HLE-110-02-G-DV-P Equivalent & Substitute Parts

Part Overview

The HLE-110-02-G-DV-P is a 20-position receptacle connector manufactured by Samtec Inc., designed for board-to-board applications with 0.100" (2.54mm) pitch spacing. This surface mount connector features gold-plated female socket contacts and push-pull fastening, operating across -55°C to 125°C. The part is active in production with 1111 units in stock and maintains ROHS3 compliance.

Equivalent and substitute parts are identified to support procurement flexibility, inventory management, and design alternatives when the primary part becomes unavailable or when design requirements permit functional alternatives.

Substiute Parts

HLE-110-02-G-DV-P

Samtec Inc.In Stock: 1160HLE-110-02-G-DV-P Datasheet

Current PartRFQ

NPPC102KFMS-RC

Sullins Connector SolutionsIn Stock: 7074NPPC102KFMS-RC Datasheet

MFR RecommendedRFQ

Key Parameters

Substitute Part Grouping Explanation

The NPPC102KFMS-RC from Sullins Connector Solutions is identified as a manufacturer-recommended substitute based on the following critical parameters:

Matching Parameters:

• 20-position connector configuration
• 0.100" (2.54mm) mating pitch
• 2-row layout with 0.100" (2.54mm) row spacing
• Surface mount solder termination
• Push-pull fastening mechanism
• Gold-plated mating contacts
• Square contact geometry
• Board-to-board application suitability
• ROHS3 compliance
• MSL 1 rating

Functional Equivalence Basis: Both connectors support identical mating pitch, position count, and row configuration, enabling direct mechanical and electrical interface compatibility in board-to-board applications. The gold contact finish and push-pull fastening ensure equivalent signal integrity and connection reliability.

Parameter Comparison

Engineering Selection Recommendations

Primary Part Selection (HLE-110-02-G-DV-P): Select the HLE-110-02-G-DV-P when applications require the full operating temperature range of -55°C to 125°C, higher current capacity of 4.1A per contact, or 400VAC voltage rating. The Liquid Crystal Polymer insulation material and beryllium copper contacts provide enhanced performance characteristics. ROHS3 compliance and MSL 1 rating support unrestricted storage and handling.

Substitute Part Selection (NPPC102KFMS-RC): The NPPC102KFMS-RC is suitable for applications operating within -40°C to 125°C temperature range and requiring maximum 3A per contact and 250V rating. This substitute maintains identical mechanical interface compatibility and ROHS3 compliance. The higher insulation height (0.299" vs 0.144") may require PCB layout verification to ensure clearance compatibility.

Both parts are active products with established supply chains and full RoHS3 compliance certification.

Frequently Asked Questions (FAQ)

Q: Can NPPC102KFMS-RC directly replace HLE-110-02-G-DV-P in all applications?

A: Direct mechanical and electrical interface compatibility exists for the 20-position, 0.100" pitch configuration. However, verify that application requirements fall within the NPPC102KFMS-RC operating parameters: -40°C to 125°C temperature range, 3A maximum current per contact, and 250V maximum voltage rating. PCB layout must accommodate the increased insulation height of 0.299" compared to 0.144".

Q: What are the key differences between these connectors?

A: The primary differences are operating temperature minimum (-55°C vs -40°C), current rating per contact (4.1A vs 3A), voltage rating (400VAC vs 250V), insulation height (0.144" vs 0.299"), contact material (beryllium copper vs phosphor bronze), and insulation material (LCP vs polyamide). Mechanical pitch, position count, and row configuration are identical.

Q: Are both parts RoHS3 compliant?

A: Yes, both HLE-110-02-G-DV-P and NPPC102KFMS-RC maintain ROHS3 compliance and MSL 1 (unlimited) moisture sensitivity ratings.

Q: What is the impact of different insulation heights on PCB design?

A: The NPPC102KFMS-RC insulation height of 0.299" is 0.155" taller than the HLE-110-02-G-DV-P at 0.144". Verify clearance above the connector footprint on the PCB to prevent interference with adjacent components or enclosure features.

Q: Which part should be specified for high-temperature applications?

A: The HLE-110-02-G-DV-P supports the extended lower temperature limit of -55°C, making it the appropriate choice for applications requiring full -55°C to 125°C operation. The NPPC102KFMS-RC minimum operating temperature is -40°C.