
Pitch	0.079" (2.00mm)
Mounting Type	Through Hole
Termination	Press-Fit
Contact Finish	Gold
Current Rating	1.5 A
Voltage Rating	750Vrms
Operating Temperature	-55°C ~ 125°C
Connector Style	A 22
Features	Board Guide
Moisture Sensitivity Level	1 (Unlimited)

Substitute Part Grouping Explanation

Substitution for the HM2P07PDJ265N9 is based on the following critical parameters:

Position Count: The main part contains 132 positions (110 + 22 ground). All identified substitutes provide 110-position configurations, representing a reduction in total position capacity.
Pitch: All substitutes maintain the 0.079" (2.00mm) pitch requirement for mechanical and electrical compatibility.
Connector Type & Style: All substitutes are Header, Male Pins connectors with A 22 style, ensuring mating compatibility.
Mounting & Termination: Through-hole press-fit termination is consistent across all alternatives.
Contact Finish: Gold finish is maintained across all substitutes.
Current Rating: Substitute parts from TE Connectivity maintain 1.5A rating; HARTING substitutes provide 1.0A rating.
Voltage Rating: TE Connectivity substitutes provide 500Vrms; HARTING substitutes do not specify voltage rating.
Temperature Range: All substitutes support -55°C ~ 125°C operating range.
Product Status: All substitutes are active products, addressing the obsolescence of the main part.

Parameter Comparison

Parameter	HM2P07PDJ265N9	1-5100143-9	1-5188398-9	17011102402	3-5100143-0	5100143-1	5106413-1	5188398-9
Manufacturer	Amphenol ICC (FCI)	TE Connectivity AMP	TE Connectivity AMP	HARTING	TE Connectivity AMP	TE Connectivity AMP	TE Connectivity AMP	TE Connectivity AMP
Series	Millipacs®	Z-PACK	Z-PACK	har-bus® HM	Z-PACK	Z-PACK	Z-PACK	Z-PACK
Number of Positions	132 (110 + 22 Ground)	110	110	110	110	110	110	110
Pitch	0.079" (2.00mm)	0.079" (2.00mm)	0.079" (2.00mm)	0.079" (2.00mm)	0.079" (2.00mm)	0.079" (2.00mm)	0.079" (2.00mm)	0.079" (2.00mm)
Connector Type	Header, Male Pins	Header, Male Pins	Header, Male Pins	Header, Male Pins	Header, Male Pins	Header, Male Pins	Header, Male Pins	Header, Male Pins
Connector Style	A 22	A 22	A 22	A 22	A 22	A 22	A 22	A 22
Mounting Type	Through Hole	Through Hole	Through Hole	Through Hole	Through Hole	Through Hole	Through Hole	Through Hole
Termination	Press-Fit	Press-Fit	Press-Fit	Press-Fit	Press-Fit	Press-Fit	Press-Fit	Press-Fit
Contact Finish	Gold	Gold	Gold	Gold or Gold-Palladium	Gold	Gold	Gold	Gold
Current Rating (Amps)	1.5	1.5	1.5	1.0	1.5	1.5	1.5	1.5
Voltage Rating	750Vrms	500Vrms	500Vrms	Not Specified	500Vrms	500Vrms	500Vrms	500Vrms
Operating Temperature	-55°C ~ 125°C	-55°C ~ 125°C	-55°C ~ 125°C	-55°C ~ 125°C	-55°C ~ 125°C	-55°C ~ 125°C	-55°C ~ 125°C	-55°C ~ 125°C
Product Status	Obsolete	Active	Active	Active	Active	Active	Active	Active
RoHS Status	Non-compliant	ROHS3 Compliant	ROHS3 Compliant	ROHS3 Compliant	RoHS Compliant	ROHS3 Compliant	ROHS3 Compliant	RoHS Compliant
REACH Status	REACH Unaffected	REACH Unaffected	Vendor Undefined	REACH Unaffected	Vendor Undefined	Vendor Undefined	Vendor Undefined	Vendor Undefined

Engineering Selection Recommendations

TE Connectivity Z-PACK Series (5100143-1, 5106413-1, 5188398-9, 1-5100143-9, 1-5188398-9, 3-5100143-0): These parts provide the closest electrical match with 1.5A current rating and 500Vrms voltage rating. All are ROHS3 compliant and active products. The 5100143-1 variant offers the highest inventory availability (3040 units) and is recommended as the primary substitute. The 5106164-1 variant includes an alignment strip feature in addition to board guide.

HARTING har-bus® HM Series (17011102402, 17011104201, 17011102204): These alternatives maintain mechanical compatibility with 2.00mm pitch and through-hole press-fit termination. Current rating is reduced to 1.0A, and voltage rating is not specified. All variants are ROHS3 compliant and active products. These are suitable for applications where the reduced current rating is acceptable.

Position Count Consideration: All substitutes provide 110 positions versus the original 132 positions (110 + 22 ground). Design verification is required to confirm that the reduced position count meets application requirements.

Frequently Asked Questions (FAQ)

Q: Can the HM2P07PDJ265N9 be directly replaced with a 110-position substitute?

A: Direct replacement depends on application requirements. The original part provides 132 positions (110 signal + 22 ground), while all substitutes provide 110 positions. PCB layout and connector footprint compatibility must be verified before substitution.

Q: What is the primary difference between TE Connectivity and HARTING substitutes?

A: TE Connectivity Z-PACK substitutes maintain the 1.5A current rating and specify 500Vrms voltage rating. HARTING har-bus® HM substitutes provide 1.0A current rating with unspecified voltage rating. Selection depends on application current and voltage requirements.

Q: Are all substitutes RoHS compliant?

A: Yes. All identified substitutes are either ROHS3 compliant or RoHS compliant, addressing the non-compliant status of the obsolete HM2P07PDJ265N9.

Q: Which substitute has the best inventory availability?

A: The TE Connectivity 5100143-1 (Z-PACK series) has the highest inventory with 3040 units in stock.

Q: Do all substitutes support the same operating temperature range?

A: Yes. All substitutes support the -55°C ~ 125°C operating temperature range consistent with the original part.

Q: What is the significance of the board guide feature?

A: The board guide feature is present on all substitutes and the original part, ensuring proper alignment during PCB assembly and connector mating.

Q: Are there differences in contact finish between substitutes?

A: TE Connectivity substitutes specify gold finish with 30.0µin (0.76µm) thickness. HARTING substitutes specify gold or gold-palladium finish without thickness specification. Both finishes are compatible with standard backplane connector applications.

Request Quote (Ships tomorrow)

Part Number

Quantity

Company

Contact Name

E-mail

Message